Search Results

Bought the leveling feet and screwed them in the bottom and they work great. Read more

Bought and installed bumpers Read more

• Shakes and moves

REPLACING THE SUSPENSION PADS AND REPLACE THE BALNCE RING EVEN IF MY DIDN'T LEAK ANY FLUID OUT OF IT... IT SOLVE THE PROBLEM, IT WORKS BETTER NOW THAN IT EVER DID, THE ONLY THING I COULD COME WITH IS THE MANUFACTURE PUT THE WRONG BALANCE RING IN IT TO START WITH... MY IS A 400 KENMORE TOP LOADER, IT IS THE EASIES WASHER I HAVE EVER TAKEN A PART.. I WISH CARS WERE THAT EASY... IT TOOK ME OVER A MONTH FIGHTEN THIS PROBLEM UNTIL I FOUND IT ON YOUTUBE... WHAT BLESSING IT WAS... Read more

I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more

I have a large Samsung 4 door refrigerator. One of the rear wheels broke. To replace it, you need the wheel and the shaft. To lift the refrigerator for the repair, I had my wife stand in front of it with her foot on a board that was wedged against the front wheels. I then pushed the refrigerator up from behind and slid a 3/4" piece of plywood underneath the bottom with my foot. This gives you enough space to do the repair. After removing the back cover, it's best just to knock out the broken... Read more

Ordered a new leg from Appliance Parts & put it on. Read more

• Touchpad does not respond

Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more

Rood Cause #1: One of the front roller bearings was worn out and did not spin freely. Solution #1: I replaced the two front roller bearing assemblies (both included 2-pack). Rood Cause #2: The bottom surface of the compactor slide-out assembly had become deformed (convex) most likely due to the repeated force of compaction over the years. This bottom surface rubbed against the lower frame as evidenced by removal of paint (bare metal was exposed). Friction prevented the compactor drawer... Read more

Purchased 2 replacement feet risers. A very awkward repait. Read more

Replace front legs and rear legs took about 30 minutes. Made sure rear legs had lithium grease applied ran a load of wash very little Vibration nothing compared to before legs were installed and balanced the machine with a level. Read more

Of course, before disassembling anything, I unplugged and turned off the gas supply. To replace the spark electrode, I removed the drip pan/surface to gain access to the burner assemblies. Next, I unscrewed (with a 1/2" open-end wrench, I think) and disconnected the gas supply tubing from the burner assembly with the cracked electrode, and then unscrewed the assembly itself from the base surface. With the assembly detached, I flipped it over and removed the screw that secured the cracked... Read more

Used the video with the parts and replaced the wheels. The only thing we did wrong was using the front wheel axle instead of the back wheel axle on the back wheels. I will just order two more front wheel axles which are longer than the back axle. Thank you for the video, it made this repair easier. Read more

Used the schematic provided to select the parts needing replacement and placed the order. Parts arrived and swapping new for old was simple. For the most part it was a matter of taking out the old and putting in the new. There were a few screws with wheels to replace but that was easy as well. Before purchase I searched several different sites and found all the parts needed. I compared prices of each item as well as shipping cost. Prices for each item were nearly identical between sites... Read more

My brother saw the parts on the counter when they came for dinner. Well that was it, he loves doing that kind of stuff so I said go for it. It was a Kitchen Aid professional mixer, it took him about 30 minutes to complete Works great was a lot easier then I thought it would be. Read more

Drawer was reordered and replaced...fast! Read more

My husband had been searching for replacement parts of over a year. I found your website and asked one of your employees... received a response the following day and ordered the parts! Super simple, and now I have new foot pads that fit my stove burner grates. Thanks so much! Read more