Frigidaire Microwave Parts

This door latch spring restores the return tension in your microwave's door release mechanism so the latch engages and releases correctly. Replacing a fatigued or broken spring helps ensure safe door operation and reliable interlock switch activation.

• Provides the return force for the latch lever/door release button
• Helps door hooks engage fully and release smoothly
• Supports proper interlock switch actuation so the unit will run only when the door is closed
• Typical failure signs: door won't latch, "open/close door" error, door button sticks, or needing to hold the door shut to start

• Disconnect power. Microwaves can retain dangerous high voltage even when unplugged; discharge the capacitor
• Access the latch assembly behind the control panel; note the spring's orientation and attachment points
• Use needle-nose pliers to install without overstretching; inspect the latch lever and door hooks for wear
• Verify proper door closure and interlock switch operation before reassembly

This replacement motor restores reliable rotation to the component it drives—bringing back proper airflow or mechanical movement so your appliance runs as designed and noise is minimized.

• Converts electrical energy into steady shaft rotation to power the attached fan, blower, or mechanism
• Common failure signs: won't start, only hums, stalls, or intermittently runs
• Worn bearings or windings can lead to overheating and reduced performance

• Disconnect power before servicing; if the unit uses capacitors, discharge them per the service manual
• Note wire locations and transfer any brackets, grommets, or fan blades from the old motor
• Mount securely, align the shaft, and confirm correct rotation before finalizing
• Spin the shaft by hand to check for free movement, then test for smooth, quiet operation

This replacement lamp restores illumination in your appliance's lighted area. Installing a new lamp brings back clear visibility so you can easily see contents and settings during use.

• Provides light when the door opens or the light switch is turned on
• Replaces a bulb that is burned out, dim, or flickering
• Common symptoms: light not working, intermittent operation, or a blackened/broken filament
• Restores interior/work-area visibility for safer, easier use

• Disconnect power to the appliance before servicing
• Allow the lamp and surrounding area to cool completely before handling
• Handle glass with a clean cloth or gloves; avoid touching the glass directly
• Replace only with the same type and rating specified by the manufacturer

This Turntable Motor is an OEM part for Frigidaire microwaves. Responsible for the rotation of the microwave's turntable, which ensures even cooking and heating of food. This motor ensures that the turntable operates smoothly and reliably, maintaining the efficiency of your microwave.

A malfunctioning motor can lead to uneven heating or cooking of food, as the turntable is integral to the microwave's ability to distribute heat uniformly.

Symptoms of a faulty turntable motor include:

• The turntable does not rotate when the microwave is in use.
• Intermittent or erratic movement of the turntable.
• Unusual noises coming from the turntable area during operation.
• Food is unevenly cooked or heated, indicating inconsistent turntable motion.
• The microwave operates normally except for the turntable function.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

Keep your microwave's ventilation performing its best. This replacement air filter helps screen cooking vapors before the air is recirculated or exhausted, restoring proper airflow and helping maintain cleaner, more effective ventilation.

• Filters air drawn through the microwave's ventilation system during cooking
• Helps reduce cooking odors and airborne particles in the exhaust stream
• Supports proper airflow and fan performance for effective venting
• Replace when saturated, damaged, or visibly dirty; do not operate without required filters
• Common signs of a spent filter: persistent odors, weaker ventilation, or a discolored/brittle filter

• Disconnect power by unplugging the unit or switching off the circuit breaker before service
• Access the filter from the underside panel or top/front grille, per your model
• Note the old filter's orientation; install the new filter the same way and secure any tabs or screws
• Ensure all panels/grilles are reinstalled securely before restoring power

This replacement door handle restores a secure, comfortable grip for opening and closing your microwave door. Replace a cracked, loose, or missing handle to keep everyday use safe and your appliance looking clean and complete. What it does:

• Provides the primary grip point to open and close the microwave door
• Restores proper leverage and feel when the original handle is damaged
• Helps resolve issues like a loose, wobbly, or broken handle
• Improves appearance when the original handle is scuffed or cracked

• 1 door handle

• Disconnect power to the microwave before servicing.
• Protect the door/front panel from scratches; support it while working.
• Access and remove the handle's mounting screws/fasteners from the inner side of the door; transfer any spacers as needed.
• Hand-tighten mounting screws and ensure door opens/closes smoothly without binding.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged

This complete door assembly replaces a damaged or worn refrigerator door to restore proper sealing and operation. It comes preassembled to simplify replacement and help keep cold air inside for efficient cooling. What it does:

• Replaces a cracked, dented, or warped door to restore the unit's exterior fit and finish
• Helps re-establish a solid door seal to reduce temperature loss and frost buildup
• Restores proper door alignment and latching so the appliance opens and closes correctly
• Addresses visible damage and water/drip issues caused by door deformation

• One complete door assembly as shown

• Basic mechanical skill recommended; some disassembly of the cabinet and removal of trim may be required
• Keep power off and remove contents from the door before starting; support the door to prevent dropping
• Use appropriate tools to transfer hinges, gaskets, and any door-mounted components if not factory-installed
• If door-mounted electronics or ice/water components are present, verify electrical connections are disconnected and reconnected per OEM instructions

A full stainless replacement door assembly that restores the exterior appearance and function of compatible Frigidaire refrigerators. Replaces dented, scratched, or damaged doors for a clean, factory-fit finish and proper closure. What it does:

• Replaces a damaged or bent refrigerator door to restore proper sealing and alignment
• Restores the appliance's exterior appearance when the original door is dented or cosmetically worn
• Helps maintain correct internal temperature by allowing full door closure
• Works with existing hinges and trim when compatible with the model

• Disconnect power and remove food before starting any door repair
• Doors are heavy and can be awkward to handle—use a second person or proper support
• Some models require transfer of hinges, gaskets, handles, or trim from the old door; verify included items before installation

This high-voltage diode rectifies AC to DC in the microwave's high-voltage circuit so the magnetron can generate heat. When it fails, the oven may run normally but won't heat or may blow fuses.

• Converts high-voltage AC to DC for magnetron operation
• Maintains correct polarity and protects the HV circuit
• Common failure symptoms: runs but no heat, loud hum then shutdown, blown internal fuse, or tripping breaker
• Visible burn or damage on the diode or leads may be present

• Disconnect power before servicing; high voltage is present even when unplugged
• Safely discharge the high-voltage capacitor before touching HV components
• Match orientation to the original—polarity matters; ensure tight, insulated connections

This replacement Grille Assembly restores a clean, secure front cover for your appliance's vent/intake area. It helps protect internal components and maintain proper airflow while returning the unit to a finished, like-new appearance.

• Covers and protects the vent/intake opening at the front of the unit
• Helps maintain correct airflow through the appliance
• Replaces a cracked, warped, or missing grille that won't stay secured
• Can reduce rattling or vibration noises from broken tabs or a loose fit
• Restores the factory look and fit

• Disconnect power before servicing.
• Remove mounting screws/clips and support the grille while releasing tabs.
• Reuse existing hardware; align tabs and position the new grille, then secure.
• Tighten screws snugly—do not overtighten—and confirm proper alignment and clearance.

This thermostat is a temperature-sensitive switch used in select appliances to regulate heat or provide over-temperature protection. Replacing a failed thermostat restores consistent temperature control and helps protect internal components from heat-related damage.

• Monitors temperature at its mounting point and opens/closes the circuit at a factory-set threshold
• Regulates heating cycles or functions as a high-limit safety cutoff (application-dependent)
• Failure open can cause no heat or premature shutdown
• Failure stuck closed can lead to overheating, erratic temperatures, or extended run times

• Disconnect power and allow the appliance to cool before servicing
• Note wire locations; transfer one lead at a time to the new thermostat
• Mount flush and secure to the mating surface/bracket for accurate sensing; ensure firm terminal connections
• After installation, run and observe an initial cycle to confirm normal operation

This replacement plate is a structural component used to secure and support adjoining parts inside the appliance. Installing a new plate restores proper alignment and a solid mounting surface so connected pieces fasten correctly and operate smoothly. What it does:

• Provides a rigid base for mounting brackets, hinges, latches, or related hardware
• Maintains alignment to help doors, panels, or assemblies close and seal properly
• Replaces plates bent, cracked, or corroded from wear, impact, or over-tightening
• Typical symptoms: loose components, misalignment or gaps, vibration/rattling, or difficulty securing screws

• 1 plate

• Disconnect power; shut off gas and/or water before servicing
• Support adjacent parts before removing fasteners to prevent drops or misalignment
• Transfer original screws, spacers, or clips from the old plate to the new one
• Start screws by hand and tighten evenly; avoid over-tightening to prevent distortion

This rectifier is the microwave's high-voltage diode. It converts AC to DC in the high-voltage circuit so the magnetron can heat. Replacing a failed rectifier can restore reliable heating performance.

• Converts alternating current to direct current in the microwave's high-voltage circuit
• Works with the transformer and capacitor to power the magnetron
• A failed rectifier can cause no heat while the unit runs, intermittent heating, or unusual humming
• Blocks reverse voltage to help protect high-voltage components

• Disconnect power before servicing; microwaves contain high-voltage circuits
• The high-voltage capacitor can retain a dangerous charge even when unplugged—discharge per service procedures
• Observe polarity and match the original orientation during installation
• Route and secure leads as originally installed to avoid arcing or damage

Stainless panel with black touch pad.

The Glass Turntable Plate is an OEM part for Frigidaire microwaves. As the surface food rests upon during cooking, it features heat-resistant tempered glass construction suitable for high-power microwave usage. 

Causes of damage can include cracking or splitting from thermal shock of sudden temperature changes during repeated heating and cooling cycles. Improper cleaning methods using harsh chemicals may also degrade protective coatings.

Symptoms of a faulty glass plate involve: 

• Cracks or chips exposing sharp edges presenting a hazard
• Denting or warping preventing level rotation inside the cavity
• Staining or clouding compromising visibility of cooking foods

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore microwave models.