Frigidaire Dishwasher Handle

The Latch is an OEM part for Frigidaire dishwashers. It secures the dishwasher door during operation, ensuring a watertight seal that prevents leaks and allows the dishwasher to run efficiently.

Causes of a bad latch can include wear and tear from regular use, damage from slamming the door, or misalignment over time. Additionally, the latch mechanism can wear out, affecting its ability to hold the door shut.

Symptoms of a bad latch include:

• Dishwasher door not closing or latching properly
• Mid-cycle interruptions due to door opening
• Leaks around the dishwasher door
• The dishwasher not starting because the door is not securely latched

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Color: Black

Note: White / Almond colors are no longer available.

The Dishwasher Door Latch Kit is an OEM part for Frigidaire dishwashers. This kit includes the latch mechanism and necessary components to secure the dishwasher door during operation. The latch ensures that the door stays tightly closed, preventing water leaks and enabling the dishwasher to run its cycles efficiently.

You should replace the door latch kit if it becomes faulty or damaged. Common causes of a bad door latch include regular wear and tear from frequent use, physical damage from forceful closing, or misalignment over time. A compromised door latch can lead to the dishwasher not starting, interruptions during cycles, and potential water leaks.

Symptoms of a bad door latch kit include:

• Dishwasher door not staying closed
• Dishwasher not starting or stopping mid-cycle
• Water leaks from the door area
• Difficulty in latching or unlatching the door

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Frigidaire handle and latch assembly is an OEM replacement part responsible for securing and latching the dishwasher door when it is closed for a wash cycle. This part is typically located on the front panel of the dishwasher, near the top of the door. It ensures that the dishwasher door remains securely closed during operation, preventing water and steam from escaping the interior.

Causes of a bad handle and latch assembly can include repeated use leading to wear and tear, accidental damage from forceful closing or opening, or internal mechanical failures. If the assembly is compromised, the dishwasher may not start, or it could leak during cycles.

Symptoms of a bad handle and latch assembly include:

• Difficulty in opening or closing the dishwasher door
• The door not latching properly
• The dishwasher not starting or pausing mid-cycle
• Water leakage from the door during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Strike is an OEM replacement part for Frigidaire dishwashers. It helps to secure the dishwasher door in the closed position during wash cycles. The door strike works with the door latch mechanism to provide a tight seal to help prevent water, debris, and unwanted odors from escaping the washer interior. 

Symptoms of a bad door strike include:

• The dishwasher door not latching and popping open during cycles
• Leaks or water escaping around the door seal  
• The door not feeling secure when closed
• Increased noise levels from a poor door seal

Over time, the door strike can become worn, bent, or damaged from normal use. Ensure your dishwasher door seals tightly with this genuine OEM Frigidaire replacement part.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement latch secures the door closed so the appliance can operate correctly. Restores a positive close and consistent door recognition to help prevent no-starts and intermittent operation. What it does / common symptoms:

• Engages the strike to hold the door/panel closed
• Ensures the door-closed signal is made so controls can run
• Worn or broken latch may cause the door not to stay shut
• Unit may not start, show a "door" message, or stop if the door is bumped

• 1 latch

• Disconnect power before servicing; turn off water supply if applicable
• Access the latch per model—typically behind the front panel or inner door liner
• Note and transfer any springs/clips from the original latch to the new one
• Verify smooth open/close and proper strike engagement before testing operation

This strike is the receiver the door latch engages with to keep the door securely closed. A properly aligned strike helps the appliance recognize a closed door so cycles can start and run without interruption. What it does

• Provides the catch point for the door latch to secure the door during operation
• Helps align the latch for smooth, consistent engagement
• Ensures the door-closed switch can be activated so the unit can start
• Worn, bent, or broken strikes can cause the door not to latch, pop open, or trigger door-open errors

• 1 strike

• Disconnect power before servicing; follow manufacturer safety procedures
• Note the strike's orientation and any shims/spacers before removal
• Reuse existing mounting hardware unless your model specifies otherwise
• After installation, check alignment and the latch engages smoothly without force

Restore a secure, reliable door closure. This replacement door latch engages the door mechanism so the appliance recognizes the door is closed and can operate as intended, preventing nuisance "won't start" issues caused by a broken latch. What it does:

• Keeps the door closed and properly aligned with the catch
• Engages the door mechanism/switches so the unit can run when shut
• Replaces worn or broken latch hook tabs
• Common symptoms: door won't close or stay latched; unit won't start; must push/hold door to run; visible broken latch hook

• 1 door latch

• Disconnect power before servicing; wear cut-resistant gloves
• Access the door's inner panel/trim to reach the latch; protect glass and finishes
• Note spring/clip orientation if present and transfer any reusable hardware
• Test door latching and proper operation before final reassembly

Replacement refrigerator door handle that restores a secure grip and reliable opening for compatible Frigidaire units. Replaces worn, cracked, or missing handles to improve usability and the appliance's appearance. What it does:

• Provides a stable grip for opening and closing the refrigerator door.
• Replaces handles that are cracked, broken, loose, or missing.
• Restores original mounting points and clearance so the door operates smoothly.
• Improves the look of the appliance by replacing damaged or discolored hardware.

• Disconnect power to the appliance before starting any repair.
• Removal may require lifting end caps or trim and removing mounting screws—use the correct tools.
• Keep original screws and trim; confirm orientation before removing the old handle.
• Your model's service manual or OEM instructions for exact disassembly and torque details.

This towel bar assembly replaces a worn, cracked, or loose oven door handle to restore a secure grip and clean appearance. Designed to mount to the oven door so you can open and close the door safely and easily. What it does:

• Provides a sturdy handle for opening and closing the oven door
• Replaces broken, bent, or loose towel bars or mounting tabs
• Restores proper alignment and grip for safe operation
• Helps maintain the oven door's finished appearance

• Disconnect power to the appliance before beginning any repair
• Handle hardware may require removal of the oven door or access panel; keep fasteners for reassembly
• Use appropriate hand tools and avoid overtightening to prevent stripping threads or cracking mounting tabs