Estate Gasket & Seal

This heat-resistant fiberglass oven door gasket seals the oven cavity perimeter, helping keep heat inside for consistent temperatures and efficient cooking. Replace a worn, frayed, or flattened seal to restore proper door sealing performance. What it does

• Forms a heat-resistant seal around the oven opening to minimize heat loss
• Helps maintain set temperature and overall cooking performance
• Can help address long preheat times, uneven baking, and hot air leaking around the door
• Replace if the gasket is frayed, brittle, compressed, or falling out of its channel

• Includes: 1 fiberglass door gasket

• Disconnect power and allow the oven to cool completely before service
• Remove the old gasket from its mounting slots or clips; clean the channel of debris
• Install the new gasket without stretching; seat it evenly around the perimeter with ends routed as originally positioned
• Close the door and check for uniform contact all around; adjust seating if needed

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.

• Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
• Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
• Helps limit condensation or musty odors from trapped moisture inside the door panel
• Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation

• Disconnect power and turn off water supply before servicing the dishwasher
• Remove the inner door panel to access the vent assembly
• Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
• Reassemble and run a short test cycle to check for leaks at the vent area

Located between the console and door

This vinyl door seal lines the perimeter of the appliance door to help block air and moisture leaks, cushion the close, and maintain proper operation. Replace a worn seal to restore a tight, quiet, reliable door closure.

• Creates a continuous seal around the door opening to reduce leaks
• Helps contain air and moisture and dampens door vibration
• Replace if the seal is torn, cracked, flattened, or coming loose
• Symptoms include gaps or drafts at the door, noise, or visible wear

• Disconnect power; for gas appliances, also shut off the gas supply
• Remove inner door panel/trim as needed to access the seal area
• Remove the old seal and clean the mounting surface of residue
• Install the new seal without stretching; if your model uses adhesive, apply per instructions and allow proper cure time

This oven door gasket fits select 30-inch models and restores a tight, heat-resistant seal between the door and oven cavity. Replacing a worn gasket helps contain heat, support accurate temperatures, and protect surrounding surfaces from excess heat.

• Maintains a thermal barrier to keep hot air inside the oven cavity
• Helps the oven reach and hold the set temperature
• Reduces heat escaping around the door for more consistent baking
• Replaces gaskets that are cracked, frayed, flattened, or leaking; common symptoms include long preheat times, temperature swings, or feeling heat escaping at the door edge

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the old gasket from the frame, noting the orientation of any end clips or pins
• Clean the frame/channel to remove debris for a proper seal
• Install the new gasket without stretching; seat clips/pins fully and check for even contact all around

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

This door gasket seals the broiler/bottom-oven door to help retain heat for more even broiling and reduce stray heat into the kitchen. It replaces worn or damaged seals that allow heat loss or uneven cooking. What it does:

• Creates a heat-tight seal around the broiler/bottom-oven door to improve cooking performance
• Helps prevent heat loss, uneven broiling, or extended cook times caused by gaps in the door seal
• Wear signs include visible cracks, flattened or torn material, and gaps around the door edge
• Replacing a damaged gasket can reduce smoke from burning food debris caught in a torn seal

• Disconnect power (and gas, if applicable) and allow the appliance to cool fully before starting
• Remove the broiler drawer or door per the owner's manual to access the gasket channel
• Clean the gasket channel of debris before seating the new gasket; press the gasket into the retainer evenly

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method