Control Cable

This clutch cable kit is an authentic OEM replacement part for a riding lawn mower or tractor. The clutch cable connects to the idler arm located in the lower deck of a mower and allows the operator to manually engage or disengage the blades. The clutch cable runs up through the steering block and into the front display so that the operator can easily access the clutch. If a clutch cable becomes jammed or tenses up, it will be difficult to depress. If the operator tries to depress the clutch cable without realizing that it is jammed, the clutch cable will snap. The most obvious sign of a snapped clutch cable is that the clutch gives little resistance and the blade cannot be engaged. To change a clutch cable, use a socket set to remove the fuel tank and gain access to the cable. A pair of needle nose pliers is also recommended. This replacement part is compatible with Weed Eater, Husqvarna, Ryobi, and Poulan appliances and comes sourced from its original manufacturer. This part includes a clutch cable and a zip tie.

The drive control cable is a feature of self-propelled walk-behind mowers that engage the gears of the propulsion mechanism. This cable is necessary to allow users to determine when they want to engage the self-propulsion mechanism and when they either want to allow the machine to idle or they wish to push it when mowing in small, tight areas where the self-propelling mechanism is not useful. Occasionally, as with all such mechanisms, the cable may break and it will become necessary to replace the drive control cable. In order to replace the cable, first disconnect the spark plug boot and drain the gasoline, since it's necessary to raise and lower the engine. If it's necessary to place the mower on its side, remember to keep the air filter up so oil does not drain into it. Release the drive cable from the housing that it shares with the engine engagement cable. Remove the drive gear housing on the bottom and the top of the cutting deck. Use needle nose pliers to remove the drive cable. Reverse the process to attach and engage the new drive control cable. This replacement cable is a genuine OEM part, manufactured to be identical to the original cable specifications. This cable is compatible with Craftsman and Husqvarna engines.

The cable seen here is an authentic replacement that is sourced from the manufacturer. This control cable is used for lawn mowers. It will pivot to pull the belt idler pulley, which will fasten the belt and spin the mower's cutting blades. When the cable is not working properly, it could mean that the blades will not spin properly and not provide the mower with the cutting capability that it should have. The cable that comes with the mower tends to be durable, but this does not mean that it will not need to be replaced at some point. Many things could happen to the cable that would require a replacement. The spring might start to wear out, for example. The cable could become frayed or corroded, as well. Owners should always make sure they are wearing gloves when replacing this part. They will need a screwdriver and pliers to complete the repair. The cable is a genuine OEM replacement part that is sold individually. This cable will work with more than 130 models of mowers. Brands with compatible models include Craftsman, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut.

This is a durable rubber clutch cable that is used on lawn and garden tillers. It is used to connect the drive system to the clutch control arm in the equipment. It is an important component that controls the clutch to engage the machine. Over time, the clutch cable can break or become damaged and will need to be replaced. If a visual inspection shows that the clutch cable is broken, the first step is to remove the clutch handle. Take out the bolt on the cover plate for the arm. Take the old cable off of the handle and remove the cover plate. Loosen the screws so the old clutch cable can be removed. Remove the screws on the cover over the clutch and belt. Take off the old cable and attach the new one to the clutch. Tighten the screws and reassemble the parts and make adjustments before using the new cable.This clutch cable is a genuine OEM replacement component sourced directly from the manufacturer. It is sold as an individual part. This cable is compatible with tillers manufactured by MTD, Huskee, MasterCut, and Yard Machines.

This part is a replacement zone control cable. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. This part can be used to replace a defective or broken zone control cable in a variety of lawn mower models. The zone control cable is essential to safe use of the mower as it stops the engine should the user let go of the handle. This part will require replacing if stretched, snapped, or rendered ineffective. When working on or near an enginee, it is important to ensure the equipment is powered down and completely cool before beginning repairs. For more accurate information on how and where to place this zone control cable, the appropriate owner's manual and equipment diagrams should be referred to. As an authentic replacement part, this zone control cable is suitable for use on lawn mowers manufactured by Husqvarna, Poulan, and other brands. Please note that this is a genuine part made of high-quality, durable materials and is sold individually.

This throttle cable is a genuine MTD part, sold individually. This throttle cable can be used as a replacement part for string trimmers. The purpose of a throttle cable for a string trimmer is to allow the speed of the engine to be easily regulated when pulling on and engaging the cable.The throttle cable of a string trimmer might have to be replaced at some point within the standard lifespan of a string trimmer in the event that the component is not functioning as it usually does. This could be the case if the throttle cable is damaged in the form of tearing, ripping, fraying, or erosion to the material. If the speed of the engine is not being regulated by the throttle cable when pulled or engaged, the throttle cable should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This throttle cable is compatible with the following outdoor appliance brands: MTD, Troy-Bilt, Cub Cadet, and Craftsman.

This is a genuine OEM throttle cable that is designed for use with select gas string trimmers. The throttle cable connects to the carburetor and is used to stop the engine from running when the lever is shifted from throttle to choke. Over time, this cable is extended and retracted frequently and can become worn with use. It consists of the metal throttle cable and the plastic housing, and those can get broken or damaged as well, which will require the need for a full replacement. Without a functioning throttle cable, the engine may not run correctly, or the speed of the engine will not be able to be controlled. This replacement cable is ideal for compatible devices. This OEM throttle cable is manufactured to exact standards by MTD. It can be used with a variety of models of trimmers from MTD, Troy-Bilt, Yard Man, Cub Cadet, and Yard Machines. It is made of durable metal with a composite plastic housing. The trigger and screws are sold separately and will require an additional purchase if needed. Be sure to wear gloves when performing any equipment repairs.

This is a reverse cable that is used on many tillers. It's made of durable plastic and metal. The reverse cable is the component in a tool that allows the tiller to help disengage and engage the reverse drive function of the tiller. In some cases, the part will become frayed or broken and must be replaced. The cable also contains delicate connectors that can become damaged. If this occurs, the reverse cable itself will need a replacement. The cable can also become too stretched out and stop working correctly.If the reverse cable for a tiller is broken, stretched out, or otherwise damaged, a pair of pliers will be needed to replace the part. This is a simple repair that only takes a few minutes to handle. The frayed or damaged cable should be removed from the tiller so the new one can be installed in the same place. Before making the replacement, make sure the spark plug wire has been disconnected.This is an authentic OEM replacement component that is directly sourced from the manufacturer. The reverse cable is sold as an individual item. It is designed to be compatible with tillers manufactured by Yard-Man, Craftsman, Huskee, Cub Cadet, MTD, and Yard Machines.

This lift cable is designed for use with many lawnmowers and snowblowers to ensure that the gears run smoothly while using the equipment. The lift cable is made of durable materials but has delicate connectors on each end which may eventually wear out. When the connectors or cables are damaged, the part will need to be replaced. This component is important since it helps control how fast the blades or other parts of the tool can operate. If the cable breaks, the tool may not start.If the lift cable has gone bad, is worn out, or is damaged, replacement is needed. There will be no need to use tools during the process, but work gloves can be helpful. The lift cable can be untwisted from the housing and removed from the tool. Take the new component and place it in the same location. Make sure to reassemble any additional parts before useThis is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The lift cable is made to fit lawnmowers and snowblowers manufactured by Craftsman, Toro, Cub Cadet, Troy-Bilt, MTD, Huskee, Montgomery Wards, and Yard-Man.

This throttle cable is a used on string trimmers. This part links the carburetor assembly to the throttle trigger. Each throttle cable is made with a connector on each end. Over time, the throttle cable can be damaged or kinked through use. If this occurs, the cable will need to be replaced.Replacing the throttle cable will require basic tools and a set of work gloves. The first step to replacing the throttle cable is removing the original component. The throttle housing will need to be taken apart on each side of the string trimmer. The replacement cable will pass through the carburetor mounting plate hole and the engine housing before reassembling the rest of the parts.This throttle cable is sold as an individual component. It is a genuine OEM replacement part that is sourced directly from the manufacturer. The throttle cable is made for use with string trimmers manufactured by Yard Machines, MTD, Craftsman, Murray, Yard-Man, Bolens, and Cub Cadet.