Frigidaire Dishwasher Clip Or Clamp

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This hose clamp secures flexible water or drain hoses to fittings to prevent leaks and keep connections tight. It's a simple replacement that restores a secure seal and helps stop drips or loose hoses. What it does:

• Holds a rubber or plastic hose firmly to a barb or nipple to prevent leaks
• Restores a tight connection when original clamp is corroded, bent, or broken
• Helps eliminate water dripping, puddling, or intermittent leaks at hose joints
• Prevents hoses from slipping off during vibration or normal appliance use

• Disconnect power and shut off water supply before starting any repair
• Tighten clamp securely with pliers or the appropriate tool; avoid over-tightening which can damage the hose
• After installation, restore water and power, then check the connection for leaks

This spring-style clamp secures flexible hoses and tubing on appliance water and drain connections to help stop leaks and maintain a tight seal. A simple replacement when original clamps corrode or lose tension. What it does:

• Holds hose or tubing firmly on barbed fittings to prevent leaks and disconnections
• Restores reliable sealing on water inlet, drain, or vent hose connections
• Commonly used where a compact, tensioned clamp is required
• Helps stop symptoms like dripping, puddling, or loose hose connections

• One spring-style clamp

• Turn off power and water supply to the appliance before servicing
• Use pliers to expand the clamp for removal and installation; avoid sharp tools that can damage the hose
• Replace any hoses or fittings that show damage or excessive wear

This sump retainer secures the appliance sump assembly and helps keep the pump seal and surrounding components properly positioned to reduce leaks and maintain correct water flow. It's a small replacement part used during sump or pump repairs. What it does:

• Holds the sump housing or pump assembly in place to maintain a reliable seal
• Helps prevent water leaks from the pump/sump area when installed correctly
• Keeps internal components aligned for proper water circulation and drainage
• Commonly replaced when sump hardware is cracked, warped, or no longer secures the pump

• One sump retainer

• Power off and unplug the appliance before starting any repair
• Verify you have full access to the sump/pump area; removal of panels or racks may be required
• Inspect surrounding seals and gaskets; replace if damaged to ensure a watertight fit

Red

This replacement part is a fastener, and it is intended for use in different types of appliances. This is a genuine replacement part made by Frigidaire. Fasteners are a small metal part that is used in many spots in refrigerators or freezers. These clips are able to help keep shelving and other items in place so that the appliance works properly. A new fastener might be needed if there are any parts of the fridge or freezer that are loose or falling off. The fasteners allow the shelving and other attachments to stay steady, so if anything is not attached properly, it might be time to replace the fasteners. It is possible that the fasteners might become brittle over time as they are typically held in cool or freezing conditions. Many appliances require more than one fastener so be sure that the correct amount is ordered. This fastener is sold individually and is compatible with appliances made by Frigidaire. Also note that this part is a genuine OEM replacement part.