Need Help?
Call or text
This is a genuine OEM clamp sourced directly from the manufacturer. It is used in various lawn and garden machines to connect hoses to fittings. It is used to connect piping to water pumps, exhaust pipes to exhaust manifolds, and other similar applications. This connection prevents fluids or air from leaking from the hose. Clamps may be spring or screw/band clamps. Spring clamps require no tools to install and remove; however, the size must be more accurate than when using screw/band clamps. Screw/band clamps are adjustable and can be tightened or loosened. Screw clamps should be inspected periodically to ensure tightness and that the clamps have not rusted.Hose clamps are installed approximately 1/4 inch below the end of the hose. If two clamps are used, there should be 1/4 inch between the two bands. When using a screw clamp, loosen the screw with a screwdriver just enough to fit the clamp over the hose. If using a spring clamp, squeeze the clamp and hold it open. Slide the clamp over the hose and then attach the hose and clamp to the fitting. Slide the clamp into place at the joint and tighten. Do not overtighten. This brass-colored clamp is a spring clamp made of metal; it is sold as an individual unit. This clamp is compatible with many different types of pipes made by various manufacturers.
Usually ships within 4 - 14 days
This part is a carburetor stud. A carburetor mixes fuel and air before delivering it to the engine. The carburetor stud, often called carb stud, is used to ensure a tight seal between the carburetor and the intake manifold. It is important that air and other dirt or debris do not enter the engine, and so this seal between the carburetor and the intake manifold is very important.A carburetor stud may need to be replaced if it is stripped or worn. Of course, a new carburetor stud will be needed if it is missing. If the carburetor and the intake manifold do not have a tight seal, it could be possible that new carburetor studs are needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer. It is sold individually. This specific carburetor stud is compatible with engines, lawnmowers, and log splitters manufactured by MTD, Yard Machines, Yard-Man, Cub Cadet, Husky, and Troy-Bilt.
This part is a replacement screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or misplaced screw in a variety of lawn equipment. This screw is a high-quality piece of standard hardware with multiple different uses. Screws are essential for securing parts of the equipment, but can easily become lost, stripped, or otherwise damaged. If screws are missing, it can affect the functionality of the equipment. A Phillips head or flat head screwdriver can be used to install this screw. It's important when working on or near any engine to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this screw, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this screw is suitable for use on several models of lawn equipment manufactured by Husqvarna, Poulan, and other brands. This is a genuine part made of high-quality, durable metal and is sold individually.
This is a genuine OEM lawn and garden equipment screw that is used in various types of machines. It is a tapping screw that may have several applications depending on the exact equipment in question. A hex key screw is responsible for providing a secure hold for various components. It is made of durable metal, but also exposed to high heat and constant vibrations which can lead to wear, damage, or even breaking. The screw should always be replaced with an OEM replacement. This genuine OEM tapping screw is manufactured by Poulan. It is designed to be used in select outdoor power equipment units from the brand. It can also be used in compatible models from Paramount, Weed Eater, Jonsered, and Husqvarna. It fits trimmers, chain saws, and hedge trimmers from these brands. The tapping screw is sold individually and does not include any additional hardware or parts. A Torx screwdriver or hex key will be required to replace this tapping screw. Be sure to wear gloves when performing engine repairs and allow the machine to cool completely before starting work.
This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.
This washer is used in the steering column of lawn mowers and lawn tractors. It is silver with smooth edges, and it fits bolt shoulders crafted by Husqvarna. Washers are flat pieces of steel used to prevent stripping of bolts and screws.This part is intended to be used in conjunction with a bolt shoulder and bracket deck suspension. Place the washer against the bracket deck suspension and screw the bolt shoulder through the hole in the washer. This keeps the washer in place and creates a buffer between the bolt and the bracket. Failure to use a washer will prevent the bolts from tightening appropriately and negatively impact load suspension. These washers are expertly crafted. Still, washers may need to be replaced due to rusting or corrosion. These issues, combined with regular wear and tear, can cause the washers to fail or break over time.This washer is compatible with numerous mower models and personal use tractors, including Husqvarna, Poulan, Ariens, and Craftsman. This piece fits any model produced by Husqvarna that requires part #532199162. Sold individually. This part is guaranteed, genuine Husqvarna. This is an OEM replacement part sourced directly from the manufacturer.
This replacement part is a clip. This is a genuine replacement part made by Husqvarna. This part is similar to a screw in that it's able to hold many parts together and secure during use so that the engine may run smoothly. This clip is typically found in lawn mowers and is very versatile. A new clip might be needed if the current one is missing or lodged in place. If this is the case it is recommended that it be replaced as soon as possible. A faulty clip can cause other issues in the overall operation of the machine. This should be a fairly simple repair and require household tools. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use. This clip is sold individually and is sourced directly from the manufacturer.
This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.
This part is a replacement retainer ring. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part will replace a broken or misplaced retainer ring on lawn tractors. Retainer rings help to hold components together properly. This ensures that there isn't unnecessary movement, breakage, or friction. This part can become worn or corroded over time and thus will need to be replaced. Wear work gloves to protect the hands when installing this retainer ring. Always ensure that the equipment is completely powered off and is cooled down before attempting to start the repair process. For more accurate information on the installation of this retainer ring, reference the owner's manual or equipment diagrams for specific instructions and part location. This is an authentic OEM part and as such is sold individually and made from durable and high-quality metal. This retainer ring can be used with a variety of different lawn tractor models manufactured by Husqvarna and Poulan.
This 1/4-20 hex nut has a great variety of uses on lawn and landscaping equipment. As a lock nut, it can be tightened and retains its grip, even without the use of a washer. This particular piece of hardware appears in many connective points on push mowers, zero-turn mowers, riding mowers, tillers, lawn tractor implements, and other types of equipment manufactured by Husqvarna, Poulan, Jonsered, and Weed Eater. For instance, with MTD mulching mowers, these hex nuts are used to secure the mower housing to the manifold of the mower. More than just with gasoline-powered lawn tools, these versatile nuts are also found on handheld tools like impact wrenches and tools driven by compressed air. Hex nuts bind tightly with their locking grip and seldom come off. The more likely scenario, especially since so many are used in manufacturing and by power tools, is that these nuts will become lost in the course of maintaining, cleaning, and repairing mowers and other equipment. For this reason, it's always important for the user to purchase more than the anticipated number needed. Make sure also to purchase hex nuts like these that are OEM certified and guaranteed.
This replacement part is a hex screw. This part is small but important in many different kinds of equipment. Hex screws are able to work with other small parts such as washers or nuts to ensure that components are secure within the equipment.Overtightened screws might be stripped and could fall out or get stuck in place, necessitating replacement. Over time, exposure to the elements may lead to a screw becoming worn or corroded, which may cause it to break or get stuck.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.