Craftsman Chainsaw Parts

Fix a chainsaw that won't pull-start or has a broken recoil cord. This starter pulley connects the recoil mechanism to engage the engine during starting.

Replacement spring for chainsaw ignition switches. Installs inside the switch assembly. Needed when original spring is broken, worn, or missing.

Prevents contaminants from entering your chainsaw's carburetor. Replace when clogged with dust, pollen, or debris to maintain proper air-fuel mix. Verify fit with your model's parts diagram.

Flexible intake tube that connects the adapter to the carburetor on gas chainsaws. Replace if worn, cracked, detached, or missing to restore proper fit.

Replacement assist handle for line trimmers. Mounts to the shaft to provide steering control and grip during operation. Replace if cracked or broken.

Protective cover that secures the air filter on your chainsaw. Replace if cracked, broken, or missing to prevent filter damage and debris entry.

Chain overheating or not staying oiled? This oil pump kit delivers consistent lubrication to prevent chain damage and ensure safe operation. DIY fix.

Designed for use with a wide range of string trimmers, this momentary switch is a genuine OEM replacement part. A momentary switch, also known as a kill switch, is a safety precaution that kills an appliance's engine in a moment, even if the engine is not set to the off position. This helps prevent accidents if the operator begins to lose control of the trimmer. At the touch of a button, the engine cuts and cannot be restarted for a short period (usually about five seconds). Momentary switches are positioned in a way that they don't often sustain damage but, over time, they can wear out. Once a switch stops working, it will need to be replaced to ensure safe operation. This is a fairly straightforward fix that only requires a screwdriver to open the tiller's handle and pliers to safely remove the wiring. This part is designed for string trimmers made by Poulan, Weed Eater, Paramount, and Husqvarna. It ships individually of any other hardware is comes sourced from the original manufacturer.

Internal engine component that moves within the cylinder to drive the crankshaft. Replace when worn, burnt, cracked, or causing low compression issues.

This product is the chainsaw's engine cylinder, which holds fuel ignited by the spark plug. It fits into the existing chamber and houses the pistons during use. It is attached to the carburetor for fuel injection. The spark plug is set within it to ignite the fuel. This part has to be screwed securely into place prior to use and requires lubrication for the engine to run smoothly. If the engine suffers from poor fuel ignition, or leaking fuel, the cylinder may be cracked. When installing the new part, a few holes may require a tap to fit each specific machine. Pistons and bolts sold separately. Existing parts should be cleaned prior to use. This OEM replacement part is sourced straight from the manufacturer and works with certain models of Poulan and Husqvarna small engines.

Chain won't stop when brake is engaged? This chain brake kit tightens around the clutch drum to stop the chain immediately on kickback. Moderate install.

Complete gasket set for chainsaws seals engine components during motor service or repair. Replace when servicing engine to prevent fuel leaks. Verify fit.

This carburetor is designed to mix gas and oil together before moving the mixture into a chainsaw's engine. It is a single-cylinder model with an auto-choke system and requires regular maintenance to stay in good shape. Changing the oil, replacing the air filter, and adding a fuel stabilizer will help keep the engine performing at its best. If the carburetor isn't working properly, this may be due to blockages of debris, dirt, and fuel. If the fuel tank is full but the engine refuses to start, it's a good idea to test the carburetor for problems. Take out the air filter and then pour a small amount of fuel into the carburetor itself. Yank on the starter rope and see if the motor starts. It should die shortly after. If this occurs, the carburetor may have a problem and require replacement. This is an individual part that is compatible with Poulan, Craftsman, and Husqvarna chainsaws. The carburetor is a genuine OEM product that is provided directly from the manufacturer. It comes with a rubber O-ring and a gasket. A screwdriver will also be required to make a replacement.

Replacement oil cap for chainsaw, trimmer, and pruner oil tanks. Tethered design prevents loss. Replace if cracked, broken, or missing threads.

Mower won't stop or squeals when braking? This brake pad creates friction against the rotor to safely stop your riding mower. Direct replacement part.

Left-hand stationary idler pulley for riding mowers and lawn tractors. Replaces cracked, worn, or broken pulleys affecting belt routing and tension.