Frigidaire Dryer Gasket & Seal

The Lower Felt Seal is an OEM part for Frigidaire dryers. This part creates a tight seal between the drum and the front panel, preventing air leakage and reducing energy consumption.

Symptoms of a failing Lower Felt Seal include:

• Clothes getting snagged or caught during the drying cycle
• Increased drying times due to heat escaping from the drum
• Excessive noise or squeaking as the drum rotates
• Visible wear, tears, or gaps in the felt seal

Causes of a bad lower felt seal can include regular wear and tear from the constant rotation of the drum, physical damage from overloading the dryer, or deterioration due to exposure to heat and humidity over time.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Drum Glide is an OEM part for Frigidaire dryers. It is designed to support the front of the dryer drum as it rotates, allowing the drum to turn smoothly with minimal friction and noise. This is a single glide. Your dryer uses two so it is recommended to replace both at the same time.

Causes of a bad drum glide can include wear and tear from regular use, excessive loads that put undue strain on the drum and its components, or accumulation of lint and debris that can interfere with the glide's movement.

Symptoms of a bad Drum Glide can include:

• Unusual noises, such as screeching or squealing, during operation
• Increased difficulty in turning the drum, leading to longer drying times or incomplete cycles
• Visible wear or damage to the glide itself, indicating it is time for a replacement

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Upper Felt Seal is an OEM part for Frigidaire dryers. It provides a seal between the dryer drum and the front panel, helping to retain heat and ensure efficient drying performance. This felt seal also minimizes friction between the drum and the front panel, reducing wear on the drum and the appliance itself. The seal measures approximately 16.5" long x 1" wide. The adhesive is included as well.

Causes of a bad upper felt seal can include wear and tear over time, exposure to high heat, or damage from foreign objects caught in the drum. A compromised felt seal can lead to inefficient drying and increased energy consumption.

Symptoms of a bad upper felt seal include:

• Clothes taking longer to dry
• Excessive lint accumulation inside the dryer
• Unusual noises during the drying cycle
• Visible damage or gaps in the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Also available in maintenance kit: Part Number 5304457724.

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

The Upper Felt Seal is an OEM part for Frigidaire dryers. This felt seal is located at the top edge of the dryer drum and is designed to create a tight seal between the drum and the dryer cabinet. This helps prevent clothes from getting caught in the gap and ensures efficient drying by maintaining proper airflow within the drum. For High Temp adhesive order part number: [AP2153130].

Causes of a bad upper felt seal can include regular wear and tear from frequent use, friction and heat exposure over time, and damage from foreign objects inadvertently caught in the dryer. A compromised seal can lead to inefficient drying, increased wear on clothes, and potential damage to the drum.

Symptoms of a bad upper felt seal include:

• Clothes getting snagged or torn during drying
• Unusual noises such as squeaking or rubbing from the drum area
• Decreased drying efficiency or longer drying times
• Visible wear, thinning, or detachment of the felt seal

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement gasket restores a tight, reliable seal between mating parts in your appliance. It helps contain water or air at the joint to prevent leaks, odors, and performance issues.

• Creates a compressible barrier that prevents leaks at the sealed interface
• Helps maintain proper containment/airflow, depending on application
• Replace if torn, cracked, shrunken, or permanently flattened
• Typical symptoms include moisture or drips at the seam, musty odors, or visible damage

• Disconnect power; shut off water supply if applicable before servicing
• Use your model's parts diagram to locate and orient
• Clean and dry mating surfaces; remove any old adhesive or residue so the new seal seats properly
• Reassemble evenly, avoid over-tightening fasteners, and test for leaks after reassembly

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

This gasket forms a tight seal between mating components in your appliance, helping contain water, air, or heat as designed. Replacing a worn gasket restores proper sealing and helps prevent leaks, performance loss, and residue buildup. What it does:

• Creates a compressible seal between two parts to prevent leakage and maintain proper airflow or water containment
• Helps reduce rattles and wear at the joint by cushioning the connection
• Supports efficiency and consistent performance by keeping the system properly sealed
• Common symptoms of failure: visible cracks/tears or flattening, leakage at the joint, heat or moisture escaping, or persistent odors near the seal

• 1 gasket

• Disconnect power; shut off water supply before servicing
• Note the gasket's orientation and take reference photos during disassembly
• Remove the old gasket and thoroughly clean mating surfaces of residue or debris
• Seat the new gasket evenly without stretching; reassemble and test for a proper seal

This glider is a replacement drawer support that helps guide and stabilize a sliding refrigerator or freezer drawer for smooth opening and closing. It restores proper alignment and prevents the drawer from sticking or falling out of its track. What it does:

• Guides the drawer along its track to ensure smooth, even movement
• Maintains drawer alignment to prevent binding or tipping
• Replaces worn or broken gliders that cause noisy or jerky operation
• Helps the drawer seat properly so it opens and closes without snagging

• One glider (single drawer support)

• Inspect the track and mating hardware for damage or debris before installing
• Typically snaps or slides into place—no special tools required for most installations
• Replace matching left/right pieces as needed for balanced operation
• For appliance safety, work with the drawer empty and follow OEM service precautions

This glider replaces a worn or broken drawer slide to restore smooth movement and proper alignment for refrigerator drawers. It helps the drawer open and close evenly so stored items stay secure and accessible. What it does

• Supports and guides the drawer as it slides in and out of the cabinet
• Replaces a cracked, worn, or missing glider that causes sticking or uneven travel
• Helps prevent drawer wobble and keeps the drawer aligned on its track
• Compatible with common refrigerator drawer assemblies that use a small plastic/nylon glider

• Basic hand tools may be needed; remove the drawer to access the glider mounting area
• Align the glider with the track and snap or fasten into place per the original hardware
• Inspect adjacent slides and tracks for wear and replace if damaged to ensure smooth operation
• Disconnect power and remove food from drawers before disassembly if working near electrical components

The Front Felt Glide Assembly is an OEM part for Frigidaire dryers. This part allows smooth operation of the dryer drum, providing a felt pad that the drum glides on as it rotates. This not only helps to support the drum but also minimizes friction and noise, contributing to the efficient and quiet operation of the dryer. 

Over time, the felt portion of the glide assembly can wear down, leading to increased friction between the drum and the dryer's front panel.  

Symptoms of a bad Front Felt Glide Assembly include:

• Unusual noises during operation, such as squeaking or grinding
• The dryer drum may catch or hesitate during rotation
• Increased wear and tear on clothing due to the drum's rough movement
• The dryer may take longer to dry clothes efficiently due to the drum's impaired rotation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.