Frigidaire Refrigerator Lever Parts

The Water Actuator is an OEM part for Frigidaire refrigerators. It is a crucial component of the dispenser system, primarily responsible for initiating the water dispensing process when pressed. This actuator typically sits behind the water dispenser lever on the refrigerator door, acting as the mechanical link that triggers the water flow when activated by the user.

Symptoms of a faulty water actuator include:

• Inability to dispense water when the lever is pressed.
• Intermittent or inconsistent water flow.
• Unusual noises during actuation.

Causes of a bad water actuator can include mechanical wear and tear, failure of the spring mechanism that returns the lever to its original position, or electrical issues that prevent the actuator from functioning properly. Regular usage and accidental impacts can also lead to the deterioration of this part.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Water Dispenser Actuator is an OEM part for Frigidaire refrigerators. It is responsible for activating the water dispenser when you press a glass or container against it, allowing water to flow from the dispenser.

You should replace this water dispenser actuator if it stops functioning properly. Causes of a bad actuator can include wear and tear from frequent use, damage from excessive force or impact, or electrical faults within the actuator mechanism.

Symptoms of a bad water dispenser actuator include:

• Water not dispensing when the actuator is pressed
• The actuator sticking or not returning to its original position
• Unusual noises when attempting to dispense water
• Water dispensing intermittently or uncontrollably

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Dispenser Lever is an OEM replacement part for Frigidaire refrigerators. This lever is a critical component of the refrigerator's water and ice dispenser system, located on the unit's exterior. It is designed to engage the dispenser when pressed, allowing for the seamless release of ice or water. 

Causes of a malfunctioning Dispenser Lever can include physical damage from impact, normal wear, and tear from repeated use, or a failure in the spring mechanism that could prevent it from returning to its off position. Maintaining this part in good working order is essential for its convenience.

Symptoms of a bad Dispenser Lever include:

• The dispenser fails to activate when the lever is pressed.
• The lever sticks in the pressed position or doesn't spring back.
• Difficulty in pressing the lever or it feels loose.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Ice Dispenser Actuator is an OEM replacement part specific to Frigidaire refrigerators. It is the electronic component responsible for actuating and operating the ice and water dispenser. 

Symptoms of a bad ice dispenser actuator include:

• The ice or water dispenser not working or dispensing intermittently  
• No signal or responsiveness from the dispenser button
• Ice cubes were dispensed incorrectly in large clumps instead of individually

Causes of failure can be related to wear and tear of moving parts over time, failures in the small electronic circuit board, or damage to wiring affecting power delivery to the actuator motor. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This refrigerator dispenser actuator is the paddle/lever you press with your glass to start ice or water dispensing. Replacing a cracked or worn actuator restores smooth operation and consistent switch engagement at the door dispenser.

• Engages the dispenser micro switch to initiate ice or water dispensing
• Provides the user-facing paddle/lever in the dispenser recess
• Helps the dispenser return to its rest position after you release
• Common symptoms: no dispense when pressed, intermittent response, broken/loose paddle, sticking or continuous dispense if jammed

• Unplug the refrigerator and shut off the water supply before servicing
• Carefully remove the dispenser trim/escutcheon to access the actuator; protect the finish and avoid breaking locking tabs
• Note spring and pivot orientation; transfer any reusable hardware to the new actuator
• Reassemble, restore power/water, and test both ice and water dispensing

Kit includes ice and water actuator arms.

This ice dispenser lever is the actuator you press with your glass to release ice from the freezer door. A worn or broken lever can keep the door dispenser from dispensing ice or make it hard to activate.

• Transfers your push at the dispenser pad to the ice dispenser switch
• Helps restore normal ice dispensing from the door chute
• Common symptoms: lever broken, loose, or stuck; no ice dispensed when pressed
• May cause intermittent dispensing if the actuator is worn or misaligned

• Unplug refrigerator before service; wear cut-resistant gloves
• Remove dispenser trim and control panel as needed to access the lever
• Note spring and pivot orientation; transfer any reusable hardware
• Test dispenser operation before reinstalling trim

This humidity control is the adjustable slider in the crisper drawer cover that opens and closes the vent to regulate moisture around fruits and vegetables. Replace a cracked or missing control to restore smooth adjustment and consistent crisper conditions.

• Mounts to the crisper cover and links to the vent/damper door
• Slides between settings to increase or reduce airflow for proper crisper humidity
• Typical symptoms: broken or missing lever, slider stuck or loose, vent doesn't move as you adjust, excess condensation or wilting produce

• Disconnect power; remove food, crisper pan, and cover/glass as needed—handle glass carefully
• Release the old control from its slot/retainer and note the vent linkage orientation
• Seat the new control and engage the linkage; confirm full travel and proper vent action
• Reassemble the cover and drawer, then restore power

This damper actuator controls the air damper that directs cold air between compartments, helping maintain consistent temperatures. Replacing a worn actuator restores regulated airflow and reduces uneven cooling or temperature swings. What it does:

• Moves the air/damper door to open or close the airflow path between freezer and fresh-food sections.
• Helps balance compartment temperatures by adjusting how much cold air is shared.
• A failing actuator can cause uneven cooling, temperature fluctuations, or reduced cold air in the fresh-food compartment.
• May make clicking noises or show no damper movement when faulty.

• Disconnect power to the appliance before starting any service.
• Access typically requires removing the damper housing or control cover in the fresh-food compartment.
• Align the actuator shaft with the damper linkage, seat the gear, and reconnect the electrical connector — do not force parts.

This actuator replaces the ice dispenser door motor that opens and closes the dispenser door so ice can drop into your cup. Restores proper door movement to help prevent ice blockages and missed dispenses. What it does:

• Drives the dispenser door to open and close when the dispenser is activated.
• Allows ice to release into the cup while keeping the dispenser sealed when idle.
• Common symptoms: dispenser door won't open, ice not dispensing, clicking or humming from the door area.
• Replaces a failed or intermittent dispenser door motor to restore normal dispensing action.

• Disconnect power to the appliance before beginning any repair.
• Replacement typically requires removing the inner dispenser/door panel; use common hand tools and keep track of fasteners.
• Inspect door linkage and wiring harness for damage when replacing the actuator.

This replacement actuator operates the refrigerator air damper to direct airflow between compartments, helping restore balanced temperatures and proper cooling when the damper won't move or air distribution is inconsistent. What it does

• Moves or positions the air damper to control airflow between the freezer and fresh-food sections.
• Helps correct uneven temperatures or poor cooling caused by a stuck or failed damper.
• Stops clicking or prevents the damper from remaining in one position when faulty.
• Works with the temperature control system to regulate compartment cooling as commanded.

• One actuator

• Always unplug the appliance before starting work to avoid electrical shock.
• Access usually requires removing interior panels or the control housing; keep track of screws and trim.
• Do not force plastic gears or tabs; verify alignment before securing the new actuator.
• Test damper operation and temperature response before reassembling interior panels.

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation

This dispenser actuator is a small internal lever in the refrigerator's door dispenser. It engages the switch/mechanism when you press the paddle, helping restore reliable ice or water dispensing and a firm, responsive feel at the dispenser.

• Transfers dispenser paddle movement to the ice/water switch
• If cracked or worn, ice or water may not dispense when pressed
• Dispenser paddle may feel loose, stick, or require extra force
• Can cause intermittent response at the dispenser

• Unplug the refrigerator and shut off the water supply before servicing
• Remove the dispenser trim/escutcheon and panel as directed by your model's instructions
• Replace the actuator, ensuring proper alignment with the switch and pivot points
• Reassemble, restore power, and test both ice and water dispensing

This actuator operates the refrigerator air damper to control airflow between compartments, helping maintain proper fresh-food and freezer temperatures. It replaces a failed or stuck damper motor to restore normal air circulation. What it does:

• Moves the air damper/blend door to regulate cold air flow into the fresh-food section
• Helps correct temperature imbalance symptoms like warm fresh-food compartment or overly cold freezer
• Replaces noisy, non-moving, or intermittently working damper actuators
• Works with the control board to position the damper as needed for cooling cycles

• One air damper actuator

• Disconnect power before servicing to avoid electrical shock
• Access usually requires removing interior panels or the control housing; handle trim and connectors gently
• Reconnect wiring and test damper operation with power restored; some models may require control board reset or calibration

Color: White