Crosley Cooktop Parts

We ordered the parts we needed, and received it with-in a week. My husband was able to covert the stove in one evening. Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more

We ordered a igniter and a new regulator. My husband installed the parts it works great now. Read more

DIY. The delivery to Milwaukee took two days. The project was very easy and took about 1hr. The only tools required were a screw driver (electric) and a pliers. Just make sure your irganized with the screws so you don't lose any or mix up which ones go back in which holes. There's about 20 total screws. This $50 part saved me from having to buy my wife a $1000+ oven. Read more

I tried swapping the cables around by putting the cables from the burners that would light onto the ones that didn't light. When I did that the problem would move. So this is how i determined that the issue was with this module and not the burners or cables. Once this new module arrived it was simple to disconnect the old one and put the cables back on the new one. I tested it (holding by breath!) and then all of the burners started. HOORAY! Read more

• Takes too long to dry

Get some acetone at a Hardware Store before you start. A pint will do. Unplug the dryer from 110 VAC. Pull the top off of the dryer, by lifting it from the front first. It is attached with snap metal fittings. Do not completely remove the top, just tip upright to gain access to the front interior of the dryer. Before you pull any wires from the door switch, record which color wires go to which terminals on the door switch. If you reassemble the connections incorrectly, the gas value will... Read more

• Element will not heat

Personally I have experience working with electricity and knowing if I bought the part required this would be an easy fix. I got my model number and contacted Appliance Parts Pros and placed my order for the new elements, terminal blocks, and for appearance purposes 4 new Drip Pans. Excellent service and quick shipping. I ordered my parts on Sunday and received them on Tuesday. This was a simple repair that only required a screwdriver to remove the old terminal block from the range hood, wire... Read more

Ordered replacement parts Read more

Ordered new Ignitor / Orifice and screws Mike was a great resource, he helped me thru the project. Read more

I ordered the correct part from AppliancePartsPros.com. When I received it, I opened the package and identified the parts I would need for my application. I cleaned up around my work space, then turned the power off to the appliance. I removed all the burners to get to the mounting screws for the range top. I then lifted the range top and supported it so I could see what I was working on . I first inspected all the wiring for breaks, or fraying. Then I moved on to the switch. Two screws... Read more

Bought name brand parts to match the stove brand. The fit was perfect and have never had an order arrive the next day from ordering it. Read more

Replaced spark module - oven was less than two years old. Like a lot of new gas ovens, turning on any one burner to 'lite' sends sparks to all 5 top burners. The difficulty was getting to the spark module, as some generic videos show access to it from the upper panel on the back of the oven, but it wasn't there. Had to take off the entire top burner panel of the oven to get to the module, and then it was simple to replace the module by transferring the wires to the new one. I did see on... Read more

• Oven is too hot
• Little to no heat when baking

Removed old thermostat and pulled old thermocouple fron oven. ran new thermocouple to oven and put in clip, tistalled new thermostat using 2 phillips head screws, done. Read more

• Little to no heat when broiling

I had the choice of spending $2K on another double oven stove or $60 on two elements. (I felt more secure about replacing both bake and broil elements just in case the fire had damaged the bake element) It was an easy decision and quick replacement! Power was already off to the stove so I cleaned up the fire retardent mess. I even found easy instructions dismantling the oven door in order to clean the powder residue from between the glass. I then removed the rack and remaining old elements. I... Read more