Frigidaire Microwave Parts

This door latch hook secures the refrigerator door latch so the door closes and seals correctly. Replacing a broken or worn hook restores reliable door latching and helps prevent temperature loss from an improperly closed door. What it does:

• Secures the door latch assembly so the refrigerator door stays closed.
• Restores proper latch engagement to help maintain the door seal and consistent cooling when the door was not closing fully.
• Can address symptoms such as a door that won't latch, door popping open, or visible damage to the hook.
• Direct replacement for the factory latch hook to restore proper fit and function.

• Disconnect power to the appliance before starting any repair.
• Remove door trim or inner liner as needed to access the latch; keep all screws and fasteners for reassembly.
• Verify latch alignment and striker position before tightening; hand-tighten first and avoid over-tightening.

High-voltage magnetron that generates microwave energy to heat food in the oven cavity. Replacing a failed magnetron restores heating when the microwave runs but food doesn't warm. What it does:

• Converts high-voltage power into microwave energy to heat food in the oven cavity.
• Commonly needed when the microwave motor and lights run but the unit fails to heat.
• A failing magnetron can cause unusual noises, intermittent heating, or a burning odor.
• Critical high-voltage component — faults can create arcing or other dangerous conditions.

• Disconnect power and unplug the appliance before accessing the microwave cavity.
• High-voltage capacitor may retain a lethal charge—do not attempt capacitor discharge unless qualified.
• Handle the magnetron by the housing, avoid touching ceramic antenna or terminals.

Replace a failed light socket with this lamp assembly to restore reliable illumination inside your appliance. If your bulb is good but the light won't work or flickers, the socket assembly is a likely culprit.

• Holds the bulb and supplies power to illuminate the interior or work area
• Replaces cracked, heat-damaged, or loose sockets and terminals
• Helps resolve no light, intermittent flicker, or arcing at the socket
• Designed to fit the original mounting and wiring on compatible models

• Disconnect power before servicing to avoid electrical shock
• Allow the lamp and surrounding area to cool before handling
• Move wires to the new assembly one at a time to maintain correct connections
• Use the bulb type and wattage specified for your model; do not overtighten the bulb

The Coupler is an OEM part for Frigidaire microwaves. It is responsible for providing a secure connection between the motor and the glass tray.  It enables the smooth rotation of the glass tray turntable, ensuring even heat distribution during the cooking process.

A bad coupler can occur due to wear and tear over time, accidental damage, or improper handling. Signs of a faulty coupler include the glass tray not rotating or turning unevenly during operation.

Symptoms of a bad coupler include:

• The glass tray not rotating 
• Uneven heating  
• Unusual noises  

Replace your faulty microwave glass tray turntable coupler with this genuine OEM Frigidaire part to restore your microwave. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

The Shelf Support is an OEM part for Frigidaire countertop microwaves. It holds and stabilizes shelving inside the microwave cavity during operation. 

Symptoms of a faulty shelf support include:

• Loose or detached shelves that cannot maintain placement  
• Difficulty positioning shelves at desired height levels
• Scrapes or dents on interior microwave walls from shelf movement
• Gaps or spaces where shelf legs do not sit securely  

Causes relate to typical wear of spring clips or brackets holding shelves in place. Regular vibration from microwave turntables can weaken pressure points over time.

This OEM replacement shelf is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Shelf Support is an OEM part for Frigidaire countertop microwaves. It holds and stabilizes shelving inside the microwave cavity during operation. 

Symptoms of a faulty shelf support include:

• Loose or detached shelves that cannot maintain placement  
• Difficulty positioning shelves at desired height levels
• Scrapes or dents on interior microwave walls from shelf movement
• Gaps or spaces where shelf legs do not sit securely  

Causes relate to typical wear of spring clips or brackets holding shelves in place. Regular vibration from microwave turntables can weaken pressure points over time.

This OEM replacement shelf is compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement cover is a protective panel used in the microwave assembly. It shields internal components from grease and debris and restores a clean, secure barrier when the original cover is cracked, burned, or missing.

• Shields internal components from food splatter, steam, and grease
• Helps maintain proper airflow and safe operation inside the cavity
• Common signs it's needed: cover is warped, cracked, scorched, loose, or missing
• Reduces arcing/sparking or buzzing caused by a damaged or contaminated cover

• Disconnect power before servicing; allow hot surfaces to cool
• Remove screws or release tabs to take off the damaged cover; reuse existing hardware if applicable
• Clean surrounding area to remove grease or debris, then seat the new cover fully and secure without overtightening
• For microwaves, internal high voltage can remain even when unplugged.

Compressor start capacitor that helps the refrigerator compressor start reliably so the appliance can maintain proper cooling. Replace a weak or failed capacitor to reduce hard-starting, excessive humming, or loss of cooling. What it does:

• Provides the starting boost the compressor needs to reach running speed.
• Commonly linked to symptoms like compressor humming but not starting, warm refrigerator, or frequent on/off cycling.
• Works with the compressor start circuit; a failed capacitor can prevent the compressor from starting.
• Visible damage, leakage, or failed electrical tests indicate replacement is needed.

• Disconnect power to the appliance before accessing the capacitor.
• Discharge the capacitor before touching terminals to avoid shock.
• Note wire locations or photograph connections before removal; reconnect wires exactly.

This mounting bracket secures internal panels or assemblies to the appliance, restoring proper alignment and reducing movement. A direct-replacement bracket helps stop rattling, keeps parts in place, and supports reliable operation. What it does

• Secures panels, trim, or internal components to the cabinet to maintain proper fit and alignment.
• Prevents vibration and rattling that can occur when brackets are bent, cracked, or missing.
• Restores stable mounting for doors, panels, or assemblies so parts operate smoothly.
• Common symptom: loose or misaligned panels, persistent noise, or visible bracket damage.

• Disconnect power (unplug or shut off circuit) before starting any repair.
• Remove outer panels or trim as needed to access the bracket; keep track of fasteners.
• Inspect surrounding parts and reuse original screws if undamaged; replace hardware if stripped or corroded.

This complete door assembly replaces a damaged or worn refrigerator door to restore proper closure and appearance. It provides a factory-style front panel so your appliance seals and functions correctly without drafts. What it does:

• Replaces the full outer door structure so the door closes flush and helps maintain internal temperature.
• Restores mounting points and handle attachment if the original door is dented, cracked, or warped.
• Helps stop cold air leaks and reduces frost buildup caused by a misaligned or damaged door.
• Returns the appliance to a finished, factory-look exterior when the existing door is cosmetically damaged.

• Disconnect power to the appliance and empty door shelves before starting.
• Have a second person available; door assemblies can be heavy and awkward to handle.
• Keep fasteners and hinges aligned during installation; follow the manufacturer's torque recommendations.

This Frame is an OEM part for Frigidaire microwaves. Designed to provide structural integrity and aesthetic appeal, this frame is a crucial component for the proper alignment and protection of the microwave's door and interface. 

The degradation of a microwave frame can occur due to physical impacts, frequent usage, material fatigue, or environmental factors. A compromised frame can affect the door alignment, sealing, and overall look of the microwave.

Symptoms of a bad frame include:

• Difficulty in opening or closing the microwave door.
• A visible gap or misalignment of the door.
• Cracks or breakages on the frame itself.
• Unusual noises when the door is in operation.
• The door not sealing properly, leading to heat loss or inefficient cooking.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This complete door assembly replaces a damaged or bent oven/microwave door so the appliance closes securely and looks like new. Restores proper sealing, safety, and operation for reliable cooking and protection. What it does:

• Replaces the appliance door to restore proper closing and heat containment
• Re-establishes a secure seal to help maintain internal temperature
• Improves safety by replacing cracked, dented, or warped door components
• Restores finished appearance for a clean, like-new look

• Disconnect power to the appliance before beginning any repair
• Handle glass and trim carefully; support the door during removal and installation
• Retain and re-use any hinge screws or brackets unless replacements are specified

This temperature control thermostat regulates refrigerator temperature to keep food safely chilled. It replaces a faulty control to restore proper cycling and temperature stability for the fresh food compartment. What it does:

• Senses cabinet temperature and opens/closes the compressor/coolant circuit to maintain set temperature
• Can stop excessive cooling or prevent the compressor from running continuously when failing
• Commonly used when the refrigerator is too warm, too cold, or runs nonstop
• Works with mechanical temperature dials and capillary-sensor assemblies on compatible units

• Disconnect power to the appliance before servicing to avoid shock
• Handle any attached capillary sensor tube gently; avoid kinks or sharp bends
• Verify correct mounting and electrical connections; match terminals to the old thermostat

The Magnetron is an OEM part for Frigidaire microwave ovens. Located behind the waveguide plate inside the microwave chamber, the magnetron generates electromagnetic waves to cook and heat food. Powered by a high-voltage transformer, a magnetron coil focuses 2.45GHz radio waves through the waveguide into the cavity.

Causes of a bad magnetron can include failures of the cathode filament or insulator over extended use, depletion of filament or high voltage components.

Symptoms of a bad Magnetron include:

• Slow or incomplete cooking even on high power 
• Discolored or burnt spots on food
• No visible arcing yet cavity runs continuously
• Oversparking sounds or burning smells from chamber

This genuine OEM Frigidaire magnetron is compatible with Electrolux, Gibson and some Kenmore microwave models as well.