Crosley Igniter

• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

My Kenmore 790.74139310 gas range was taking over 30 minutes to reach 350F. It used to take a little less than 10 minutes. The problem was the ignitor for the lower gas burner. It would glow but not pass sufficient current to increase the gas flow to the lower burner. Once at temperature, there is of course loss of heat when loading the oven with room temperature food. This took too long to recover, so we did not have proper temperature for proper cooking for the first 30 to 40 minutes. Food... Read more

Replaced igniter. Problems solved. Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Gas smell
• Little to no heat when baking

I used the little video clip shown under the part and replaced it myself. Read more

• Little to no heat when broiling
• Gas igniter glows, but will not light
• Little to no heat when baking
• Gas smell

Followed linked video instructions and replaced with new flat style Oven Igniter Kit. Some repair info background, while out shopping for a replacement oven ($1000 plus) a terrific salesman listened to the issue with my current oven and recalled his same issue and solution. I thanked him for his time and recommendation. I went home and searched "oven Ignitor" where I was led to this website. The video showed the same exact flat oven igniter and how easy it would be to replace it. I immediately... Read more

Replaced ignitor. Very simple project. Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

After verifying the no heat problem myself, I just googled "LG3412W no heat" with my smartphone and thumb. One of the first hits was the Appliance Parts Pros website with a list of 8 possible parts that might fix this problem, listed in descending order of likelihood of success. With 3 adults worth of dirty laundry piling up and straining our ability to drip dry, I had to agonize over: 1) buying a new dryer from whatever a local dealer had in stock, then clearing years of valuable junk in... Read more

I looked on Appliance Parts Pros. com and read the problems that others had and replacing the ignitor made sense so I ordered one. It came by UPS within 3 days. I watched the video on how to replace it. Everything went easily, except the screw that held the ignitor in place was a philups head screwdriver and I couldn't get a screwdriver into the small space I had to work in so I went to Harbor Freight Tools and bought an inexpensive 90 degree rachet screwdriver for $2.99 and it worked great.... Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

We ordered a new ignitor and it came in two days just as promised. The only problem that we experienced was that the leads on the new ignitor were to short. We were able to find enough slack on the oven end to make it work. The oven is once again working great. The video was a little off on what need to be done to disconnect the ignitor. We actually had to flip the oven over to get to the bottom. We could not access the connector through the back. Read more