Dryer Duct Parts

This side vent kit restores a finished side vent opening and directs exhaust airflow for proper ventilation. It replaces damaged or missing vent trim to help reduce drafts and visible gaps around the vent. What it does:

• Provides the exterior vent trim and mounting interface so the appliance exhaust vents cleanly to the side
• Restores a finished appearance where the vent exits the cabinet or wall
• Helps stop outside air from entering through a damaged or missing vent opening
• Can reduce rattling or noisy airflow caused by loose or broken vent trim

• Disconnect power to the appliance before attempting service and follow all safety guidelines
• Basic hand tools are typically needed; follow the appliance's service manual for specific instructions
• Use the OEM installation instructions and hardware
• Check the vent path and seal after installation to ensure proper airflow and fit

This Vent Adapter is an OEM part for Bosch Dryers. It plays a role in connecting the dryer exhaust to the vent hose, ensuring efficient airflow and proper ventilation. Over time, wear and tear or improper installation can lead to issues with this component.

What Causes a Bad Vent Adapter: 
Continuous use or improper fitting can cause the vent adapter to degrade or become loose. Exposure to heat and moisture from the dryer can also contribute to its deterioration.

Symptoms of a Bad Vent Adapter:

• Poor dryer performance
• Difficulty in connecting the vent hose
• Air leaks around the vent connection

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This parts assembly is the factory replacement service assembly that houses and connects the appliance's internal components, restoring proper electrical and mechanical function when a worn or damaged assembly causes failures. What it does

• Replaces a damaged or worn internal assembly that can cause control failures or intermittent operation
• Restores secure electrical and mechanical connections between internal components
• Helps resolve symptoms like no power to controls, erratic operation, or components not responding
• Matches OEM fit and form to maintain original performance

• Intended for technicians or experienced DIYers; disconnect power before starting any repair
• Handle with care to avoid damaging connectors, wiring, or delicate components
• Reuse existing mounting hardware unless replacements are specified
• Test appliance function after installation and secure all panels before restoring normal use

Compact 90-degree elbow for appliance hookups in tight spaces. This close-clearance fitting lets you turn the connection right at the outlet, allowing the unit to sit nearer the wall while maintaining a secure, reliable joint.

• Provides a tight 90-degree turn where clearance is limited
• Helps align the appliance connection with the supply/outlet without kinking or undue stress
• Replaces a bent, cracked, stripped, or leaking elbow
• Can help address fitment issues or leaks at the connection point

• Disconnect power and shut off the applicable supply (gas, water, etc.) before servicing
• Use only an appropriate, approved sealant or gasket as specified by the manufacturer
• Restore service and check for a secure, leak-free connection after installation

This out exhaust pipe directs a dryer's exhaust airflow from the appliance to the home vent, helping remove moisture and lint from the dryer cabinet. Durable replacement for worn or damaged exhaust tubing. What it does:

• Channels hot, moist air from the dryer to the external vent to prevent moisture buildup
• Helps maintain proper airflow for efficient drying and reduces lint accumulation inside the cabinet
• Replaces cracked, crushed, or disconnected exhaust connections that cause poor venting or air leaks
• Works as a direct-fit plumbing piece when original exhaust piping is damaged

• One out exhaust pipe

• Disconnect power to the appliance before installing; for gas dryers, turn off gas supply and pilot per manufacturer instructions
• Ensure the pipe fits securely to the dryer outlet and the wall vent; use manufacturer-recommended clamps or fasteners
• Inspect and clean the vent path and lint screen while replacing the pipe to ensure safe airflow

This elbow is a molded hose connector that redirects fluid or airflow in the appliance, restoring proper routing for drainage or vent lines. It helps stop leaks and maintains correct hose alignment for reliable operation. What it does

• Redirects hose or duct routing at an angle to fit tight spaces
• Restores a secure connection where a cracked or broken elbow causes leaks
• Helps prevent kinks or pinched hoses that can cause poor drainage or reduced airflow
• Supports proper sealing when used with the correct clamps or gaskets

• One elbow connector

• Disconnect power and shut off water before replacing the part
• Inspect mating hose ends and clamps; replace damaged hoses or clamps for a secure seal
• Ensure correct orientation and fully seat the elbow before tightening clamps
• Do not force the part into place; confirm fit and alignment to avoid stress or leaks

This blower housing encloses the dryer's blower wheel and routes air from the drum through the lint system to the exhaust. Replacing a cracked or warped housing restores proper airflow, reduces vibration, and helps resolve extended dry times.

• Encloses and supports the blower wheel while channeling intake and exhaust airflow
• Helps maintain consistent drying performance and temperature regulation
• Typical failure symptoms: longer cycles, weak vent airflow, excess lint inside the cabinet, scraping or rattling near the blower
• Visual clues: cracks, broken mounting tabs, or housing out-of-round causing wheel contact

• Disconnect power; for gas units, also shut off the gas supply
• Access from the front: remove front panel and lint duct to reach the blower assembly
• Transfer the blower wheel, gasket/seals, and mounting hardware from the original housing as needed
• Seat the housing squarely; the blower wheel spins freely and clear lint buildup before reassembly

This wall elbow redirects the dryer vent through a wall opening, keeping the exhaust path secure and aligned for safe, efficient venting. Replaces a worn or damaged elbow to help restore proper airflow. What it does

• Provides a finished transition from the dryer vent pipe to the wall recess.
• Helps maintain a sealed vent path to reduce air leakage and lint buildup.
• Common fix for a cracked, loose, or broken elbow that causes noisy or inefficient venting.
• Works with standard dryer vent systems where a recessed wall box is used.

• Designed for use with compatible dryer vent housings;
• Turn off and disconnect the dryer before servicing; wear gloves to protect hands from sharp metal edges.
• Inspect surrounding venting and clear lint before final assembly to improve airflow and safety.

This 5-foot flexible vent hose provides a replacement vent path for your dryer, restoring proper airflow to help clothes dry efficiently and reduce lint buildup. It's a straight, flexible vent designed for inline dryer ducting. What it does:

• Channels hot, moist air from the dryer to the home vent outlet to help shorten drying cycles
• Helps prevent lint accumulation in the dryer exhaust path when properly installed and maintained
• Can resolve symptoms like longer dry times, reduced airflow from the dryer, or overheating due to restricted venting
• Works as the inline connector between the dryer outlet and the household vent opening

• One 5 ft flexible dryer vent hose

• Disconnect power (and gas supply for gas dryers) before replacing the vent; follow all safety precautions
• Ensure the hose is not crushed or kinked and has a smooth path to the exterior vent for best performance
• Use proper clamps or fasteners to secure both ends and check for leaks after installation
• Clean lint from the dryer and duct before installing the new hose to maximize airflow

This dryer elbow is the molded duct connector that redirects exhaust from the dryer to the vent duct, helping restore proper airflow and reduce leaks around the outlet. It's a simple replacement for a cracked or loose elbow. What it does:

• Connects the dryer's exhaust outlet to the home vent duct to direct hot, moist air outside
• Replaces cracked, broken, or warped elbows that cause air leaks or rattling
• Helps reduce lint escape and improves exhaust path integrity when fitted properly
• Can eliminate visible gaps or misalignment at the dryer outlet

• One dryer elbow part

• Disconnect power (and gas supply for gas dryers) before servicing; follow all safety warnings
• Remove the dryer from the wall enough to access the outlet; loosen or remove clamps to swap the elbow
• Use appropriate duct clamps or approved tape to secure connections; ensure vent is clear of lint

The Steam Hose Kit is an OEM part for Frigidaire dryers. It provides the necessary conduit for steam from the water source to the dryer. The kit includes: 
5’ Rubber Fill Hose with Gooseneck
1’ Rubber Fill Hose (Female/Female)
All Male Y Connector

Causes of a bad steam hose can range from normal wear and tear to improper installation or physical damage from external sources.  

Symptoms of a bad Steam Hose Kit include:

• Leaks or drips from the hose connections.
• Reduced steam output, affecting the dryer's ability to effectively remove wrinkles or sanitize clothes.
• Noticeable wear or damage to the hose, such as cracks or splits.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

(18"- 29")