Parts for Electrolux E23BC78IPSG: 11 - Cooling System Parts

Molded plastic air deflector that directs cold airflow inside your refrigerator. Replace this part if cracked, broken, or missing to restore proper venting.

Refrigerator not cooling properly? This condenser coil assembly removes heat from refrigerant to restore cooling performance and improve efficiency.

Evaporator coil assembly for bottom-mount refrigerators. Installs in the freezer compartment. Replace if damaged, leaking, or insulation is deteriorated.

Freezer not cooling below 32°F or water leaking under freezer? The drier filter removes moisture from the refrigerant system. Soldering required.

Connects your refrigerator to the wall outlet to supply electricity. Replace if the original cord is frayed, damaged, or has exposed wires from wear or moving.

Fix frost buildup on evaporator coils causing warm temps or freezer icing. This defrost heater melts accumulated ice. DIY repair in 30-40 minutes.

Refrigerator not cooling or freezing over? This evaporator coil absorbs heat to keep your fridge cold. Intermediate repair requiring 2-3 hours work.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Replace your refrigerator door gasket to restore a tight seal, maintain proper cooling, and reduce energy costs. Prevents cold air leaks and frost buildup.

Replacement screw for securing panels, components, and assemblies in appliances. Needed when original screws are stripped, lost, or damaged during repair.

Fix a warm fridge or iced-up freezer coils with this defrost thermostat. Controls defrost cycles to prevent ice buildup. Simple 10-minute DIY repair.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Secures the compressor to the mounting bracket in your refrigerator or freezer. Replace if missing, stripped, or corroded during compressor service.

Replacement defrost drain pan that collects and channels meltwater from the automatic defrost cycle. Replace if cracked, warped, or missing to prevent leaks.

Refrigerator not cooling or running constantly? This compressor with inverter restores proper cooling. Advanced repair requiring refrigerant certification.

Compressor not running but fan works? This inverter control board restores cooling when the compressor fails to start. Moderate DIY with video guide.

Rubber grommet that cushions and protects door components in your refrigerator. Replace if cracked, worn, or missing to restore proper door function.

Secures panels, brackets, and assemblies in refrigerators and freezers. Replace missing, stripped, or damaged screws to restore proper fit and alignment.

Secures and protects wiring harness from strain damage. Replace if cracked, broken, or wires show wear. Verify fit with your model number listed.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Refrigerator harness retaining clip secures wiring in place. Replace if broken or loose to prevent wire damage. Confirm fit with your model number.

Refrigerator completely dead or showing error codes? This main power control board restores central functions. Moderate difficulty repair for most DIYers.

Refrigerator door guide channel that helps align and support the door mechanism. Replace if cracked, broken, or worn to restore proper door alignment.

Replacement mounting screw secures panels, brackets, and trim inside refrigerators and freezers. Restores factory assembly when original fasteners are missing.

Positions the condenser fan and motor in the rear machine compartment. Replace if cracked, warped, or damaged to restore proper airflow direction.

Refrigerator not cooling or making loud grinding noise? The condenser fan motor drives airflow to cool refrigerant. DIY repair in 30-60 minutes.

Refrigerator not cooling properly? A damaged condenser fan blade prevents airflow over the condenser coils. Quick DIY fix—simply push into place.

Secures the evaporator or condenser fan shroud to the refrigerator cabinet. Replace this mounting screw if stripped, missing, or broken during repair.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Metal rivet fastener permanently secures panels, brackets, and internal components in refrigerators. Replace damaged, missing, or worn rivets to restore fit.

Channels defrost water from the evaporator to the rear drain pan. Replace this tube if it's cracked, clogged, missing, or has become brittle over time.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Water leaking from tubing connections or no water to dispenser? This tube connector joins refrigerator water lines to restore secure flow to your icemaker.

Fixes incorrect temperature readings and short cycling. This thermistor monitors fridge temps and signals the control board. Moderate DIY repair.

Wiring harness that connects the control board to internal components in your refrigerator. Replace if harness is damaged, frayed, or corroded.

Refrigerator not cooling or freezer warming up? The heat exchanger manages refrigerant flow in the sealed system. Professional installation recommended.

Wiring harness for refrigerators. Connects electrical components inside the unit. Replace if wires are frayed, connectors are damaged, or melted.

Protects wiring harness edges in your refrigerator from wear and abrasion. Replace if cracked, broken, or missing to prevent wire damage and insulation.

Foam seal tape creates airtight barriers around refrigerator components. Replace when worn, compressed, or damaged to restore proper sealing and efficiency.

Connects dispenser controls and components in the refrigerator door. Replace if the wiring is damaged, frayed, or causing intermittent dispenser operation.

Fixes incorrect temperature readings and excessive frost buildup in refrigerators. This sensor monitors air temperature to control compressor cycles.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

Replacement mounting screw for refrigerator panels, handles, brackets, and internal fixtures. Order when original screws are stripped, lost, or damaged.