Axle, Roller, Shaft, Wheel

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

The front-drive wheels are attached to the axle with a ring gear and a left-hand smaller gear inside. The wheels are responsible for keeping the mower deck from touching the ground and keeping the blade at a good height for safe operation. They also provide easy maneuvering of the lawnmower. The black and white finish offers a clean, classic look. Although wheels don’t typically wear down enough to need to be replaced, they can become damaged over time. If the wheels are broken or missing, this replacement from the manufacturer can get a lawn mower rolling again in no time at all. Although it’s not required, it is suggested to replace wheels in pairs to ensure even wear over the lifespan of the mower. The front-drive wheel is compatible with several MTD and Troy-Bilt lawnmowers that require front drive wheels. This wheel is typically for self-propelled models. This item is sold as a single unit and additional wheels will have tobe purchased separately. These sturdy plastic wheels are direct from the manufacturer and made to their exact standards to guarantee proper performance and fit with every compatible model.

A lower flexible drive shaft is located inside lawn trimmer attachments. It is mounted inside the lower boom housing. The function of the part is to drive the trimmer head. The drive shaft will deteriorate and become more round with use. The rounded ends will ultimately fail to engage the trimmer head. The lower flexible drive shaft may also break or kink. The trimmer head stops quickly when this occurs. The trimmer will no longer function properly, and a replacement part is required.When replacing the lower flexible drive shaft in a trimmer, wear protective gloves. Start by removing the trimmer head, reel, and line assembly. Use a screwdriver to remove the outer head. Remove the guard assembly. Remove the bushing housing assembly. Access the lower flexible drive shaft and remove the damaged part. Lubricate the new part and install it with the lower flexible drive shaft's ring closest to the trimmer head. Reassemble the trimmer.This replacement part is an OEM genuine part supplied by the manufacturer. The lower flexible drive shaft can be used in MTD, Cub Cadet, Troy-Bilt, and Craftsman brand lawn trimmers. The part is sold individually. The lower flexible drive shaft is made of durable materials.

This is a genuine replacement wheel that is designed for use on select models of lawn mowers from MTD. These wheels feature a cogged design and unique tread pattern to help provide increased lifespan. Still, the durable plastic wheels can become damaged or worn over time. They may also become damaged from impact or the axle can break and cause damage to the wheel. Regardless, a replacement will be necessary to ensure the mower can operate properly. In addition to providing guidance, the wheels keep the blade from coming into contact with the ground, and in select models, the wheels set the cutting height. This is a genuine OEM product manufactured to exact standards by MTD. It can be used in select models from MTD, Craftsman, Troy-Bilt, and Cub Cadet. The durable black plastic wheel measures eight inches in diameter and is sold individually. Be sure to wear gloves and allow the mower to cool before replacing the wheel. Pliers may be needed to remove the pin holding the old wheel in place.

This front roller is used as a replacement part on lawnmowers from major lawn and garden manufacturers. It attaches to the lawn mower's front deck to keep the mower level with the surface of the yard. If the roller is damaged or missing, the lawnmower deck will be unlevel, which can cause various problems. If the front roller is too low, the mower can scalp the lawn leaving bare spots. These spots will turn brown and have to be reseeded to restore the grass. If the front is too high, the grass will be cut unevenly.If the lawnmower is cutting but not cutting evenly or is leaving bald areas, the front roller should be inspected and replaced as needed. Normal wear and tear may have loosened it, or it may be damaged from hitting rocks and sticks in the yard. Replacement is simple and can normally be completed in less than half an hour. Make sure the lawnmower is cool and parked on a level surface. Pliers are needed to remove and replace the roller.This front roller is a genuine OEM part sourced directly from the manufacturer. It is sold as an individual unit. The front roller is made compatible with lawnmowers manufactured by Cub Cadet, Huskee, MTD, and Troy-Bilt.

This part is a replacement wheel assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. If the current wheel assembly is broken or defective, this part can be used as a replacement. It is intended for use with lawn mowers and chipper/shredders.The wheel assembly is a high wear and tear part that may need to be replaced during the natural lifespan of the equipment. Wheels that are bent, dented, broken, or otherwise damaged can prevent the user from properly maneuvering the equipment. When working on or near an engine, always ensure that the equipment is powered off and completely cooled down before attempting to undergo any repairs. For more accurate information on how and where to install this wheel assembly, the appropriate owner's manual and equipment diagrams should be referenced. This wheel assembly is suitable for use on a variety of lawnmower and chipper/shredder models manufactured by MTD, Craftsman, Yard Machines, Cub Cadet, and Husky. It is a genuine OEM part and thus is made of high-quality, durable materials. Part sold individually.

This genuine replacement part is a 9 x 2 inch MTD wheel complete assembly. This part is for use with walk-behind self-propelled lawn mowers. This complete wheel features link tread to provide better grip. This wheel assembly is the rear wheel, and attaches to the bottom of the mower to allow for good grip and smooth rolling, even on uneven ground. Over time, the wheels on a lawn mower can wear out or become damaged. This can reduce traction or affect the alignment of the mower. Replacing the wheel assembly is simple, but be sure to shut off the engine of the mower. Allow the engine to become cool before installing this part. Disconnect the spark plug to prevent the mower from accidentally starting. This OEM replacement part is made of high quality plastic, and is sourced directly from the manufacturer. This part is sold individually. This part is compatible with a variety of Craftsman, Cub Cadet, Yard Machines and MTD lawn mowers.Please note: original part numbers 734-1836, 734-1837, 734-1838, 734-1981, 734-1850 are now obsolete, and manufacturer has replaced the original part numbers with this part.

This wheel is a replacement part that can work for several types of lawn and garden equipment. The rear wheels enable users to maneuver their machines easily. If there is damage to one or more of the wheels, it will be difficult, and in some cases impossible, to use the machine properly and safely.Wheels on lawn and garden machines are constantly exposed to the elements. Despite their durability, they can start to wear down over time. Additionally, there is the chance that the wheel could break if it hits rocks, ice, or other debris. If a wheel is damaged, it should be replaced as soon as possible. The replacement process is simple. It is a good idea to replace both rear wheels at the same time.This wheel is a genuine OEM replacement part and is sold individually. Those who need to replace both wheels will need to buy two. The wheels will work with certain models of snowblower and lawnmowers from Yard Machines, Cub Cadet, MTD, and Craftsman.

This is a complete wheel assembly for walk-behind and push lawnmowers. It is a single replacement wheel for the front wheels on a mower. Wheels may be damaged by impact with hard objects or from exposure to the elements over time. When the wheel is visibly damaged or otherwise does not roll as well as it should, it should be replaced.If the user is having difficulty pushing the walk-behind lawn mower, a visual inspection of the wheels will determine if a new part is required. Replacing a wheel on a lawn mower is simple. Tools including a socket set, pliers, and a screwdriver may be necessary to perform the repair.This wheel is a genuine OEM replacement part. It is compatible with MTD, Troy-Bilt, and Yard-Man machines. It is sold as an individual unit. The wheel is made of durable plastic.