Estate Dishwasher Parts

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.

Wire harness elbow connector for dishwashers. Replaces damaged, cracked, or broken electrical connectors that route power between components.

Standing water in dishwasher bottom or leaking onto floor? This impeller and seal kit repairs worn bushings and seals. 15-minute DIY fix.

The Dishrack is an OEM replacement part for Whirlpool dishwashers. It measures 21" wide x 21" deep. It provides a stable framework for organizing and holding dishes, glasses, utensils, and other items during the washing cycle. Designed to fit securely in the dishwasher, it ensures proper water flow and cleaning efficiency for all loaded items.

Causes of a bad Dishrack can include prolonged exposure to high temperatures and moisture, leading to rust or corrosion, damage to the coating from sharp utensils, or bending or breaking due to heavy or improperly loaded items. Over time, these issues can compromise its functionality.

Symptoms of a bad Dishrack include:

• Rust or peeling coating on the rack
• Broken or bent tines that can’t hold dishes properly
• Difficulty sliding the rack in and out of the dishwasher

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Fix leaks around the dishwasher motor or poor spray pressure with this impeller and seal kit. DIY-friendly repair takes about 2 hours with basic tools.

Fix water leaking from under your dishwasher with this pump volute. Directs water flow and prevents leaks with integrated seal. 20-minute repair.

Third level wash arm assembly for dishwashers. Installs on upper feed tube in top rack area. Replace if disc is cracked, washer is missing, or assembly won't stay on shaft.

Color: white. Measures about 3 inches wide by 4 inches high by 10 inches deep.

Fix dishwasher overflows or won't fill issues. This water level float detects proper fill levels. Replaces broken or stuck floats causing drainage problems.

This door catch and strike work together to keep the door securely closed and engage the safety interlock switch. Replacing worn pieces restores a firm latch and reliable operation when the door is properly shut.

• Aligns and engages the latch so the door stays closed during operation
• Activates the door switch so cycles can start
• Helps prevent the door from popping open mid-cycle
• Common symptoms: door won't latch without force, unit won't start, visible wear or a bent strike

• Disconnect power to the appliance before servicing
• Open the door and remove mounting fasteners to swap the catch and strike
• Adjust strike alignment/depth so the latch engages fully and the door sits flush
• Restore power and test for smooth closing and proper cycle start

Outer door panel for dishwashers. Installs on the front of the dishwasher door. Replace if scratched, dented, or to change color finishes.

Touch-up paint for restoring chips, scratches, and nicks on painted appliance surfaces. Covers minor cosmetic damage on exterior panels and finishes.

This drain impeller spins inside the drain pump to move wastewater out of the appliance, restoring normal draining and reducing standing water. It's a direct-replacement pump impeller designed to fit the original pump housing. What it does:

• Drives water through the drain pump so the washer can empty properly
• Worn or broken impellers can cause slow or no draining and standing water
• May produce unusual pump noise or vibration when damaged
• Helps prevent motor overload by maintaining proper water flow

• One drain impeller

• Disconnect power before accessing the pump assembly to avoid electric shock
• Inspect the pump housing and fasteners; replace any damaged clips or seals as needed
• Reassemble pump and test a short drain cycle before completing the repair

This is a genuine replacement screw used to secure components and panels on compatible Whirlpool appliances, restoring a firm, vibration-free fit. It replaces worn or missing fasteners to help keep parts aligned and stable. What it does

• Secures panels, brackets, or internal components to prevent shifting or rattling
• Replaces stripped, rusted, or missing screws that cause loose parts or noise
• Helps maintain proper alignment of mounted components for safe operation
• Useful when reassembling repair work or after removing parts for service

• One replacement screw

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power before servicing electrical appliances; follow OEM safety guidance
• If screw threads or holes are damaged, replace both screw and mating hardware as needed

Replacement outer door panel for your dishwasher. Installs on the front exterior of the door. Order when your panel is cracked, dented, or damaged.