Frigidaire Dishwasher Valve

The Water Inlet Valve is an OEM replacement part for Frigidaire washing machines. It is a component responsible for controlling the flow of water into the washing machine tub during the wash and rinse cycles.

Symptoms of a faulty Water Inlet Valve include:

• No water or insufficient water entering the washing machine tub
• Washing machine not filling or taking an excessive amount of time to fill
• Leaks or water dripping from the inlet valve area
• Unusual noises or vibrations during the fill cycle

Causes of a bad water inlet valve can include normal wear and tear over time, sediment buildup or blockages, electrical malfunctions, or physical damage from water pressure issues or freezing conditions.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore washing machine models.

The Inlet Valve is an OEM part for Frigidaire dishwashers. This valve is essential for controlling the flow of water into the dishwasher, ensuring the appliance receives the correct amount of water during the wash and rinse cycles. The inlet valve operates by opening and closing in response to electrical signals from the dishwasher's control board, allowing water to fill the dishwasher tub at the appropriate times.

Symptoms of a failing Inlet Valve include:

• The dishwasher not filling with water at the start of a cycle
• Water entering the dishwasher slowly or inconsistently
• The dishwasher overfilling or leaking
• Unusual noises such as buzzing or humming during the filling stage
• Water remaining in the tub after the cycle is complete

Causes of a bad inlet valve can include mineral buildup from hard water, which can clog the valve, wear and tear on the valve components over time, or electrical issues that prevent the solenoid from functioning correctly.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This flapper valve is the dishwasher's one-way drain check. It directs wastewater out and helps prevent backflow into the tub, promoting complete draining and reducing standing water, odors, and water returning after the drain cycle.

• Maintains one-way water flow from the sump/pump to the drain hose
• Helps prevent backflow from the sink or air gap into the dishwasher tub
• Wear, warping, or sticking can lead to slow draining or water left in the tub
• May also present as water backing into the tub after a cycle or intermittent drain faults

• Disconnect power and turn off water supply before servicing
• Access the valve at the drain outlet/pump area; note hose and clamp orientation
• Match the original valve orientation; the flapper should open toward the drain hose (direction of flow)
• After reassembly, run a short fill-and-drain test and inspect for leaks and proper draining

The Water Inlet Valve is an OEM part for Frigidaire dishwashers. It plays a crucial role in the hydraulic system by controlling the flow of water into the dishwasher. The valve is designed to precisely regulate water pressure and supply the appropriate amounts of water at specific times during each washing cycle.

Causes of a bad valve include wear and tear over time, mineral buildup that obstructs flow, or damage from freezing or overheating. 

Symptoms of a bad valve include:

• Improper or inconsistent water levels during the cycle
• Leaks or flooding in the base of the dishwasher 
• Inability to select or begin washing cycles
• Illumination of error codes relating to water problems

This OEM Frigidaire replacement part is also compatible with Gibson, Kelvinator, and Kenmore models. 

The Water Valve is an OEM part for Frigidaire dishwashers. This valve controls the flow of water into the dishwasher, ensuring the correct amount of water enters the tub during the wash cycle.

Causes of a bad water valve can include mineral buildup from hard water, electrical failures, or wear and tear from regular use that affects the valve's ability to open and close properly.

Symptoms of a bad water valve include:

• The dishwasher not filling with water
• Leaking water around the valve area
• Inconsistent or insufficient water levels during cycles
• Unusual noises when the valve is in operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Water Valve is an OEM part for Frigidaire dishwashers. It is responsible for controlling the flow of water into the dishwasher, ensuring the correct amount of water is used during each cycle.

Causes of a bad valve can include mineral buildup, wear and tear over time, or damage from high water pressure or freezing temperatures.  

Symptoms of a bad valve include:

• Dishwasher not filling with water
• Water leaking from the valve area
• Irregular water levels during cycles
• Delayed or incomplete wash cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This float detects and monitors water levels in the appliance's sump/drain area to help prevent overfilling and water pooling. Replacing a damaged or stuck float restores proper water sensing and reduces leak risk. What it does:

• Senses water level in the drain pan or sump so the appliance can stop or redirect water flow
• Helps prevent water from overflowing or pooling under the appliance
• Can stop false fill/overfill conditions caused by a stuck or broken float
• Fault symptoms include water pooling, continuous or unexplained filling, or failure to drain properly

• Always unplug the appliance before accessing internal panels or service areas
• Remove the required access panels or trim to reach the sump/drain area; follow the model's service manual
• Handle the float and any clips or wiring carefully to avoid damage; reconnect any electrical connectors securely
• After installation, restore power and run a manual fill/drain test to verify proper operation

This replacement pump moves water/condensate through your appliance so it can drain or recirculate as designed. Replacing a weak or failed pump restores proper water removal and helps prevent leaks, overflows, or nuisance shutoffs.

• Moves collected water from the sump/collection area to a drain hose or internal passage
• Maintains correct water level to prevent overflow conditions
• Common failure signs: water won't pump out, leaks near the base, or loud buzzing/grinding from the pump
• May trigger "bucket full," drain, or pump-related error indicators, depending on the model

• Disconnect power before servicing; allow unit to cool, and expect residual water in the lines or pan
• Note hose routing and wiring connections; transfer any clamps, grommets, or fittings from the old pump if reused
• Ensure hoses are fully seated and not kinked; tighten connections and check for leaks after reassembly
• Test operation after installation and water is expelled properly

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser so your appliance makes ice and dispenses water reliably. Replaces a failed valve to restore normal water delivery and prevent leaks. What it does:

• Opens and closes to route household water to the ice maker and dispenser when signaled.
• Stops water flow when the fill cycle ends to prevent overfilling.
• Commonly replaces valves causing no water to the dispenser or ice maker.
• Also used when valve leaks or runs continuously.

• Turn off the refrigerator and shut off the water supply before starting work.
• Disconnect electrical connectors and water lines carefully; expect minor residual water.
• Inspect hose fittings and seals; test for leaks after installation.

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This water inlet valve controls water flow to the refrigerator's ice maker and dispenser, restoring proper water delivery when the system won't fill or dispense. Direct-fit replacement that helps stop leaks and restore function. What it does:

• Opens and closes to let water into the ice maker and dispenser when signaled
• Stops water flow when the fill cycle or dispense cycle ends
• Common part to replace for slow/no ice production or no water from dispenser
• Replaced when valves leak or water lines fail to pressurize

• Disconnect power and shut off the water supply before starting work
• Verify tubing connections and electrical connector orientation before reassembly
• Inspect supply lines and gaskets; use proper replacement fittings if damaged

This water inlet valve controls water flow into the refrigerator for the dispenser and ice maker, restoring reliable filling and ice production. It replaces a worn or failed valve to stop flow issues and intermittent filling problems. What it does:

• Controls and directs incoming water to the ice maker and door dispenser via two solenoids
• Opens and closes to allow timed fills for ice production and dispensing
• Commonly used when the dispenser produces no water or has weak flow
• Can cause the ice maker to stop filling or produce small/partial ice cubes

• Disconnect power and shut off the water supply before servicing
• Inspect and tighten water line fittings; check for leaks after reconnecting water