Frigidaire Refrigerator freezer is cold but refrigerator is warm: Common Causes & How to Fix

Repair Instructions:

The temperature control thermostat regulates voltage to the compressor, evaporator fan, and condenser fan to run the refrigeration system. A malfunctioning thermostat can disrupt proper operation, preventing the fridge from cooling properly. To check it, turn the thermostat from the lowest to highest setting listening for a clicking sound. Clicking indicates it's likely functional. No click means using a multimeter to check thermostat continuity. A thermostat without continuity at any setting is defective and needs replacement.

How to Replace a Frigidaire Refrigerator Temperature Control Thermostat:

1. Unplug the Frigidaire Refrigerator. Unplug the Frigidaire refrigerator from the electrical outlet to ensure your safety while working on the appliance.

2. Locate the Thermostat. Find the existing temperature control thermostat. It's often situated in the Frigidaire refrigerator's control panel, typically found in the upper section of the Frigidaire refrigerator compartment.
3. Disconnect Power to the Control Panel. In some cases, you may need to remove the control panel cover or housing to access the thermostat. Depending on your Frigidaire refrigerator model, this might involve removing screws or clips to detach the cover.
4. Note Wiring Connections. Take photographs or make a note of the wiring connections on the old thermosta for reconnecting the wires to the new thermostat.
5. Disconnect Wiring. Gently disconnect the wires and connectors from the old thermostat.
6. Remove the Old Thermostat. You may need to remove screws, clips, or brackets securing the old thermostat in place. Carefully remove these components to access the thermostat.
7. Install the New Thermostat. Position the new thermostat in the same location as the old one and secure it with screws, clips, or brackets.
8. Reconnect Wiring. Reattach the wires and connectors to the corresponding terminals on the new thermostat.
9. Reassemble the Control Panel. Reattach the control panel cover or housing, securing it with screws or clips.
10. Plug in the Frigidaire Refrigerator. After securely connecting the wiring and installing the new thermostat, plug the Frigidaire refrigerator back in or turn it on.
11. Set and Test the Thermostat. Adjust the thermostat to your desired temperature setting. It may take some time for the Frigidaire refrigerator to reach and stabilize at the desired temperature.

Repair Instructions:

Frigidaire Refrigerator door gaskets should seal tightly against the frame to retain cold air and block warm air. Twisted or torn gaskets can allow gaps that let warm air enter, causing the fridge to be warm while the freezer stays cold. Examine the gasket closely for rips or other damage. Replacing damaged gaskets restores the air-tight seal around the door.

How to Replace a Frigidaire Refrigerator Door Gasket:

1. Remove the Old Gasket. Open the Frigidaire refrigerator door and locate the screws or retaining clips securing the gasket to the door. Use a screwdriver to remove the screws or carefully release the clips.

2. Peel Off the Old Gasket. Carefully peel the old gasket away from the Frigidaire refrigerator door. If the gasket is stuck, you can use a hairdryer or heat gun to soften the gasket and make removal easier.
3. Clean the Door Surface. Wipe down the area where the old gasket was attached with a mild cleaning solution. Ensure it's free from any debris or residue.
4. Install the New Gasket. Align the new gasket with the door's edges, starting at one corner. Press the gasket firmly into place, following the path of the original gasket.
5. Secure the Gasket. Reattach the screws or clips that hold the gasket in place, making sure the gasket is snugly fitted against the door. Be cautious not to overtighten screws, as this could damage the gasket.
6. Check for Proper Seal. Close the Frigidaire refrigerator door and inspect the gasket to ensure it creates a proper seal. You should not see any gaps or feel air escaping when the door is closed.

Repair Instructions:

The defrost heater activates periodically to melt frost on the evaporator coils. If faulty, frost keeps building up and restricts airflow through the coils. This prevents proper cooling. Inspect the coils to see if excess frost has accumulated, indicating an issue. Test the heater and other defrost components if frost is present. The heater must work properly to regularly clear frost from the coils. Unrestricted airflow over the clear coils allows cold air to circulate and maintain cooling temperatures. Excess frost due to a malfunctioning defrost system will lead to insufficient fridge and freezer temperatures. Checking for frost accumulation helps identify if the defrost system needs attention.

Repair Instructions:

The evaporator fan circulates cold air over the coils and through the freezer and fridge. If not operating, cooling will be inadequate. Manually turn the fan blade to check for stuck rotation indicating a bad motor. Unusually loud operation also signals a faulty motor. Use a multimeter to test the motor windings if the fan doesn't run at all. No continuity means the motor is defective and needs replacing.

How to Replace a Frigidaire Refrigerator Evaporator Fan Motor:

1. Open the Frigidaire refrigerator and freezer doors. Remove any items, shelves, or drawers that obstruct access to the back wall of the freezer compartment.

2. Remove the freezer back panel. Locate the screws holding the back panel in place. Use the screwdriver or nut driver to remove these screws. Carefully pull the back panel away to expose the fan motor.
3. Disconnect Wiring. Identify the wiring connected to the fan motor. Gently disconnect the wires from the motor, taking note of their placement.
4. Unscrew the Motor. Using the appropriate tool, carefully remove any screws securing the fan motor to the bracket or housing.
5. Remove the Fan Blade. If the fan blade is attached to the old motor, carefully remove it.
6. Install the New Fan Motor. Position the new fan motor in the same location as the old one. Secure it in place with the screws you removed. If the fan blade was removed, attach it to the new motor.
7. Reconnect Wiring. Reconnect the wires to the new fan motor, ensuring they are correctly matched with their respective terminals.
8. Replace the Freezer Back Panel. Carefully position the back panel and secure it by reinserting and tightening the screws.
9. Reassemble the Freezer Compartment. Reinstall any shelves, drawers, and items you removed to access the fan motor.
10. Plug in the Frigidaire refrigerator. Check for proper functioning by feeling for airflow or listening for the fan running.

Repair Instructions:

The air damper regulates cold air flow into the Frigidaire refrigerator compartment. If it fails to open fully, inadequate chilled air enters causing insufficient cooling. Inspect the damper control to see if it is damaged or stuck in the closed position, preventing proper operation. The damper must freely open to the right amount to maintain optimal Frigidaire refrigerator temperatures. A broken or jammed damper disrupts vital cold air supply. Test the damper and replace if defective so it can appropriately open and close to release cold air as needed.

How to Replace Frigidaire Refrigerator Damper Control:

1. Safety Precautions:

   • Start by unplugging the Frigidaire refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Damper Control:

   • Identify the location of the damper control inside your Frigidaire refrigerator. It is usually found in the fresh food compartment, often at the back near the top.

3. Gather Necessary Tools and Replacement Parts:

   • Ensure you have the required tools such as a screwdriver and a compatible replacement damper control.

4. Access the Damper Control:

   • You may need to remove shelves or drawers in the fresh food compartment to access the damper control.

5. Disconnect Wiring:

   • Carefully disconnect the wiring or connectors attached to the old damper control. Take note of their positions for reconnection.

6. Unscrew or Unclip the Old Damper Control:

   • Use the appropriate tool, typically a screwdriver, to loosen and remove any screws or clips securing the old damper control. Be gentle to avoid damaging surrounding components.

7. Remove the Old Damper Control:

   • Gently slide out or lift the old damper control from its housing, taking care not to damage any wires or connectors.

8. Prepare the New Damper Control:

   • Unpack the replacement damper control and inspect it for any defects. Ensure it is clean and free from any packaging materials.

9. Install the New Damper Control:

   • Carefully position the new damper control in the same location as the old one, ensuring it fits securely and snugly.

10. Attach the Wiring:

    • Reconnect the wiring or connectors to the new damper control, following the same configuration as the old one.

11. Screw or Clip in the New Damper Control:

    • Secure the new damper control by reattaching any screws or clips you removed earlier. Ensure the control is firmly fastened in place.

12. Reassemble Shelves and Drawers:

    • If you removed any shelves or drawers to access the damper control, reassemble them in their original positions.

13. Plug In and Test:

    • Reconnect the Frigidaire refrigerator to the power source and monitor the operation of the new damper control. Ensure it regulates airflow as expected.

14. Final Check:

    • Inspect the new damper control to ensure it is properly installed and functioning, maintaining the desired temperature and airflow in your Frigidaire refrigerator's compartments. 

Repair Instructions:

The temperature sensor in a Frigidaire refrigerator provides key input to the control board to regulate cooling and keep set temperatures constant. If the sensor malfunctions, it can give incorrect temperature readings to the control board. This may lead to insufficient cooling being sent to the Frigidaire refrigerator compartment even as the freezer remains properly cold. Since the control board relies on the sensor input to determine how much refrigerant flow is needed, faulty readings from a bad sensor can restrict cold air circulation only to the Frigidaire refrigerator section. With inaccurate data, the board does not activate enough cooling to lower and maintain the appropriate temperature in the Frigidaire refrigerator.

How to Replace Frigidaire Refrigerator Temperature Sensor:

1. Safety Precautions:

   • Prior to any work, unplug the Frigidaire refrigerator to prevent any electrical accidents during the replacement process.
   • Empty the contents of the Frigidaire refrigerator and remove any shelves or items obstructing access to the temperature sensor.

2. Locate the Temperature Sensor:

   • Refer to the user manual or search online for the exact location of the temperature sensor in your specific Frigidaire refrigerator model.
   • Generally, it is situated near the evaporator coil or in the Frigidaire refrigerator compartment.

3. Remove the Sensor Cover:

   • Use a screwdriver to carefully detach the sensor cover, exposing the temperature sensor and other related components.
   • Keep track of the screws and store them in a secure place to prevent misplacement.

4. Detach the Old Temperature Sensor:

   • Identify the wires connected to the temperature sensor and take note of their positions.
   • Gently detach the wires by either sliding off the connectors or using pliers, depending on the type of connection.
   • Remove the old temperature sensor from its housing by carefully pulling it out.

5. Install the New Temperature Sensor:

   • Insert the new temperature sensor into the designated slot, ensuring a secure fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.

6. Replace the Sensor Cover:

   • Reattach the sensor cover by aligning it with the designated slots and securely tightening the screws.
   • Confirm that the cover is properly secured and adequately sealed.

7. Restore Power and Test:

   • Plug the Frigidaire refrigerator back into the power source.
   • Set the Frigidaire refrigerator to the recommended temperature and monitor its performance over the next few hours.
   • Ensure that the temperature sensor is accurately reading the temperature and that the Frigidaire refrigerator is cooling as expected.

8. Clean Up:

   • Dispose of any packaging from the new temperature sensor and return the Frigidaire refrigerator's contents to their original positions.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.

9. Final Check:

   • Double-check all connections and ensure that the sensor cover is securely fastened.
   • Confirm that the Frigidaire refrigerator is functioning smoothly and that the new temperature sensor has resolved any previous temperature regulation issues.

Always consult the specific user manual for your Frigidaire refrigerator model and consider seeking professional assistance if you are uncertain about the replacement process.

Repair Instructions:

The defrost control board regulates the frequency of defrost cycles. A failed board prevents cycles from running, allowing frost buildup on evaporator coils. Frosted coils make the Frigidaire refrigerator work harder to maintain cool temperatures. This can lead to inadequate cooling with compartments being too warm. First, verify proper operation of the defrost thermostat and heater. If those components function correctly, the likely issue is a defective control board needing replacement. The board manages to energize the defrost system to regularly clear coil frost.

How to Replace Frigidaire Refrigerator Defrost Control Board:

1. Safety Precautions:

   • Begin by unplugging the Frigidaire refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Defrost Control Board:

   • Identify the location of the defrost control board inside your Frigidaire refrigerator. It is often situated near the evaporator coils or within the appliance's control panel.

3. Gather Necessary Tools and Replacement Parts:

   • Ensure you have the required tools, such as a screwdriver or socket wrench, and acquire a compatible replacement defrost control board.

4. Access the Control Board:

   • Depending on your Frigidaire refrigerator model, you may need to remove a cover or panel to access the defrost control board.

5. Disconnect Wiring:

   • Carefully disconnect the wiring or connectors attached to the old defrost control board. Take note of their positions for reconnection.

6. Remove the Old Control Board:

   • Gently remove the old defrost control board from its mounting point, taking care not to damage the wires or connectors.

7. Prepare the New Control Board:

   • Unpack the replacement defrost control board and inspect it for any defects. Ensure it is clean and free from any packaging materials.

8. Install the New Control Board:

   • Carefully position the new defrost control board in the same location as the old one, securing it in place using the original mounting method.

9. Attach Wiring or Connectors:

   • Reconnect the wiring or connectors to the new defrost control board, following the same configuration as the old one.

10. Reassemble the Cover or Panel:

    • If you removed a cover or panel to access the control board, reassemble it in its original position.

11. Plug In and Test:

    • Reconnect the Frigidaire refrigerator to the power source and monitor the operation of the new defrost control board. Ensure it regulates the defrost cycle effectively.

12. Final Check:

    • Inspect the new defrost control board and its connections to ensure they are properly installed and functioning, contributing to the efficient defrosting of the evaporator coils in your Frigidaire refrigerator. 

Repair Instructions:

The door closing cam is a plastic or metal part located on the bottom edge of a Frigidaire refrigerator door. Its purpose is to properly align and seal the door when it is closed. The cam interacts with a strike plate on the Frigidaire refrigerator body to ensure the door is completely closed and the gasket forms an airtight seal. If the door closing cam is damaged or worn out, it may prevent the door from properly sealing when closed. This would allow warm air from the kitchen to leak into the Frigidaire refrigerator compartment while the freezer remains sealed and cold.

How to Replace Frigidaire Refrigerator Closing Cam:

1. Safety Precautions:

   • Begin by unplugging the Frigidaire refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Closing Cam:

   • Identify the location of the closing cam on the Frigidaire refrigerator door hinge. It is typically situated at the bottom of the door hinge.

3. Gather Necessary Tools and Replacement Parts:

   • Ensure you have the required tools, such as a socket or nut driver, and acquire a compatible replacement closing cam.

4. Open the Frigidaire Refrigerator Door:

   • Fully open the Frigidaire refrigerator door to access the closing cam and hinge.

5. Remove the Old Closing Cam:

   • Using the appropriate tool, typically a socket or nut driver, loosen and remove the screws securing the old closing cam. Take care not to damage the door or hinge during this process.

6. Detach the Closing Cam:

   • Carefully detach the old closing cam from the Frigidaire refrigerator door hinge. Be gentle to avoid damaging the hinge or any adjacent components.

7. Prepare the New Closing Cam:

   • Unpack the replacement closing cam and inspect it for any defects. Ensure it is clean and free from any packaging materials.

8. Install the New Closing Cam:

   • Carefully position the new closing cam onto the Frigidaire refrigerator door hinge, ensuring it aligns correctly with the hinge's mounting holes.

9. Secure the New Closing Cam:

   • Using the screws you removed earlier, secure the new closing cam to the hinge. Tighten the screws to ensure a snug fit.

10. Test the Door:

    • Gently close and open the Frigidaire refrigerator door to ensure the new closing cam operates smoothly and effectively.

11. Plug In and Test:

    • Reconnect the Frigidaire refrigerator to the power source and monitor the operation of the door with the new closing cam in place. Ensure it closes securely and maintains a proper seal.

12. Final Check:

    • Inspect the new closing cam to ensure it is properly installed and functioning, allowing the Frigidaire refrigerator door to close securely and maintain the desired temperature inside.

Repair Instructions:

The Frigidaire refrigerator fan motor circulates air between the freezer and Frigidaire refrigerator compartments to maintain even temperatures throughout. It is typically located underneath the fridge near the back and contains fan blades that spin to blow cold air from the freezer into the Frigidaire refrigerator section. If the fan motor stops working properly, it will not be able to move cold air to the Frigidaire refrigerator as efficiently. This allows the freezer to stay cold while the Frigidaire refrigerator warms up. A failed or failing fan motor may run slower, preventing adequate air circulation, or stop running completely.

How to Replace Frigidaire Refrigerator Fan Motor:

1. Safety Precautions:

   • Begin by unplugging the Frigidaire refrigerator from the power source to ensure your safety during the replacement process.

2. Locate the Fan Motor:

   • Identify the location of the fan motor inside your Frigidaire refrigerator. It is typically found in the freezer or fresh food compartment and may be behind panels or covers.

3. Gather Necessary Tools and Replacement Parts:

   • Ensure you have the required tools, including a screwdriver and a compatible replacement fan motor.

4. Access the Fan Motor:

   • Depending on your Frigidaire refrigerator model, you may need to remove covers, panels, or shelves to access the fan motor.

5. Disconnect Wiring:

   • Carefully disconnect the wiring or connectors attached to the old fan motor. Take note of their positions for reconnection.

6. Remove the Old Fan Motor:

   • Gently remove the old fan motor from its mounting point, being careful not to damage any wires, connectors, or surrounding components.

7. Prepare the New Fan Motor:

   • Unpack the replacement fan motor and inspect it for any defects. Ensure it is clean and free from any packaging materials.

8. Install the New Fan Motor:

   • Carefully position the new fan motor in the same location as the old one, securing it in place using the original mounting method.

9. Attach Wiring or Connectors:

   • Reconnect the wiring or connectors to the new fan motor, ensuring they are properly and securely attached.

10. Reassemble Covers or Panels:

    • If you removed any covers, panels, or shelves to access the fan motor, reassemble them in their original positions.

11. Plug In and Test:

    • Reconnect the Frigidaire refrigerator to the power source and test the operation of the new fan motor. Ensure it runs smoothly, effectively circulating air within the appliance.

12. Final Check:

    • Inspect the new fan motor and its connections to ensure they are properly installed and functioning, contributing to efficient cooling and air circulation in your Frigidaire refrigerator. 

Repair Instructions:

The Frigidaire refrigerator damper control assembly is a part that regulates airflow between the freezer and Frigidaire refrigerator compartments. It consists of a damper or door that can open and close via an electric motor to control the amount of cold air that flows from the freezer into the Frigidaire refrigerator section. If the damper control assembly is not functioning properly, it may fail to open the damper wide enough to allow sufficient cold airflow into the Frigidaire refrigerator side. This would result in the freezer staying cold as normal since it is directly cooled by the evaporator coils, while the Frigidaire refrigerator section would become warm due to inadequate cold air circulation.

How to Replace a Frigidaire Refrigerator Damper Control Assembly:

1. Locate the Damper Control Assembly. Identify the damper control assembly's location within the Frigidaire refrigerator. It's usually situated in the upper portion of the Frigidaire refrigerator compartment, typically behind a vent or a panel.

2. Remove Obstructions. Clear the Frigidaire refrigerator compartment of any items or shelves that might obstruct access to the damper control assembly.
3. Access the Damper Assembly. You may need to remove a vent cover, an air duct, or a panel that conceals the damper control assembly. Remove any screws or clips holding it in place.
4. Disconnect Wiring and Remove the Old Assembly. Carefully disconnect any wiring or connectors that are attached to the damper control assembly. Take note of how these are connected for reference when installing the new assembly. Remove any screws or fasteners holding the old damper control assembly in place.
5. Install the New Damper Control Assembly. Align the new damper control assembly in the same position as the old one. Secure it in place using the appropriate screws or fasteners, making sure it's tightly attached.
6. Reconnect Wiring. Reattach the wiring and connectors to the new damper control assembly, ensuring they match their original positions.
7. Replace Vent Cover or Panel. Reinstall the vent cover, air duct, or panel that conceals the damper control assembly. Secure it with screws or clips.
8. Reassemble the Frigidaire Refrigerator Compartment. Put back any shelves, items, or drawers you removed earlier to access the damper control assembly.
9. Plug In the Frigidaire Refrigerator. Plug in the Frigidaire refrigerator or turn it back on.
10. Test the Damper Control Assembly. Allow the Frigidaire refrigerator to run and cool for some time. Monitor the damper control assembly to ensure it opens and closes correctly, regulating the temperature and airflow within the Frigidaire refrigerator compartment.

Repair Instructions:

The thermistor monitors Frigidaire refrigerator temperature and relays readings to the control board. The board then regulates the compressor and evaporator fan based on the thermistor input to maintain proper cooling. A faulty thermistor can prevent necessary compressor and fan operation or cause excess running. Use a multimeter to test the thermistor. Resistance should vary with temperature changes. A thermistor with no resistance change or continuity is defective and needs replacing.

How to Replace Frigidaire Refrigerator Thermistor:

1. Prepare the Frigidaire Refrigerator:

   • Safely unplug the Frigidaire refrigerator to prevent any electrical accidents during the replacement process.
   • Empty the contents of the Frigidaire refrigerator and, if necessary, remove any storage shelves or drawers that might obstruct access to the thermistor.

2. Locate the Thermistor:

   • Refer to the user manual or search online for the precise location of the thermistor in your Frigidaire refrigerator model.
   • Typically, it is situated near the cooling coils, often behind the rear panel inside the Frigidaire refrigerator compartment.

3. Remove the Panel Cover:

   • Using a suitable screwdriver, carefully unscrew the panel cover to expose the thermistor and other internal components.
   • Keep track of the screws and store them in a secure location to prevent misplacement.

4. Disconnect the Old Thermistor:

   • Identify the thermistor and locate its connection point.
   • Gently detach the thermistor by either sliding off the connectors or using a pair of pliers, depending on the type of connection.

5. Install the New Thermistor:

   • Secure the new thermistor in the designated location, ensuring it is properly positioned and fixed.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.

6. Replace the Panel Cover:

   • Reattach the panel cover by aligning it with the designated slots and securely tightening the screws.
   • Ensure that the cover is firmly in place and properly sealed to prevent any potential issues.

7. Restore Power and Test:

   • Plug the Frigidaire refrigerator back into the power source.
   • Set the Frigidaire refrigerator to the recommended temperature and monitor its performance over the next few hours.
   • Ensure that the thermistor is accurately measuring the temperature and that the Frigidaire refrigerator is cooling as expected.

8. Clean Up:

   • Dispose of any packaging from the new thermistor and return the Frigidaire refrigerator's contents to their original positions.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.

9. Final Check:

   • Double-check all connections and ensure that the panel cover is securely fastened.
   • Confirm that the Frigidaire refrigerator is functioning smoothly and that the new thermistor replacement has resolved any previous temperature regulation issues.

Always consult the specific user manual for your Frigidaire refrigerator model and consider seeking professional assistance if you are uncertain about the replacement process.

Repair Instructions:

The defrost heater activates periodically to melt frost on the evaporator coils. A faulty heater prevents the defrost system from working properly. This allows frost to continually build up on the coils, leading to cooling issues where the freezer is cold but the Frigidaire refrigerator is warm. Use a multimeter to check the heater for electrical continuity, which signals it is working correctly. No continuity means the defrost heater is defective and should be replaced.

How to Replace a Frigidaire Refrigerator Defrost Heater Assembly:

1. Unplug the Frigidaire Refrigerator. Unplug the Frigidaire refrigerator from the electrical outlet to ensure your safety while working on the appliance.

2. Remove Items from Freezer. Empty the freezer compartment, removing all food items, shelves, and drawers that obstruct access to the rear panel.
3. Access the Defrost Heater. Carefully remove the rear panel or cover that conceals the defrost heater assembly. Remove screws or clips holding the panel in place.
4. Disconnect Wiring. Identify the wires or connectors attached to the old defrost heater assembly. Gently disconnect these wires, taking note of their positions for reference during reconnection.
5. Uninstall the Old Heater Assembly. Carefully remove the screws or clips securing the old defrost heater assembly to the evaporator coil.
6. Install the New Defrost Heater Assembly. Position the new defrost heater assembly in the same location as the old one, ensuring it's securely attached to the evaporator coil or mounting bracket.
7. Reconnect Wiring. Reattach the wires and connectors to the corresponding terminals on the new defrost heater assembly, making sure they match their original positions.
8. Replace the Rear Panel. Reinstall the rear panel or cover that conceals the defrost heater assembly, securing it with screws or clips.
9. Restore Items to the Freezer. Place back all the shelves, drawers, and food items you removed earlier from the freezer compartment.
10. Plug in the Frigidaire Refrigerator. After securely connecting the wiring and installing the new defrost heater assembly, plug the Frigidaire refrigerator back in or turn it on.
11. Monitor the Defrost Cycle. Allow the Frigidaire refrigerator to run for some time and observe the defrost heater assembly. It should periodically activate to melt ice on the evaporator coil.

Repair Instructions:

The temperature control board supplies power to the compressor and fan motors. A malfunctioning board can stop voltage supply, disabling cooling. However, control boards are often misdiagnosed. First test more failure-prone parts like the compressor and fans before the board. Replace those if defective instead of assuming board failure. Control boards have complex interactions with all refrigeration components. Premature board replacement costs time and money if another simpler part actually failed.

How to Replace Frigidaire Refrigerator Temperature Control Board:

1. Preparation:

   • Begin by unplugging the Frigidaire refrigerator to ensure your safety throughout the replacement process.
   • Empty the contents of the Frigidaire refrigerator and remove any items or shelves that might hinder access to the control board.

2. Locate the Control Board:

   • Consult the user manual or search online to pinpoint the exact location of the temperature control board within your specific Frigidaire refrigerator model.
   • Typically, it is situated behind the control panel or at the back of the Frigidaire refrigerator.

3. Remove the Control Panel:

   • Using a suitable screwdriver, carefully detach the control panel from the Frigidaire refrigerator's exterior.
   • Keep track of the screws and store them in a safe place to prevent loss or misplacement.

4. Disconnect Wires and Remove the Old Control Board:

   • Identify the wires attached to the control board and take note of their positions.
   • Gently detach the wires by either sliding off the connectors or using a pair of plier, depending on the connection type.
   • Remove the old temperature control board from its housing by carefully pulling it out.

5. Install the New Control Board:

   • Place the new control board into the designated slot, ensuring a snug fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.

6. Replace the Control Panel:

   • Reattach the control panel by aligning it with the appropriate slots and securely tightening the screws.
   • Verify that the panel is properly secured and firmly in place.

7. Restore Power and Test:

   • Plug the Frigidaire refrigerator back into the power source.
   • Set the temperature control to the recommended level and monitor the Frigidaire refrigerator's performance over the next few hours.
   • Ensure that the control board is effectively regulating the temperature and that the Frigidaire refrigerator is cooling as expected.

8. Clean Up:

   • Discard any packaging from the new control board and return the Frigidaire refrigerator's contents to their original positions.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.

9. Final Check:

   • Double-check all connections and ensure that the control panel is securely fastened.
   • Confirm that the Frigidaire refrigerator is functioning smoothly and that the new temperature control board has resolved any previous temperature regulation issues.

Always refer to the specific user manual for your Frigidaire refrigerator model and consider seeking professional assistance if you are uncertain about the replacement process.

Repair Instructions:

The defrost thermostat monitors the evaporator coil temperature. Below a set point, it closes to power the defrost heater and melt any frost buildup during defrost cycles. A faulty thermostat prevents heater activation, allowing coil frost accumulation. This can cause uneven cooling with a cold freezer but a warm Frigidaire refrigerator. Use a multimeter to check the thermostat's electrical continuity at low operating temperatures. No continuity signifies a defective thermostat needing replacement.

How to Replace Frigidaire Refrigerator Defrost Thermostat:

1. Preparation:

   • Unplug the Frigidaire refrigerator from the power source to ensure safety.
   • Empty the contents of the freezer and remove any shelves or compartments obstructing access to the back panel.

2. Locate the Defrost Thermostat:

   • Consult the user manual or search online for the specific location of the defrost thermostat in your Frigidaire refrigerator model.
   • Typically, it is positioned near the evaporator coils at the back of the freezer compartment.

3. Remove the Panel Cover:

   • Using a screwdriver, carefully unscrew the panel cover that shields the thermostat and other components.
   • Keep track of the screws and store them in a secure place to avoid misplacement.

4. Disconnect Wires and Remove the Defrost Thermostat:

   • Identify the wires attached to the defrost thermostat.
   • Gently detach the wires by either sliding off the connectors or using a pair of pliers, depending on the connection type.
   • Remove the defrost thermostat from its housing by carefully pulling it out.

5. Install the New Defrost Thermostat:

   • Place the new defrost thermostat into the housing, ensuring a secure fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.

6. Replace the Panel Cover:

   • Reattach the panel cover by aligning it with the designated slots and carefully tightening the screws.
   • Verify that the cover is secure and properly sealed to prevent any potential issues.

7. Restore Power and Test:

   • Plug the Frigidaire refrigerator back into the power source.
   • Set the thermostat to the appropriate temperature setting and monitor the freezer's performance over the next few hours.
   • Ensure that the defrost cycle is functioning correctly and that the thermostat is regulating the temperature as intended.

8. Clean Up:

   • Dispose of any packaging from the new thermostat and return the freezer's contents to their original places.
   • Wipe down the area to remove any dust or debris that may have accumulated during the replacement process.

9. Final Check:

   • Double-check all connections and ensure that the panel cover is securely fastened.
   • Confirm that the Frigidaire refrigerator is operating smoothly and that the defrost thermostat replacement has resolved any previous issues.

Always consult the specific user manual for your Frigidaire refrigerator model and consider seeking professional assistance if you are uncertain about the replacement process.

Repair Instructions:

The compressor is the component responsible for pumping refrigerant through the cooling system and enabling heat exchange in a Frigidaire refrigerator. If the compressor is not functioning properly, it will fail to circulate refrigerant and provide cooling adequately. Since the freezer compartment is closest to the evaporator coils, it may still receive some cooling from weakened refrigerant flow and remain cold. However, inadequate refrigerant circulation from a faulty compressor will prevent sufficient cooling from reaching the Frigidaire refrigerator compartment. Only an EPA-certified technician should replace sealed system components. 

Repair Instructions:

The filter drier is a component in the Frigidaire refrigerator's sealed cooling system that filters out moisture and contaminants. It contains desiccant beads or other material to absorb moisture in the refrigerant circulated through the coils. Over time, the filter drier can become obstructed with debris or saturated with moisture, reducing its effectiveness at drying the refrigerant. A malfunctioning filter drier allows excessive moisture to build up in the system. This moisture can freeze and block refrigerant flow at the capillary tube, restricting cold air from reaching the Frigidaire refrigerator compartment. Only an EPA-certified technician should replace the drier filter, as it is part of the sealed system. 

Repair Instructions:

The main control board seems like a potential issue but is rarely the true problem. First methodically test more failure-prone parts before the board itself. Only replace the board after confirming the proper operation of fans, thermistors, switches, and other electrical parts.

How to Replace Frigidaire Refrigerator Main Control Board:

1. Safety Measures:

   • Start by unplugging the Frigidaire refrigerator to avoid any electrical mishaps during the replacement process.
   • Remove all items from the Frigidaire refrigerator and clear any obstacles that may impede access to the control board.

2. Locate the Control Board:

   • Refer to the user manual or search online for the precise location of the main control board in your specific Frigidaire refrigerator model.
   • Typically, the control board is positioned behind the control panel or at the back of the Frigidaire refrigerator.

3. Remove the Control Panel:

   • Using an appropriate screwdriver, carefully detach the control panel from the Frigidaire refrigerator's exterior.
   • Ensure to keep track of the screws and store them in a secure place to prevent misplacement.

4. Disconnect Wires and Remove the Old Control Board:

   • Identify the wires connected to the control board and note their positions.
   • Gently disconnect the wires by sliding off the connectors or using pliers, depending on the type of connection.
   • Remove the old main control board from its housing by carefully pulling it out.

5. Install the New Control Board:

   • Place the new control board into the designated slot, ensuring a snug and secure fit.
   • Reconnect the wires to the corresponding terminals by firmly pressing them into place.

6. Replace the Control Panel:

   • Reattach the control panel by aligning it with the appropriate slots and securely tightening the screws.
   • Confirm that the panel is properly secured and tightly in place.

7. Restore Power and Test:

   • Plug the Frigidaire refrigerator back into the power source.
   • Set the Frigidaire refrigerator to the recommended settings and monitor its performance over the next few hours.
   • Ensure that the control board is effectively managing the Frigidaire refrigerator's functions and that it is operating as expected.

8. Clean Up:

   • Dispose of any packaging from the new control board and return the Frigidaire refrigerator's contents to their original positions.
   • Wipe down the area to eliminate any dust or debris that may have accumulated during the replacement process.

9. Final Check:

   • Double-check all connections and ensure that the control panel is securely fastened.
   • Confirm that the Frigidaire refrigerator is functioning smoothly and that the new main control board has resolved any previous issues.

Always refer to the specific user manual for your Frigidaire refrigerator model and consider seeking professional assistance if you are uncertain about the replacement process.

Repair Instructions:

The control board may seem faulty but is rarely the true issue. First methodically verify proper operation of more failure-prone parts like fans, sensors and switches before the board. Only replace it after confirming no other electrical components are malfunctioning.

How to Replace a Frigidaire Refrigerator Control Board:

1. Unplug the Frigidaire Refrigerator. Unplug the Frigidaire refrigerator from the electrical outlet to ensure your safety while working on the appliance.

2. Locate the Control Board. Identify the current control board, typically located in the Frigidaire refrigerator's control panel, which is often located on the front of the appliance, near the top or inside the Frigidaire refrigerator section.
3. Document Wiring Connections. Take photographs or make a detailed note of the wiring connections on the old control board for correctly reconnecting the wires to the new control board.
4. Disconnect Wiring. Gently disconnect the wires and connectors from the old control board.
5. Remove the Old Control Board. You may need to remove screws, clips, or retaining brackets securing the old control board. Carefully remove these components to access the control board.
6. Install the New Control Board. Position the new control board in the same location as the old one and secure it with screws, clips, or brackets.
7. Reconnect Wiring. Reattach the wires and connectors to the corresponding terminals on the new control board.
8. Plug in the Frigidaire Refrigerator. Allow the Frigidaire refrigerator to run for a while. Test the control board's functionality by adjusting temperature settings, ensuring that it properly regulates the Frigidaire refrigerator's temperature and features like defrost cycles.

Repair Instructions:

Doors not closing completely can reduce Frigidaire refrigerator cooling. Check if door bins are obstructing closure by hitting shelves. Also verify items in bins and on shelves aren't keeping the door partially open. Ensure all interior components are properly positioned to allow full door closure. Overfilled bins and shelves can also prevent the door sealing tightly. Take steps to avoid overloading interior storage space. Proper door alignment and avoiding overpacking allows complete closure so the sealed door maintains desired cooling temperatures inside the Frigidaire refrigerator.