Electrolux Wall Oven Parts

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

Replaced ignitor. Very simple project. Read more

I first felt along each heating element (bake and broil) hoping to find a rough or blistered place on them. But they were both smooth with no irregular places. (replacing the elements would have been the easiest and cheapest repair. Pulled the back off the range (unplugged, of course) - checked wiring. There were no loose connections or burned wiring. I disconnected the elements and checked them with a ohmmeter (VOM) and both had continuity. Discovered that both elements used the same... Read more

I have used this site before to fix my dishwasher, so I knew to check here first. I searched other's comments to troubleshoot my problem. Ordered the part and it arrived in only a couple of days. I should insert here that I am a 45 yo female, so if I could do this, anyone can. I watched the video and proceeded to replace the part. For my particular model, I didn't access the part from the back, but instead through the underside by removing the bottom drawer. Total from start to finish... Read more

• Element will not heat

Replacement of the element was relatively straightforward, but there are a couple of things to be aware of before you begin. First, turn off power to the stove at the breaker box. Allow the cooktop to raise by removing the two screws that secures it on the underside of the front edge. Open the oven door to do this. Removal of the old element is simple, just remove the two screws that secure the wide mounting bracket that holds the two front elements. Carefully turn the assembly over. To... Read more

• Little to no heat when baking

Replaced with new Read more

Finding the proper conversion kit was a snap. I just plugged in the model number and Appliance Parts Pros sent the proper conversion kit. Read more

We are very inexperienced appliance repair people. Thus check it out first to see if we can fixit...successs. First checked to be sure it wasn't the actual switch. Did this by numbering the wires and then switching the two switches b/w the right and left front dual burners. Success, the switch was fine but kinda disappointed cause this part was less expensive. Proceeded to then order the left front dual burner. Arrived in a few days, packed well. We unplugged the appliance, as it been a... Read more

Removed the bake element and broil element. Tested them with a multi meter. They failed. Ordered new elements. Received them in 2 days. Installed new elements. Oven works great. Entire fix took 10 minutes to remove and test elements, 10 minutes to install the new elements. It was my first time working on an appliance, the instruction videos were great! Read more

I ordered this glass and used a youtube video to replace the shattered glass step-by-step. I was a bit wary of doing this work myself, but it proved to be a snap. Within an hour of finding this package on my front porch, I had the oven as good as new. Read more

• Element will not heat

Replaced burner switch and all was working properly. Great customer service and part replacement. Read more

Ordered on Wed, received on Fri. Took less than 5 minutes to replace all 4. No tools needed. Read more

• Element will not heat

Very easy. go online learn how to change the element step by step. order the part and you are all set. I saved $99 of labor cost. Read more

• Little to no heat when baking
• Won't start

We replaced the broken Terminal Block but have not yet replaced the Control Panel. Will purchase that part from you shortly. Read more

My old White Westinghouse stove has easy replacement of the elements & drip pans. They literally pop in & out with no effort or education necessary. Read more

Unplugged stove. Removed six 1/4 inch socket head screws from back panel. Removed back panel. Removed plug on the back of the OCB. Removed OCB. Used Philips screwdriver to remove four mounting screws (and cracked pieces of the mounting holes). If you can get to this point, installing the new OCB is pretty self explanatory. Read more