Frigidaire Refrigerator Ice Door Or Ice Chute

The Ice Door Bracket is an OEM part for Frigidaire refrigerators. It is a critical component of the ice dispenser mechanism, designed to support and align the ice door properly. This bracket ensures the ice door opens and closes smoothly, maintaining an airtight seal to prevent warm air from entering the freezer compartment and causing frost buildup.

Symptoms of a bad Ice Door Bracket include:

• The ice dispenser door failing to close completely, which can lead to ice melting and freezer burn.
• Excessive frost or ice accumulation near the dispenser area.
• Unusual noise when the dispenser is activated, indicating misalignment or instability.

Causes of a bad ice door bracket can include mechanical stress from repeated use, accidental damage from impact, or wear and tear that weakens the structural integrity of the bracket.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Door Seal is an OEM part for Frigidaire refrigerators. This seal is designed to create an airtight barrier around the ice dispenser door, preventing warm air from entering the freezer and maintaining optimal temperature inside the ice compartment. Please note, this listing is for the seal only, other components are sold separately.

Over time, the ice door seal can become worn out or damaged due to frequent use, exposure to varying temperatures, and regular opening and closing. Causes of a bad ice door seal include cracking, tearing, or loss of elasticity, which can lead to air leaks.

Symptoms of a bad ice door seal include:

• Frost or ice buildup around the ice dispenser
• Warm air entering the freezer compartment
• Increased energy consumption
• Water or condensation around the ice dispenser area
• The ice door not closing properly or sealing tightly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Door Center is an OEM part for Frigidaire refrigerators. This component is part of the ice dispenser system, managing the release of ice through the dispenser chute. It helps prevent cold air from escaping the freezer, maintaining energy efficiency and preserving the ice supply.

You should replace the ice door center if it becomes damaged or fails to seal properly. Causes of a bad ice door center can include regular wear and tear, damage from repeated use, or build-up of ice and debris obstructing its movement.

Symptoms of a bad ice door center include:

• Ice dispenser not working correctly
• Ice build-up around the dispenser area
• Warm air entering the freezer, causing ice to melt or clump
• Increased energy consumption due to poor sealing

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Dispenser Actuator Arm is an OEM part for Frigidaire refrigerators. It is designed to engage the ice dispensing mechanism when you press the lever or button on the ice dispenser. This actuator arm transfers the mechanical action needed to release ice from the dispenser into your glass or container.

You should replace the ice dispenser actuator arm if it becomes damaged, worn out, or fails to engage the ice dispensing mechanism properly. Common causes of a bad actuator arm include frequent use, mechanical wear, or accidental damage that can bend or break the arm.

Symptoms of a bad ice dispenser actuator arm include:

• The ice dispenser not releasing ice
• The dispenser lever feeling loose or unresponsive
• Ice dispenser making unusual noises
•  The actuator arm appearing bent or broken

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement ice container front is the front cover for the freezer's ice bucket. It restores a secure front wall so cubes stay contained and the bucket seats and dispenses correctly. What it does:

• Forms the front face of the ice container to keep ice contained
• Helps the bucket fit and align for proper dispensing
• Replaces a cracked, broken, loose, or missing front panel
• May help if ice spills from the bin or the bucket won't slide in or latch properly

• 1 ice container front (front cover only)

• Unplug the refrigerator and remove the ice bucket from the freezer
• Empty the bucket; transfer any screws, clips, or labels from the old front to the new part
• Align tabs and snap/fasten the new front to the bucket; do not overtighten screws
• Reinstall the bucket and check seating and dispenser operation

This replacement chute guides output through the appliance's passageway so it reaches the correct area. Replacing a cracked or warped chute restores smooth, consistent flow and helps prevent blockages, spills, and misdirected dispensing.

• Directs flow through the intended path between components
• Helps maintain alignment and sealing with adjoining parts
• Restores consistent dispensing/throughput when the original is damaged
• Common symptoms: visible cracks, obstructions, misalignment, or output missing the opening

• Disconnect power; turn off water supply if applicable
• Access the chute by removing the relevant cover or panel
• Transfer any reusable gasket/seal or mounting hardware from the old chute
• Seat and align the new chute fully; reassemble and test operation

This plug seals an unused hole in an appliance cabinet or inner liner to help block drafts, pests and moisture. It restores a clean, finished appearance and prevents accidental debris entry where a fitting or fastener is not used. What it does:

• Seals unused openings in the appliance cabinet or liner to keep out dust, moisture and pests
• Helps prevent air leaks that can affect temperature stability in refrigerators and freezers
• Covers exposed holes left after removing or relocating components or fasteners
• Restores a finished look to access areas and reduces risk of small-item ingress

• One cabinet sealing plug

• Push the plug into the hole until fully seated; no special tools usually required
• Turn off and unplug the appliance before reaching into compartments or behind panels
• Inspect the hole and plug for correct fit; replace if cracked or deformed

The Ice Maker Cooling Duct is an OEM part for Frigidaire refrigerators. It directs cold air flow to the ice maker.

Causes of failure can be blockages or damage to the duct over time that impact efficient air flow.

Symptoms of a bad cooling duct include:

• Inconsistently shaped or formed ice cubes
• Slow or reduced ice production
• The ice maker failing to dispense ice properly
• Higher than normal interior refrigerator temperatures near the ice maker

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models. 

Access door provides a finished cover for the appliance's service opening, protecting internal components from dust and damage while keeping the unit looking tidy and allowing access for maintenance and repairs. What it does:

• Covers the service or access opening and protects wiring, valves, and other internal parts.
• Allows access to controls, connections, or components for inspection and repair without removing major panels.
• Helps prevent debris, pets, or fingers from contacting internal parts.
• Replace a missing, cracked, or damaged access door to restore appearance and reduce exposure of internal components.

• Always disconnect power (and gas for gas appliances) before removing panels or working on the appliance.
• Handle the door and surrounding edges carefully to avoid cuts; keep original fasteners and reuse if undamaged.
• Align tabs/clips and secure with manufacturer screws; do not overtighten.

This ice door seals the freezer's dispenser chute to keep cold air in and block warm air and moisture out. It helps maintain proper ice dispensing and reduces icing or melting in the dispenser area. What it does:

• Seals the ice dispenser chute to prevent warm air intrusion and reduce ice clumping
• Opens to allow ice to pass when the dispenser is activated and closes to keep the bin insulated
• Helps prevent melted ice or water from entering the freezer cavity
• Reduces noisy or jammed dispensing caused by damaged or misaligned doors

• One ice door

• Disconnect power to the appliance before attempting any repair
• Inspect mounting tabs and hinges for damage; replace if worn to ensure proper sealing
• Handle plastic parts gently to avoid cracking; align door before tightening fasteners