Parts for Lg DLG7061VE: Control Panel / Plate Assy Parts

The Tub Assembly is an OEM component for LG clothes dryers. As the central component housing both the inner and outer drums, the tub assembly is essential for safely drying wet laundry loads. It rotates the drums to circulate air and remove moisture from clothes during cycles. 

Causes of a bad tub assembly dryer can include cracks, leaks, or damage to the drum structure from excessive use or unbalanced loads over time. Wear and tear on rotating or suspension components that impair rotation. 

Symptoms of an issue with the tub assembly dryer are:

• Inefficient or slow drying times 
• Abnormal noises or vibrations during cycles
• Restricted or lack of drum rotation
• Cracks, leaks, or physical damage visible on drums

This OEM LG part is also compatible with Sears/Kenmore.

The Gas Burner Valve Assembly is an OEM replacement part for LG gas dryers. It is a component located beneath the gas burner that controls the flow of fuel to ignite and maintain the flame. The valve assembly receives ignition and temperature signals from the dryer's control system to precisely regulate gas levels throughout drying cycles. This gas dryer burner valve includes two solenoid coils.

Causes of a faulty gas valve may involve wear over extended operation, mineral buildup on valve seats, or mechanical issues restricting gas flow at desired levels.

Symptoms of a bad gas burner valve assembly consist of:

• Erratic or inconsistent burner ignition between cycles
• Inability to achieve high heat settings when needed
• Burners not maintaining steady flame patterns
• Potential gas leaks detected around valves or tubing

This OEM LG part is also compatible with some Sears/Kenmore dryers.

This display power control board assembly powers and controls the appliance display and front-panel electronics so the user interface responds correctly. Replaces a failed display control board to restore readable indicators and responsive controls. What it does:

• Supplies regulated power to the control panel and display modules.
• Manages display backlight and indicator LEDs so settings and status are visible.
• Helps resolve symptoms like a blank or unresponsive display, missing indicators, or intermittent panel behavior.
• Works as the replacement for the main display/control electronics—does not include user interface overlays or buttons unless listed below.

• One display power control board assembly.

• Disconnect power (unplug or shut off breaker) before accessing electronics to avoid shock or damage.
• Handle the board by edges and avoid touching contacts or components to prevent static damage.
• Verify matching part number on the old board before installation; connector positions should match the replacement.

The Dryer Drum Baffle is an OEM part for LG dryers. This baffle is attached to the inside of the dryer drum and is designed to help lift and tumble clothes during the drying cycle. 

Causes of a bad dryer drum baffle can include wear and tear from regular use, physical damage from heavy or sharp objects, or becoming loose due to vibration over time. 

Symptoms of a bad dryer drum baffle include:

• Thumping or banging noises during the drying cycle
• Clothes not tumbling properly, leading to uneven drying
• Loose or rattling baffle inside the drum
• Visible damage or breakage on the baffle

This OEM LG part is also compatible with some Kenmore models.

This is a four ribbed poly V belt.

The Drum Seal is an OEM part for LG dryers. This part ensures a tight seal between the dryer drum and the dryer body, preventing hot air from escaping and maintaining the efficiency of the drying process. A well-functioning drum seal is important for the best dryer performance, contributing to energy efficiency and the prevention of unnecessary wear on clothing during the drying cycle.

Causes of a bad drum seal can range from natural wear and tear over time to overloading the dryer, which can strain and stretch the seal, leading to a poor fit.  

Symptoms of a bad Drum Seal include:

• Clothes taking longer to dry
• Increased energy usage due to loss of heat
• Excessive lint and debris outside of the lint filter area
• A noticeable gap between the dryer drum and the dryer body

This OEM LG part is also compatible with some Kenmore models.

This genuine replacement window restores a clear, intact viewing panel for your microwave door so you can safely monitor cooking. It replaces cracked, chipped, or cloudy glass to improve visibility and maintain proper door fit. What it does:

• Provides a transparent viewing panel for safe monitoring of food while cooking
• Restores door integrity when original glass is cracked, chipped, or scratched
• Helps maintain proper door sealing and keeps heat contained
• Reduces glare and cloudiness from damaged or aged glass

• One microwave door window (1 piece)

• Disconnect power to the appliance before starting any repair
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Follow OEM service instructions for door disassembly and reassembly; use correct screws/clips
• Replace any damaged door hardware or gasket for proper fit and safety

This Taptite screw is a factory thread-forming fastener used to secure panels, brackets, and internal components where specified by the manufacturer. It forms threads as it drives for a secure, long-lasting hold when replacing a missing or damaged screw.

• Fastens covers, brackets, and internal parts at the designated mounting points
• Thread-forming "Taptite" design creates mating threads in the receiving hole for a snug fit
• Helps restore alignment and reduce vibration or rattling from loose hardware
• Typical symptoms: loose or misaligned panel/handle, rattles during operation, missing or stripped screw

• Disconnect power (and shut off water/gas if applicable) before servicing
• Replace only in the exact location specified for this part; match head style and length to the original
• Start by hand to avoid cross-threading; if resistance is high, back out and re-start
• Tighten until snug; do not overtighten to prevent stripping or cracking

This Pipe Assembly routes water into the appliance so the dispenser and ice maker can receive a steady supply. Replacing a damaged tube restores proper water flow and helps stop leaks or pooling inside or beneath the unit. What it does:

• Carries incoming water from the household supply to the appliance's internal water system
• Restores water delivery to the dispenser and ice maker when the original tube is cracked or blocked
• Prevents leaks and water damage caused by split, corroded, or pinched tubing
• Helps eliminate intermittent flow or weak dispenser output caused by a damaged water line

• One complete pipe assembly as shown

• Shut off the refrigerator's water supply and unplug the appliance before beginning
• Handle tubing fittings carefully; use proper tools to avoid damage or overtightening
• Inspect connection points and replace seals or clips if worn; test for leaks after reinstalling

The Dryer Ignitor is an OEM part for LG dryers. It is crucial for the ignition process in gas dryers, responsible for lighting the gas burner that provides heat for drying clothes. This ignitor must heat up to a high temperature to ignite the gas, and its proper function is essential for the dryer to operate safely and efficiently.

Symptoms of a bad Dryer Ignitor include:

• The dryer not heating up, even though all other functions are working correctly.
• The gas valve opening but no flame being produced, indicating the ignitor isn't reaching the necessary temperature.
• Intermittent heating, where the dryer sometimes produces heat and other times does not.

Causes of a bad dryer ignitor can include thermal fuse issues, a broken or malfunctioning ignitor due to wear and tear, or electrical problems affecting power delivery to the ignitor.

This OEM LG part is also compatible with Kenmore models.

For propane order 383EEL3002A.

The LP Conversion Kit is an OEM part for LG dryers. This kit is designed to convert a natural gas dryer to use liquid propane (LP) gas. It includes all necessary components to make the conversion safely and effectively, ensuring the dryer operates efficiently with LP gas.

Causes of needing an LP Conversion Kit can include relocating the dryer to an area where only LP gas is available or switching from natural gas to LP gas to meet specific household energy requirements. Proper installation of the conversion kit is crucial for safe and efficient dryer operation.

Symptoms indicating the need for an LP Conversion Kit include:

• Relocating to a home with LP gas service
• Switching energy sources due to availability or preference
• A new dryer installation where only LP gas is supplied

This OEM LG part is also compatible with Sears/Kenmore.

Replacement door gasket that seals the refrigerator/freezer door to help keep cold air in, reduce energy loss, and maintain consistent temperatures for stored food. What it does

• Forms an airtight seal around the door to prevent warm air from entering the compartment.
• Helps maintain even cooling and prevents frost or ice buildup caused by air leaks.
• Can reduce running time and energy use when the original gasket is torn, warped, or no longer seals.
• Common symptoms of a failing gasket: visible gaps, condensation or frost at the door, uneven temperatures, or increased energy use.

• Disconnect power to the appliance and remove food from affected areas before beginning work.
• Inspect the door frame for dirt or debris and clean mating surfaces before installing the new gasket.
• Align the gasket to the door and seat it fully—follow OEM alignment steps for your model; if the gasket is stiff, warm it slightly per OEM guidance to help fit.

This duct assembly channels airflow inside the appliance to guide exhaust and internal air between components. Replacing a damaged or obstructed duct helps restore proper airflow and can reduce poor performance or long cycles. What it does:

• Directs exhaust and circulation air between internal components to maintain airflow
• Prevents leaks that can reduce efficiency or cause longer cycle times
• Helps avoid overheating or moisture build-up from restricted airflow
• Reduces rattling or vibration caused by a cracked or loose duct

• Disconnect power (and turn off gas supply for gas appliances) before beginning work.
• Handle edges carefully — sheet metal can be sharp; wear cut-resistant gloves.
• Ensure duct is seated and fastened to create a tight seal where it connects to other components.
• After reassembly, run a test cycle to confirm airflow and proper operation.

This upper plate is the replaceable trim/cover that fits inside the top of the microwave cavity to protect internal components and help direct airflow. Replacing a damaged plate restores proper coverage and reduces debris buildup. What it does

• Covers and protects internal microwave components at the top of the cavity
• Helps maintain proper airflow and part alignment inside the oven
• Prevents food and debris from contacting internal wiring and electronics
• Reduces rattling or vibrations caused by a warped or loose plate
• Visible cracks, warping, or burn marks are common signs it needs replacement

• One upper plate as pictured

• Disconnect power at the wall and allow the oven to fully power down before servicing
• Remove fasteners or clips holding the old plate, align tabs, then secure the new plate with the original hardware
• Do not operate the microwave with covers removed; complete the repair

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The High Limit Thermostat is an OEM part for LG dryers, designed to act as a critical safety feature within the appliance. This thermostat monitors the dryer's internal temperature, shutting off the heat source if it detects temperatures that are dangerously high. By doing so, it prevents overheating, which can lead to appliance damage or, in worst-case scenarios, fires. The high limit thermostat is a crucial component for the safe operation of your dryer, ensuring it operates within the specified temperature range.

Causes of a faulty High Limit Thermostat can include a malfunction within the thermostat itself, such as a failure to accurately detect temperature changes, or issues with the dryer that cause it to run hotter than designed, such as restricted airflow or a malfunctioning heating element.

Symptoms of a malfunctioning High Limit Thermostat include:

• The dryer not heating properly or at all
• The dryer repeatedly shutting off during cycles
• Excessive heat emanating from the dryer, indicating it is not regulating temperature correctly

This OEM LG part is also compatible with some Kenmore models.

The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition temperature.

Over time, the igniter sensor can become faulty due to regular use, exposure to high temperatures, or electrical issues. These factors can lead to a malfunction, resulting in the dryer not heating properly or failing to start.

Symptoms of a bad igniter sensor include:

• Dryer not heating up
• Long drying times
• Dryer not starting
• Unusual smells or noises during operation

This OEM LG part is also compatible with Sears/Kenmore.

A small mounting bracket that secures and supports internal appliance components to keep shelves, drawers or assemblies aligned and stable. Replaces a cracked, broken or missing supporter to restore proper fit and reduce movement. What it does

• Secures an internal component or assembly in place to prevent sagging or misalignment
• Stops rattling, wobble or looseness caused by a damaged or missing bracket
• Restores correct clearance and support for the associated shelf/drawer/assembly
• Helps maintain normal operation and prevents further wear on adjacent parts

• One supporter holder bracket

• Disconnect power before starting repairs; unplug or flip the appliance breaker
• Remove nearby shelves, drawers or panels to access the damaged bracket
• Inspect mating parts for damage and replace any worn fasteners as needed
• Use basic hand tools;

The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance. 

Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.

Symptoms of a bad Roller Kit include:  

• Loud squeaking, rumbling, or thumping noises during operation  
• The dryer drum not spinning or rotating unevenly  
• Excessive vibrations while the dryer is running  

This OEM LG part is also compatible with Sears/Kenmore.

A manufacturer-configured replacement component designed to restore the appliance's original factory settings and functions. Use this part when a model-specific, pre-configured module is required to return correct operation. What it does:

• Provides the factory-specific configuration and setup programmed by the manufacturer
• Restores functions controlled by the module when configuration or programming is corrupted
• Resolves symptoms such as appliance not starting, control panel unresponsive, or intermittent/erratic operation linked to configuration errors
• Ensures compatibility with model-specific features when the appliance requires a pre-configured assembly

• Disconnect power to the appliance before starting any work
• Handle electronics carefully; observe electrostatic discharge (ESD) precautions for circuit boards or modules
• Match connectors and mounting locations to the original part; do not force connectors

The Hinge is an OEM part for LG dryers, designed to enable smooth door operation. This critical component ensures proper alignment and efficient sealing to prevent heat loss and noise. Continuous use may cause wear, affecting alignment, sealing, and dryer safety and efficiency.

Causes of a bad hinge can include physical wear from regular use, leading to loosening or deformation, corrosion or rust weakening the hinge and affecting its movement, and accidental damage like bending due to impact, impairing the door's ability to close properly.

Symptoms of a bad Hinge include:

• The dryer door hangs unevenly or won't close tightly.
• Increased difficulty in opening or closing the door.
• Squeaking, grinding, or other noises when the door is moved.
• Visible wear or damage, such as bending or breaking.

This OEM LG part is also compatible with some Kenmore models.

Restore smooth, aligned door movement with this refrigerator door hinge assembly. A worn or bent hinge can cause sagging and poor sealing; replacing it helps the door close properly so your fridge maintains consistent performance. What it does:

• Allows the door to pivot smoothly on the cabinet
• Helps keep the door aligned for proper gasket contact and sealing
• Replaces worn or bent hinge components to restore correct door operation
• Typical symptoms: door sagging or rubbing, difficulty closing, uneven gasket contact, squeaks/clicks when opening or closing

• One hinge assembly

• Unplug the refrigerator; shut off water supply to the unit
• Support the door and use a second person to prevent dropping or misalignment
• Note/mark hinge positions and transfer any spacers or caps from the original hinge as needed
• After installation, verify even gasket contact and adjust leveling before tightening fasteners fully

The Lint Filter is an OEM part for LG dryers. It serves a critical function in trapping lint and debris from clothes during the drying process. Located in the door or top of the dryer, depending on the model, this filter ensures efficient airflow and heat distribution by preventing lint from clogging the dryer vent. 

These issues typically arise from normal wear and tear or from not regularly cleaning the filter, which can cause it to become brittle or damaged over time.  

Symptoms of a bad Lint Filter include:

• Reduced drying efficiency, leading to longer drying times
• Excessive lint or debris escaping into the dryer vent, which can pose a fire risk
• Visible wear or damage to the filter, such as tears or holes, which can allow lint to pass through

This OEM LG part can also be used on Kenmore/Sears appliances. 

This replacement holder secures a small appliance component in place to restore proper alignment and reduce vibration. It's a direct-fit bracket designed to hold components steady and prevent movement that can cause noise or malfunction. What it does:

• Keeps the associated component firmly mounted to its chassis or support
• Prevents rattling, misalignment, or intermittent contact caused by a damaged or missing holder
• Helps maintain proper operation of the component it supports
• Common symptoms: visible crack or break in the holder, loose or shifting component, or new noise from the area

• One replacement holder as shown

• Disconnect power and/or water supply before beginning any repair
• Inspect surrounding parts for damage before installing the new holder
• Basic hand tools are typically required; avoid overtightening fasteners

This hole cap is a small trim piece that covers an unused or service access hole to protect the appliance internals and give a finished appearance. It reduces debris entry and minimizes snag points on the cabinet. What it does:

• Covers an unused access or mounting hole in the cabinet or control panel
• Helps keep lint, dust, and moisture out of internal cavities
• Provides a finished look and helps prevent clothing or items from catching
• Simple snap-in design for a secure fit

• One hole cap

• Disconnect power to the appliance before accessing panels or openings
• Typically snaps into place from the outer side of the panel; a small flat tool can help with removal
• Do not force or pry excessively to avoid cracking the cap or panel
• If the cap does not seat securely, check correct part and seating orientation before applying pressure

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

This locker assembly secures the washer door and completes the latch housing so cycles can run safely. Replacing a worn or damaged locker helps restore proper door closure and reliable start/stop operation. What it does:

• Secures and aligns the washer door/boot so the machine can operate without the door opening during a cycle.
• Engages the door latching mechanism so the washer can detect a closed door and start.
• Replaces a damaged or cracked lock housing that can prevent the door from staying closed.
• Common symptoms this part can address: washer won't start, door won't latch or stays open, or the door pops open during a cycle.

• Disconnect power (and water, if applicable) before starting any repair to avoid shock or injury.
• Basic hand tools are typically required; follow the OEM service manual for panel and door removal.
• Handle door glass and trim carefully to avoid damage; transfer any mounting brackets or strike plates only if needed.
• After installation, restore power and run a short test cycle to verify the door latches and the washer starts normally.

Note: Does not include moisture sensor bars. For the moisture sensor bars, order 2 of part# 6500EL3001A.

The Guide Cover is an OEM part for LG dryers. The part allows dust and debris to exit the dryer drum while preventing small clothing items from slipping through.

Causes of a bad Guide Cover can include accumulation of lint and debris that can restrict airflow, physical damage from handling or excessive use, and general wear that can compromise the fit and effectiveness of the cover.

Symptoms of a bad Guide Cover include:

• Increased drying times due to poor airflow.
• Unusual noises from lint hitting the fan or other components.
• Overheating of the dryer.
• Visible damage or misalignment of the cover that affects performance.

This OEM LG part is also compatible with Sears/Kenmore.

This precision fastener is designed for specific locations on the appliance. Replacing a missing or damaged screw restores secure mounting and reduces vibration or rattling, helping panels and components stay properly aligned.

• Secures brackets, panels, and internal assemblies where this screw is specified
• Replaces stripped, rusted, or lost hardware
• Helps eliminate looseness, vibration, and noise
• Maintains proper fit and alignment of parts

• Disconnect power and shut off water/gas before servicing
• Use the correct driver; keep removed hardware organized for reassembly
• Do not overtighten; install into clean, undamaged threads
• Confirm location and quantity using your model's parts diagram

The Door Switch Assembly is an OEM part for LG dryers. It ensures the dryer operates only when the door is securely closed, acting as a safety feature to prevent the dryer from running while the door is open.

Causes of a bad door switch assembly can include regular wear and tear from frequent use, electrical issues such as shorts or faulty connections, or physical damage from forceful door closures or impacts.

Symptoms of a bad door switch assembly include:

• The dryer not starting
• The dryer stopping mid-cycle
• The drum light not turning on or off correctly
• The dryer continuing to run with the door open

This OEM LG part is also compatible with Sears/Kenmore models.

The Filter Guide is an OEM part for LG dryers. It plays a pivotal role in guiding and securing the lint filter in place within the dryer. This ensures that lint and other debris are effectively captured during the drying cycle, preventing them from clogging the vent or damaging internal components. 

Causes for replacement include physical damage, such as cracks or warping, which can occur from frequent use or accidental mishandling. A malfunctioning filter guide can compromise the dryer's ability to trap lint, potentially leading to overheating, decreased efficiency, or even a fire hazard.

Symptoms of a bad filter guide include:

• Difficulty in inserting or removing the lint filter
• Excessive lint accumulation outside the filter area
• The dryer taking longer to dry clothes or not drying effectively
• Unusual noises or vibrations indicating that debris is bypassing the filter

This OEM LG part is also compatible with some Kenmore models.

The Filter Guide is an OEM part for LG dryers. It plays a pivotal role in guiding and securing the lint filter in place within the dryer. This ensures that lint and other debris are effectively captured during the drying cycle, preventing them from clogging the vent or damaging internal components. 

Causes for replacement include physical damage, such as cracks or warping, which can occur from frequent use or accidental mishandling. A malfunctioning filter guide can compromise the dryer's ability to trap lint, potentially leading to overheating, decreased efficiency, or even a fire hazard.

Symptoms of a bad filter guide include:

• Difficulty in inserting or removing the lint filter
• Excessive lint accumulation outside the filter area
• The dryer taking longer to dry clothes or not drying effectively
• Unusual noises or vibrations indicating that debris is bypassing the filter

This OEM LG part is also compatible with some Kenmore models.

This distortion spring applies the correct tension within the dryer mechanism so parts return to position and operate smoothly. Replacing a fatigued or broken spring helps prevent loose movement, rattling, and inconsistent operation of the related assembly. What it does

• Provides the designed return/tension force for the associated dryer mechanism
• Helps maintain alignment and smooth movement of moving parts
• Can reduce rattling or squeaking caused by weak or missing spring tension
• Symptoms include components not returning to position or intermittent operation

• One distortion spring

• Disconnect power; for gas dryers, also shut off the gas supply
• Allow internal components to cool before service
• Control the spring during removal/installation—springs are under tension and can snap back
• Note the original spring orientation and attachment points to ensure proper reassembly

This factory fastener is the customized screw used to secure components on compatible LG appliances. It replaces missing or damaged screws to keep brackets, panels, and covers tight so parts stay aligned and rattle-free.

• Secures brackets, panels, trim, or covers at their mounting points
• Helps maintain alignment and reduce looseness, gaps, squeaks, and rattling
• Replaces stripped, rusted, or missing screws caused by vibration or wear
• Restores proper hold so components stay in place during normal use

• Disconnect power; shut off water to the appliance if applicable
• Use the correct driver bit and apply straight, firm pressure to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

This moisture sensor connector assembly links the dryer's sensor bars to the control to monitor fabric dryness and adjust cycle time. Replacing a damaged or loose harness restores consistent Auto Dry operation.

• Connects the moisture sensor bars to the main control for Auto Dry feedback
• Transmits the low-voltage signal used to determine when clothes are dry
• Failure may cause Auto Dry to end too soon, run too long, or deliver inconsistent results
• Typical issues include broken wires, loose/corroded terminals, or a heat-damaged plug

• Disconnect power; if gas, shut off gas supply before service
• Access the moisture sensor area at the front/lint housing
• Match routing and clips, seat terminals fully on the sensor tabs, and secure the connector
• Keep wiring clear of sharp edges and moving parts; reassemble and test a Sensor Dry cycle

This damper assembly mounts at the microwave's exhaust outlet to direct airflow outside and block backdraft when the fan is off. Replacing a cracked or warped damper restores venting performance and helps reduce drafts and rattling noise.

• Opens with blower airflow and closes when off to help prevent outside air from entering through the duct
• Directs steam, smoke, and cooking odors to the exhaust path
• Helps reduce drafts/backdraft when the fan is not running
• Common failure signs: weak venting, flap stuck open/closed, or rattling/flapping noises

• Disconnect power at the breaker; if over-the-range, support the unit per manufacturer instructions
• Remove the vent grille/top cover to access the outlet and take out the old damper; reuse existing hardware as needed
• Match the new damper's orientation to the original so the flap opens with airflow and moves freely
• Beware sharp sheet-metal edges; wear cut-resistant gloves and test the fan after reassembly to confirm proper operation

This hinge bracket anchors the door hinge to the appliance cabinet, keeping the door aligned for smooth opening and a reliable seal. Replacing a bent or worn bracket restores proper door movement and reduces rubbing, sagging, and gaps.

• Secures the hinge to the cabinet/frame and supports door weight during operation
• Helps maintain door alignment for consistent gasket contact
• Restores smooth pivoting of the door
• Common signs it's needed: door sagging or rubbing, popping/creaking at the hinge area, loose mounting, or visible damage to the bracket

• Disconnect power; if applicable, shut off water
• Support the door while servicing; a second person is recommended
• Note hinge/bracket orientation and transfer any spacers/shims and hardware from the old bracket
• Tighten mounting screws evenly and verify door gaps and seal contact before restoring power

This holder is a small mounting bracket that secures internal components in place, helping prevent movement and vibration for reliable operation. It's a simple replacement part that restores proper fit and stability. What it does:

• Secures and supports nearby components or assemblies to prevent shifting
• Reduces vibration and rattling that can cause noise or wear
• Helps maintain correct alignment for connected parts to operate smoothly
• Restores original component retention after damage or loss of the bracket

• Disconnect power to the appliance before beginning any repair
• Basic hand tools may be required; handle small parts carefully to avoid loss
• Inspect surrounding clips and fasteners; replace any that are damaged

This replacement locker hook mounts on the dryer door and engages the cabinet catch and door switch. It keeps the door securely closed so cycles can start and continue without interruption. What it does:

• Attaches to the door and latches into the cabinet catch to secure the door
• Actuates the door switch so the appliance recognizes the door is closed
• Replaces a cracked, bent, or worn hook
• Resolves issues like the door not latching, popping open, or the unit not starting

• 1 locker hook

• Disconnect power; if gas, also shut off the gas supply
• Open the door and remove the mounting screws securing the old hook
• Position the new hook and tighten screws, reusing existing hardware
• Check latch alignment; the door closes securely and the cycle starts

This replacement hinge supports and pivots the appliance door so it opens and closes smoothly while staying aligned for a proper seal. Replacing a worn or bent hinge restores consistent door action and helps prevent latch and sealing issues.

• Provides the pivot point that allows the door to open and close
• Maintains door alignment so the latch and gasket engage correctly
• Helps prevent sagging, rubbing, and poor sealing
• Common symptoms: drooping or loose door, difficulty closing, binding/squeaking, visible damage

• Disconnect power before servicing; allow any hot surfaces to cool
• Support the door during removal/installation to prevent damage or injury
• Transfer any spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and gasket contact; adjust per service information if needed

This door hinge supports and pivots the appliance door so it opens smoothly and closes securely, maintaining proper alignment and latch engagement. Replacing a worn hinge restores consistent door operation and helps prevent sagging, rubbing, and incomplete closure.

• Provides the pivot point and structural support for the door
• Helps keep the door aligned for proper latching and closure
• Common signs: door sagging, rubbing, or binding during operation
• Door won't close flush or pop open unexpectedly
• Visible hinge wear, looseness, or damage

• Disconnect power to the appliance before servicing
• Support the door to relieve hinge load before removing screws or pins
• Transfer any reusable spacers, bushings, or screws from the old hinge
• After installation, verify door alignment and latch engagement; adjust as needed

This hinge bracket secures the refrigerator door hinge to the cabinet, restoring stable door alignment and smooth opening. It replaces a worn or damaged mounting bracket so the door closes evenly and stays properly supported. What it does:

• Provides the structural mounting point for the door hinge to attach to the cabinet
• Restores proper door alignment and prevents sagging or uneven gaps
• Reduces binding and noisy operation caused by a bent or broken bracket
• Helps ensure the door seals correctly for consistent cooling performance

• One hinge bracket

• Designed for a direct replacement; use appropriate tools and support the door before removing hinge fasteners to avoid injury or damage
• Disconnect power and remove food from door edges if required by the manufacturer's service instructions
• Retain original screws or order as specified by the OEM

This hinge support is a replacement mounting bracket that helps secure and stabilize a door hinge assembly for proper alignment and smooth opening. It restores correct hinge positioning to reduce sagging and uneven door movement. What it does:

• Supports the door hinge assembly to maintain proper door alignment
• Helps prevent door sagging, binding, and uneven gaps
• Provides a stable mounting point for hinge pins and related hardware
• Used when hinge mounting points are cracked, worn, or damaged

• Basic hand tools required; inspect surrounding hinge components and replace any damaged fasteners
• Tighten screws to secure the support but avoid over-torquing to prevent cracking
• Disconnect power or follow appliance-specific safety steps when working near electrical components

This hinge bracket secures the door hinge assembly to the cabinet, restoring proper door support and alignment for smooth opening and a tight seal. Use it when the hinge area is cracked, worn, or no longer holding the door square. What it does

• Supports and anchors the door hinge so the door stays aligned and closes properly
• Replaces a cracked, broken, or worn bracket that causes door sag or misalignment
• Helps stop rubbing, gaps, and uneven sealing caused by a loose or damaged hinge area
• Works as a direct-fit structural part for the hinge assembly on compatible LG units

• One hinge bracket

• Disconnect power to the appliance and empty the door before starting; have a helper support the door during removal/installation
• Use the correct screwdriver/socket size to remove and reinstall mounting fasteners; do not overtighten
• Inspect hinge pins, screws, and surrounding mounting points; replace any damaged hardware
• After installation, verify door alignment and seal; adjust hinge position if needed following OEM guidance

This door gasket forms a watertight seal between the appliance's tub opening and the door, keeping wash water contained during operation. Replacing a worn seal helps stop leaks and protects floors and nearby cabinetry. What it does:

• Creates a tight, water-resistant seal around the door opening
• Replaces a torn, cracked, flattened, or deformed gasket that can leak
• Common symptoms: drips from the door area, puddles at the front corners, visible damage or mildew on the seal
• Restores proper door compression and helps prevent moisture/steam from escaping

• 1 door gasket

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel and mating surfaces
• Seat the new gasket evenly; ensure it is fully pressed into its channel (some models use retaining bands or clips—transfer and reinstall as removed)
• Close the door to check for uniform contact, then run a short cycle to verify no leaks

This connector bar secures and routes wiring or modules inside the appliance, keeping electrical connections stable and components properly aligned for reliable operation. Use it to restore secure connections and proper part seating. What it does:

• Provides a stable mounting and routing point for harnesses or small modules
• Helps prevent loose or pinched wires that can cause intermittent operation
• Keeps components properly aligned so connectors mate fully
• Supports safe, organized internal wiring to reduce strain on terminals

• Always unplug the appliance before starting work to avoid electrical shock
• Handle wiring gently and ensure all connectors fully seat during reassembly
• Basic hand tools are typically required; reference the service manual for disassembly steps

Note: This is the vertical bar connector.
 

This replacement locker handle restores a secure grip and reliable latch operation on the appliance door or access panel. It replaces a cracked, loose, or missing handle so the door opens and closes smoothly. What it does:

• Provides a firm handhold for opening and closing the door or access panel
• Secures the door latch area to help maintain proper closure
• Replaces broken, cracked, or worn handles that are hard to grip
• Helps reduce rattling or loose-feeling door operation

• One locker handle

• Disconnect power to the appliance before beginning any repair
• Remove any trim or access panels as needed; use basic hand tools
• Handle may attach with clips or screws — keep hardware organized for reassembly
• Test door operation after installation; if fit feels incorrect, check part number and orientation

This Cover Cap is a small trim piece that snaps into place to hide fasteners and finished edges for a clean, finished appearance. It restores the appliance's look and helps prevent dirt from collecting in exposed screw openings. What it does:

• Covers exposed screws and mounting holes for a neater appearance
• Helps keep dirt and debris out of openings around trim pieces
• Prevents accidental contact with fastener heads
• Useful when an original cap is cracked, missing, or faded

• Snap-in replacement; no special tools usually required
• Remove any broken fragments before installing the new cap
• Press firmly until the cap clicks into place; avoid forcing if it doesn't seat easily
• Disconnect power or follow safety steps before working near electrical components

This customized screw secures appliance panels and components for a reliable fit, helping maintain proper alignment and reduce vibration or rattling. Designed as a direct replacement to restore original fastening where the correct screw is required. What it does:

• Fastens panels, brackets, or components to prevent movement and vibration
• Restores secure mounting when a screw is missing, stripped, or damaged
• Helps stop rattling or intermittent contact caused by loose hardware
• Matches the OEM style for correct fit and function when replacing a lost or worn fastener

• Disconnect power to the appliance before performing any repairs
• Use the proper screwdriver or driver bit to avoid stripping the screw head
• Do not overtighten; snug until secure to avoid damaging threads or components
• Keep small parts away from children and pets during installation

This replacement cap for a dryer restores the original protective cover that secures and seals drier components, helping keep lint and debris out and maintaining normal operation. Use it when the original cap is cracked, missing, or damaged. What it does:

• Covers and protects internal dryer components from lint and debris buildup
• Helps maintain proper airflow and reduces risk of trapping lint in moving parts
• Prevents loose parts from rattling or causing vibration-related noise
• Common symptom: visible cracks, missing cap, excessive lint accumulation, or unusual rattling

• Disconnect power (and gas supply for gas models) before starting any repair.
• Basic hand tools may be required; handle plastic parts carefully to avoid damage.
• Reassemble panels and verify operation; inspect for proper fit and clearance.

The Blower Wheel is an OEM part for LG dryers. This part circulates air through the dryer drum and out the exhaust vent, ensuring proper airflow for efficient drying of clothes.

Causes of a bad blower wheel can include accumulation of lint and debris, wear and tear over time, or physical damage due to foreign objects entering the blower housing.  

Symptoms of a bad blower wheel include:

• Reduced or no airflow from the exhaust vent
• Unusual noises such as rattling or squealing during the drying cycle
• Clothes taking longer to dry or remaining damp
• Overheating or frequent shutdowns of the dryer

This OEM LG part is also compatible with some Kenmore models.

Adapt your gas dryer for propane with this LP conversion kit. It provides the correct orifice and regulator adjustments needed so the burner fires properly on LP fuel, helping ensure safe operation and consistent drying performance after a fuel change.

• Converts a compatible gas dryer from natural gas to liquid propane (LP)
• Helps ensure proper burner flame characteristics on LP
• Appropriate when moving to a home with propane or changing utilities
• Symptoms can include weak heat, improper flame, or sooting

• Disconnect power and shut off gas before servicing
• Installation and regulator/orifice adjustments must be performed per the service manual
• After installation, leak-check all connections and verify proper burner operation
• Do not attempt conversion without the correct kit for your specific model

Blower housing assembly for dryer that channels heated air from the drum to the exhaust. Replaces a cracked or damaged housing to restore proper airflow and help the dryer dry more efficiently and quietly. What it does:

• Channels heated air from the drum to the exhaust and supports the blower wheel.
• Restores airflow when a damaged or cracked housing is restricting ventilation.
• Commonly used to address reduced drying performance and longer dry times.
• Can also resolve unusual rattling or grinding noises coming from the lower front of the dryer.

• Disconnect power (and gas, if applicable) before beginning work; wear eye protection and gloves.
• Remove access panels and disconnect vent/ducting per your model's service instructions to reach the blower housing.
• Inspect the blower wheel and surrounding seals/gaskets while the housing is out; replace damaged components as needed.
• Reassemble all panels and venting securely and test the dryer for proper airflow and operation after installation.

This dryer duct assembly channels air from the drum to the blower and exhaust. Replacing a cracked or warped housing restores proper airflow, helps prevent lint bypass, and supports consistent drying performance.

• Directs and seals airflow between the drum and blower housing
• Helps maintain drying efficiency by minimizing leaks and lint bypass
• Damage or warping can lead to long dry times and reduced airflow
• Signs of failure include visible cracks, melted spots, or air/lint leakage around the duct area

• Disconnect power; for gas models, turn off the gas supply
• Access from the front by removing the top and front panel
• Note fastener locations and any attached brackets/harnesses, then transfer them to the new assembly
• Vacuum lint from internal ducting and verify seals before test run

This guide assembly is a replacement slide guide that helps support and align moving components for smooth operation and reliable engagement. It restores proper tracking and reduces wobble or binding in the mechanism. What it does:

• Provides stable support and alignment for a sliding component to prevent mis-tracking and uneven movement
• Reduces noise, sticking, or binding caused by worn or damaged guides
• Helps maintain proper clearance and engagement of the moving part
• Matches OEM fit and mounting points for direct replacement

• Turn off and unplug the appliance before beginning any repair to avoid electrical shock
• Remove any obstructing panels or components to access the guide
• Inspect mating parts (slides, rails, fasteners) and replace any damaged hardware to ensure correct fit

This adjustable leveling leg screws into the dryer base to support and stabilize the cabinet. Replacing a worn or missing foot helps level the appliance, reduce vibration and noise, and keep it steady on uneven floors.

• Provides threaded height adjustment to properly level the dryer
• Stabilizes the cabinet to minimize rocking, vibration, and walking
• Replaces a broken, worn, or missing foot
• Common symptoms: dryer wobbles, is hard to level, or makes rattling/vibration noise

• Disconnect power; shut off gas supply for gas models
• With a helper, carefully tilt or raise the dryer for access
• Unscrew the old leg; thread the new leg into the base by hand, then adjust with a wrench until the dryer sits level and stable
• Ensure all legs contact the floor and the dryer does not rock

This power cord assembly supplies AC power to the appliance and restores safe operation after a damaged or faulty cord. It replaces the worn or frayed factory cord so the appliance can power on reliably. What it does

• Provides the main AC connection between the appliance and household power
• Replaces cords with visible damage, exposed wiring, burnt connectors, or intermittent power
• Helps stop arcing, sparking, or overheating caused by a failing cord
• Fits into the appliance's cord terminal block for a direct, plug-in power connection

• One power cord assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Tighten all terminal screws securely and route the cord away from sharp edges and moving parts

The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.

Symptoms of a bad Dryer Thermistor include:

• Clothes not drying properly or taking longer than usual to dry.
• The dryer repeatedly stopping during a cycle.
• Error messages appearing on the dryer's display panel.
• The dryer getting too hot or not heating enough.

Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.

This OEM LG part can also be used on Kenmore/Sears appliances. 

The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.

Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.

Symptoms of a bad dryer blower thermostat include:  

• The dryer not heating up properly or taking longer to dry clothes
• The blower motor failing to turn on or running continuously
• Inconsistent or inadequate airflow during the drying cycle
• Error codes or fault indicators related to the thermostat or blower motor

This OEM LG part is also compatible with Sears/Kenmore models.

The Motor Bracket is an OEM part for LG dryers. This bracket securely holds the dryer motor in place. It maintains proper alignment and spacing of the motor to allow for smooth operation of the tumble cycle.

Causes of a bad motor bracket can include cracks or breaks developed over time from repeated use and vibration, or damage due to impact or improper installation.

Symptoms of a bad motor bracket include:

• Excessive noise or grinding sounds emanating from the motor area
• The dryer not rotating or tumbling clothes properly
• Increased movement or shaking of the motor
• Poor airflow and inefficient drying performance

This OEM LG part is also compatible with some Kenmore models.

The Drum Motor Assembly is an OEM part for LG dryers. It serves as the powerhouse that drives the drum, enabling it to tumble clothes during the drying cycle. This essential component ensures your dryer operates smoothly, providing the necessary torque for consistent and efficient drying performance.

Causes of failure might include wear and tear from prolonged use, overload from trying to dry heavy loads, electrical issues like short circuits, or physical damage to the motor components. 

Symptoms of a bad Drum Motor Assembly include:

• The dryer drum fails to turn, even though the dryer powers on.
• Unusual noises, such as humming or buzzing, indicating the motor is struggling.
• The dryer stops unexpectedly during cycles or won't start at all.
• Decreased drying efficiency or clothes taking longer to dry due to inconsistent drum speed.

This OEM LG part is also compatible with Sears/Kenmore.

This clamp secures hoses, tubing or wiring to the appliance frame to help prevent rubbing, vibration and routing issues. It restores a solid attachment point so lines stay in place during normal use. What it does:

• Holds a hose, tubing or wire bundle in place to prevent chafing and abrasion
• Keeps components routed away from moving parts and hot surfaces
• Reduces rattling or vibration caused by loose lines
• Helps maintain safe, reliable connections by preventing strain on fittings

• Disconnect power and shut off water before servicing
• Use basic hand tools; avoid over-tightening which can pinch hoses or wires
• Inspect adjacent hoses/wires for wear and replace if damaged
• Take photos before removal to ensure correct reinstallation

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

The Idler Pulley Assembly is an OEM part for LG dryers. It plays a critical role in the dryer's drum belt tension system, helping to maintain proper tension on the belt so the drum can rotate smoothly during the drying cycle.

Causes of a bad idler pulley assembly can include wear and tear over time, buildup of lint or debris, or damage from an overloaded dryer. A malfunctioning idler pulley can lead to inefficient drying and potential damage to other dryer components.

Symptoms of a bad idler pulley assembly include:

• Squeaking or squealing noises during operation
• The drum not rotating properly or at all
• The dryer stopping mid-cycle
• The belt slipping or breaking

This OEM LG part is also compatible with Sears/Kenmore.

The Dryer Idler Pulley is an OEM replacement part for LG dryers. It is a critical component that helps guide and maintain proper tension on the dryer belt, ensuring efficient transfer of rotational force from the motor to the dryer drum.

Symptoms of a faulty dryer idler pulley include:

• Squeaking or grinding noises coming from the pulley area
• Visible wear, cracks, or damage to the pulley surface
• Slipping or irregular rotation of the dryer drum

Causes of a bad idler pulley can include normal wear and tear over time, exposure to high temperatures or lint buildup, misalignment or improper tracking, or physical damage from impact or foreign objects.

This OEM LG part is also compatible with Sears/Kenmore dryer models.

This replacement screw secures appliance components in their proper position. Use it to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded. What it does:

• Fastens brackets, panels, or trim to keep assemblies aligned and secure
• Helps prevent vibration, rattling, and gaps from loose hardware
• Restores proper attachment when a screw is lost, worn, or damaged
• Common symptoms: loose panel/handle, misalignment, rattling, or a missing screw

• Disconnect power; shut off water or gas before service
• Match location to the original; start threads by hand to avoid cross-threading
• Use the correct driver bit; do not overtighten (especially into plastic)
• If the original hole is stripped, repair threads before installing the new screw

This self-tapping screw fastens panels, brackets, and internal components in compatible appliances. Replace a stripped, corroded, or missing screw to restore a secure fit and help prevent vibration, rattling, and misalignment.

• Forms/engages its own threads in sheet metal or plastic for a secure hold
• Secures covers, brackets, and assemblies to maintain alignment
• Helps reduce vibration and noise from loose components
• Replace if the head is stripped/broken, threads are worn, or the screw is missing

• Disconnect power and shut off water or gas, as applicable, before servicing
• Match to the original location and hardware; use identical length and thread where specified
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving hole is damaged, repair it before installing the new screw

This drying rack sits inside the dryer drum to hold items stationary while warm air circulates around them. It lets you rack-dry shoes and delicates without tumbling, helping prevent banging and scuffing that can happen when items rotate. What it does:

• Provides a stable platform inside the drum for stationary drying
• Allows heated air to circulate around items while preventing tumbling
• Used for shoes, sweaters, hats, and other items approved for rack-dry cycles
• If missing or damaged (cracked frame, broken tabs, poor seating), you may hear rattling or be unable to rack-dry items

• 1 drying rack

• Disconnect power and allow the drum to cool before inserting or removing the rack
• Insert the rear of the rack into the drum supports, then rest the front edge on the door opening; ensure it is level and fully seated
• Load items evenly and do not overload; use the rack-dry or low-heat settings recommended in your owner's manual
• Remove the rack before resuming standard tumble cycles

The Venting Kit is an OEM part for LG dryers. This part offers flexibility and efficiency in dryer installation and setup, this kit enables side or bottom venting of the appliance, facilitating optimal use of space in your laundry area. It's ideal for situations where the traditional rear venting is not feasible or preferred. 

Causes of venting system issues can include blockages, incorrect installation, or the use of incompatible parts, leading to reduced efficiency and potential safety hazards, such as overheating or fire risks.  

Symptoms of a bad or improperly installed venting system include:

• Extended drying times
• Excessive humidity or heat in the laundry area
• Unusual noises during operation
• Accumulation of lint in and around the dryer

This OEM LG part is also compatible with some Kenmore models.