Frigidaire Dishwasher Bracket & Flange

This dishwasher rack tine row bracket secures the fold-down tine row to the rack so it pivots and locks correctly. Replacing a cracked or missing bracket helps restore stable plate support and smooth loading.

• Secures the fold-down tine row to the dishrack
• Allows the tine row to pivot between upright and flat positions
• Helps keep dishes from tipping during cycles
• Common symptoms: tines won't stay up, row flops loosely, bracket is cracked/missing

• Disconnect power to the dishwasher before servicing
• Pull out the rack and locate the affected fold-down tine row
• Release the old bracket and snap the new bracket onto the rack wires
• Verify the tine row pivots and latches smoothly before returning the rack

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

This replacement bracket is used in Frigidaire-made dishwashers to secure an associated component or panel. Replacing a broken or missing bracket restores a tight fit, alignment, and stability so parts don't loosen, rattle, or shift during cycles. What it does:

• Provides a rigid mounting point for the connected part or panel
• Maintains proper alignment and stability during operation
• Helps reduce rattling or vibration from a loose component
• Replaces a broken, bent, rusted, or missing bracket

• 1 bracket

• Disconnect power and turn off the water supply before servicing
• Access and mounting location vary by model; refer to your service or installation manual
• Wear cut-resistant gloves; bracket edges may be sharp
• Save and reuse the original screws/fasteners; install in the same orientation and tighten securely

The Mounting Bracket is an OEM part for Frigidaire dishwashers. It is a metal component that secures the dishwasher to the surrounding cabinetry. The mounting bracket provides structural support and stability during operation.

Causes of a bad mounting bracket can include damage from installation/removal, cracks or deformities from heavy loads, or broken welds/fasteners holding it in place.

Symptoms of issues with the mounting bracket include:  

• Excessive vibration or shaking of the dishwasher during cycles
• The unit not sitting level or secured properly in the space
• Noises related to movement that shouldn't occur
• Visible damage or instability of the unit 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This replacement brace is a support bracket that helps secure and stabilize appliance panels and components, restoring proper alignment and reducing vibration. Designed for direct fit where the original bracket is damaged or missing. What it does:

• Provides structural support to panels, frames, or assemblies to maintain alignment and fit
• Secures components to prevent wobbling, rattling, or movement during operation
• Helps restore proper door or panel fit when a broken or bent bracket causes misalignment
• Reduces noise caused by loose or unsupported parts

• One replacement brace

• Disconnect power or unplug the appliance before starting any work
• Use the original screw locations and hardware where possible; save any reusable fasteners
• Inspect surrounding panels and mounting points for additional damage before reassembly

This metal bracket secures the appliance's front frame/trim to the cabinet, keeping the front panel aligned and stable for a clean appearance and quiet operation. Replaces a worn or damaged front frame support. What it does:

• Fastens the front frame or trim to the cabinet to maintain panel alignment
• Prevents excessive movement, vibration, and rattling of the front panel
• Helps keep gaps even for proper door/trim fit and appearance
• Supports proper seating of adjacent panels and controls

• Disconnect power to the appliance before beginning any work
• Remove the front trim or access panel to reach the bracket fasteners
• Use common hand tools to remove and replace the bracket; retain original fasteners unless damaged
• Inspect surrounding trim and mounting points for damage and replace as needed; test panel alignment after installation

This shelf bracket secures a refrigerator shelf to the liner so shelves stay level and stable during normal use. It replaces a cracked, broken, or loose bracket to restore proper shelf support and alignment. What it does

• Supports and locks a refrigerator shelf into position to prevent tipping or slipping
• Restores shelf stability when an existing bracket is cracked, worn, or broken
• Helps keep stored items from shifting by maintaining a level shelf
• Works with the shelf system shown in the OEM parts list for this bracket

• One shelf bracket

• Remove food and shelves before beginning to avoid spills and damage
• Typically installs with simple snap-in or screw fasteners; match existing fastener type
• Wear gloves to protect hands from sharp edges inside the cabinet