Frigidaire Refrigerator Shaft Or Pin

This auger drive bar links the dispenser motor to the ice bucket auger, transmitting torque to move cubes or crushed ice to the chute. Replacing a worn or stripped bar restores consistent, reliable ice dispensing. What it does:

• Couples the dispenser motor to the auger/crusher assembly
• Transfers rotation so ice advances to the dispenser chute
• Interfaces with the cube/crush selector mechanism
• Common symptoms include the motor running but no ice dispensing, intermittent dispensing, the auger not turning, or grinding/clicking from the dispenser

• 1 auger drive bar

• Disconnect power and remove the ice bucket before servicing
• Note the bar's orientation; remove any retainers and separate it from the yoke/coupler
• Align the new bar with the mating parts and seat it fully; transfer any reusable retainers
• Reinstall the bin and test both cube and crush selections

This is the drive gear for the ice maker module. It transfers motor power to the ejector/harvest mechanism so cubes release consistently; worn or stripped teeth can cause clicking, stalls, or little to no ice production.

• Transfers motor torque to rotate the ejector and complete the harvest cycle
• Replaces a cracked, stripped, or worn gear that prevents proper ice ejection
• Typical symptoms: no ice production, icemaker stuck mid-cycle, clicking or grinding from the module
• Helps restore reliable ice maker cycling

• Unplug the refrigerator before service; turn off the water supply if moving the icemaker
• Remove the icemaker assembly for access; note the original gear's orientation before removal
• Align the new gear with the shaft; do not force it—inspect mating parts for wear
• After reassembly, verify the ejector turns freely; restore power and run a test cycle

This door bin guard secures items on a refrigerator door shelf, preventing bottles and containers from sliding out. Replace it when cracked or missing to restore safe, usable door storage. What it does:

• Mounts to the front of a door bin to hold contents in place
• Replaces a broken, warped, or missing guard
• Helps resolve issues like items falling from the door shelf or a loose/broken bar
• Restores usable door storage space

• 1 door bin guard

• Unplug the appliance or disconnect power before servicing
• Empty the affected bin; release the old guard and align/snap the new guard into the slots
• Let cold plastic warm to room temperature before installation to reduce the risk of cracking
• The guard is fully seated before reloading items

This replacement gear restores the transfer of motion inside the refrigerator's mechanism so the assembly operates smoothly and reliably. Designed to match the original fit and drive characteristics for consistent performance.

• Transmits rotation between mating shafts/components within the assembly
• Worn or stripped teeth can cause stalling, slipping, or clicking/grinding noises
• Visual inspection often reveals rounded, cracked, or missing teeth

• Disconnect power before servicing
• Note the original gear's orientation and any timing/alignment marks before removal
• Transfer any clips, spacers, or washers from the original part as needed
• Inspect mating gears/shafts for wear and replace related parts to prevent repeat failure

This spiral pin secures components in place within the appliance assembly, providing a tight, durable fit that resists loosening under normal operation. Replacing a worn or missing pin helps restore proper alignment and dependable drive of the linked parts.

• Holds mating parts together with a press-fit connection
• Can help resolve issues like loose or slipping drive components, rattling, or intermittent operation in the affected mechanism
• Maintains correct alignment to reduce wear on adjoining parts

• Disconnect power and shut off water before servicing
• Support the assembly to relieve tension before removing the old pin
• Use the correct size punch/driver to press the pin out and in straight
• Do not force; inspect mating parts for wear and replace if damaged

This replacement bar is a direct-fit support component that helps hold and stabilize a refrigerator door or interior shelf assembly, restoring secure storage and preventing items from shifting or falling. What it does

• Provides structural support for a door or shelf ledge to keep stored items secure
• Replaces bent, cracked or broken bars that allow shelves or door bins to sag
• Helps stop rattling or movement from loose or damaged supports
• Restores proper alignment so shelves and bins sit flush and stable

• One replacement bar

• Disconnect power before removing refrigerator doors or interior components when necessary
• Remove affected shelf or bin to access mounting points
• Use basic hand tools; avoid overtightening fasteners to prevent cracking plastic parts
• Handle glass shelves and door bins carefully during removal and reassembly

A small push-fit plastic retainer used to secure interior trim, panels, or lightweight components. Keeps parts held in place without screws for a clean finish and quick replacement. What it does

• Acts as a push-in fastener to hold trim pieces, liners, or lightweight panels.
• Replaces worn, broken, or missing pins that allow interior parts to shift or rattle.
• Helps stop loose trim, sagging panels, or gaps that can collect dirt or cause noise.
• Simple, non-threaded design for a secure press-fit connection.

• Press firmly into the matching hole until fully seated; do not force beyond resistance.
• Inspect mating hole for damage or debris before installing to ensure a proper fit.
• Use basic hand tools (needle-nose pliers) only if needed to remove the old pin; avoid prying against fragile trim.
• If the original hole is stretched or cracked, replace the mating trim or panel to regain proper retention.

This control rod is a direct-replacement linkage rod that connects a user control to the appliance's internal mechanism, restoring reliable mechanical movement and control operation. What it does:

• Transfers motion from an external control lever or knob to the internal mechanism
• Replaces a bent, worn, or broken linkage that causes sticky or non-responsive controls
• Helps restore proper engagement and consistent mechanical action
• Works as a simple mechanical replacement—no electronic programming required

• One control rod

• Disconnect power (and gas if applicable) before beginning any repair
• Basic hand tools may be required; follow the appliance service manual for disassembly steps
• Handle small parts carefully to avoid damage and ensure proper alignment during reassembly

This compressor mounting pin secures the refrigerator compressor to its mounting bracket, helping reduce vibration and noise for reliable operation. It's a simple, rugged fastener used where the compressor meets the cabinet base. What it does:

• Anchors the compressor to the mounting bracket to limit movement and vibration
• Helps reduce compressor-related rattling or banging noises during operation
• Maintains proper compressor alignment to protect refrigerant lines and electrical connections
• Works with existing mounts and brackets as shown in OEM diagrams

• One compressor mounting pin

• Disconnect power and unplug the appliance before accessing the compressor area
• Support the compressor and attached lines before removing or installing mounting hardware
• Use appropriate hand tools and follow OEM diagram locations for correct placement