Estate Microwave Parts

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

Replaced bulb and socket. Install new grease filters, easier than cleaning. Read more

First, just for safety sake, unplug the unit. I took the three screws out of the latch end of the door and pried both the inner (black) frame off and the outer (white frame) being careful not to crack the inner frame as I wanted to reuse it. I removed the screws holding the old handle on and reused them to fit the new handle to the new frame. I then had to take the glass from the broken frame, clean it, and reuse it on the new frame. You need clear silicone sealer to hold the glass firmly in... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

• Door won't close

My microwave was stainless steel. I ordered the part for stainless steel, but it was not identical in color. It was black and not the gray color of stainless steel. However, I removed the stainless steel (the actual metallic) frame from my broken grille (bent back a few metal tabs and pried loose the adhesive tape with a putty knife). Then I placed it on my new black plastic part and reassembled to the microwave. I find that it looks perfectly acceptable and maybe even nicer with the black as... Read more

Obtained the replacement motor and tray coupler from Appliance Parts Pro. Video of the typical replacement was very helpful to show what to expect and how to replace the motor and coupler. The removal of the bottom plate was held in place by several phillips screws. The motor was attached with two torx screws. The electric connection clips to the motor required needle nose pliers to pull them off. The tray coupler was simple to install after the motor was secured and bottom plate was replaced.. Read more

Followed the instructions. Easy... Read more

• Won't start

First, it was going to cost $95 for an appliance guy just to look at it! I figured there would be an upcharge on the parts + labor on top of the $95, so I took a chance & decided my husband & I could fix it cheaper; we were right, but it was a 3 week process (luckily, we have another microwave in the basement we were able to use in the meantime). I googled the microwave model #, then price checked the same item I thought we needed; printed off the diagrams of the various microwave "systems" &... Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

I was given a very nice microwave, but when it came time to install I was missing a couple screws and the grill was broken. I went online and located the missing or broken parts. I ordered them and was shocked when two days later it was on my porch. This was no doubt the fastest and best ordering experience I've ever had. Read more

Looked Up video. Made job easy! Read more

We found the parts on this website. Thanks to your search bar, we could see if the parts would work on our model microwave. Read more

I took the plastic vent piece off the front of the microwave & removed the charcoal filter & put the new one in. Made sure that while I had it open I cleaned all the built up grease out of it before closing it back up. Took the 2 grease filters from underneath the microwave & replaced with the new ones. Read more

Ordered what was shown on the pc. I removed old ones, put in new ones good to go. Read more

Replaced lower door interlock bracket, cam(which was redesigned), spring(I believe this was the problem) and switch. When the door opens the spring moves the cam which releases the switch"on" Button which turns on the interior light when you close the door, the latch which protrudes out from door pushes into the cam which rotates to turn off the light switch and enables operation of the microwave. Old design cam would push past the light switch and the weakened spring would not push it back... Read more

Ordered your charcoal and stainless steel filters, checked out a YouTube video, et voila!! Slicker than a whistle! Thanks! Read more