Frigidaire Refrigerator Wire, Harness, Power Cord

The Power Cord is an OEM part for Frigidaire refrigerators. It transmits electrical current from the wall outlet directly to the internal refrigerator components, allowing them to operate properly. As the critical link supplying energy, this power cord plays an essential role in refrigerator performance.

Causes can involve normal wear over many years, accidental punctures, harsh chemicals, or excessive bending/pulling that strains and weakens internal wiring. Rodent damage is another potential issue.

Symptoms of a bad power cord include:

• The refrigerator not powering on when plugged in
• Flickering lights or intermittent operation
• Warm temperatures inside the fridge compartment
• Evidence of cord damage like cracks, blisters, or exposed wires

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement power cord delivers household electricity from the outlet to your appliance. Installing a new cord restores safe, reliable power when the original is damaged, worn, or causing intermittent operation.

• Supplies AC power from a household outlet to the unit
• Common fix for no power, flickering lights, or power loss when the cord is moved
• Replaces cords with cuts, cracks, burn marks, or melted areas
• Restores a secure electrical connection for safe, consistent operation

• Unplug the appliance and verify the wall outlet is working before replacing parts
• Access the cord routing and internal connections; note wire positions and routing before removal
• Transfer and secure any strain relief/clamp; keep wiring clear of sharp edges and hot surfaces
• After installation, ensure the cord isn't pinched and the plug seats fully in the outlet

The Power Cord is an OEM replacement part for Frigidaire refrigerators. As the lifeline connecting the appliance to a wall outlet, this cord safely delivers necessary voltage to operate refrigerator systems. 

Potential causes for needing a new power cord include exposure to cuts, abrasions or rodent damage over time in the storage area. Repeated bending stress during installation or removal can also wear out plastic insulation faster.

Symptoms of a faulty power cord include: 

• Refrigerator fails to power on at all
• Flickering lights or inconsistent runs of the compressor  
• Shock, buzzing or humming sounds coming from the cord
• Bare copper wire showing through damaged insulation

This power cord also fits some Electrolux and Gibson refrigerators.

A wiring harness that routes power and signals between a refrigerator's internal electrical components, helping lights, controls, fans and motors operate correctly. Replacing a damaged harness restores reliable electrical connectivity and reduces risk of intermittent faults. What it does:

• Routes power and signal connections between the control board, lights, motors, sensors and other internal components.
• Common visible issues include frayed insulation, broken or loose connectors, or heat damage at terminals.
• Replacing a faulty harness helps eliminate wiring-related faults that can cause component failures or safety concerns.

• Always disconnect power (unplug appliance or shut off circuit breaker) before inspecting or replacing the harness.
• Match connector shapes and pin counts; route the harness along the original path and avoid tight bends or pinch points.
• Secure with the existing clips or ties; replace damaged clips or protective insulation as needed.

This control box wiring harness routes power and signals between the appliance control board and other components to restore reliable control operation and electrical connectivity. It helps resolve intermittent controls and lost function caused by damaged wiring. What it does:

• Connects the control board to switches, sensors and motors to enable normal control functions.
• Replaces damaged or frayed wiring that can cause intermittent operation or unresponsive controls.
• Addresses symptoms such as control panel not responding, random shutdowns, or error codes tied to wiring faults.
• Restores proper signal and power routing when connector damage or wire breaks interrupt circuits.

• Disconnect all power to the appliance before beginning any service.
• Compare the new harness to the original and follow factory connector positions and routing to avoid pin miswiring or chafing.
• Handle connectors gently and ensure all terminals fully seat; inspect mating connectors for damage before reconnecting.

This wiring harness routes power and signal connections between components to restore proper electrical communication and operation. It replaces a damaged or worn harness to fix intermittent or failed electrical functions. What it does:

• Reconnects power and control circuits between components so systems can receive proper voltage and signals
• Commonly used when wiring is frayed, burned, pinched, or connectors are loose or corroded
• Can resolve symptoms like no power to a component, intermittent operation, or control not responding
• Restores secure plug-and-play connections when the original harness is damaged

• Wiring harness assembly

• Always disconnect power before replacing any wiring or electrical parts
• Inspect connector fit, wire routing, and strain reliefs; route harness the same way as the original to avoid pinching
• Make sure connectors are fully seated and any locking tabs engage
• If you see damaged connectors on the appliance side, repair those before connecting the new harness

This wiring harness connects the appliance's control board or power source to internal components, restoring electrical continuity for reliable operation. Replace a damaged harness to stop intermittent power or non-responsive functions. What it does

• Routes power and signals between the control and components so controls, switches and motors operate correctly.
• Common symptom: controls or display are unresponsive or intermittent.
• Common symptom: specific functions (motors, lights, heating elements) do not receive power.
• Helps prevent shorts and arcing when routing and insulation are intact.

• One wiring harness as pictured and specified by the manufacturer.

• Disconnect power (unplug or shut off breaker) before accessing internal wiring.
• Verify connector orientation and seating; match wire colors and terminal positions during reassembly.
• Replace only the harnesses explicitly listed for your exact model to avoid mis-wiring.
• If you see burned terminals or damaged connectors, inspect adjacent components and replace as needed.

This Mullion harness routes electrical connections through the refrigerator door mullion so lights, sensors and control/LED assemblies communicate with the main cabinet wiring. It restores reliable power and signal routing in the door center strip. What it does:

• Carries power and signal between the door/mullion components and the main harness
• Restores non-functioning mullion lights, LEDs or control communication caused by a damaged harness
• Prevents intermittent connections from frayed or broken mullion wiring
• Used when visible wire damage or connector failure is found in the mullion area

• One (1) mullion harness as pictured

• Disconnect power to the appliance before starting work to avoid shock or injury
• Remove the mullion/door trim and any gaskets per service instructions to access the harness
• Inspect connectors and wire routing; replace any clips or retainers to prevent pinching

This dispenser wiring harness connects the dispenser controls and components in the refrigerator door, restoring electrical continuity for the dispenser functions and simplifying replacement of a damaged or faulty harness. What it does:

• Carries power and signals between the dispenser switches, valve/solenoid, and indicator lights
• Replaces frayed, pinched, or damaged wiring that can cause intermittent or no dispenser operation
• Addresses symptoms like non-working water/ice dispenser, no dispenser lights, or unresponsive dispenser switches
• Provides factory-style connectors for a direct, plug-and-play replacement

• One dispenser wiring harness

• Disconnect power to the appliance before beginning any work to avoid shock
• Remove the inner door panel or dispenser bezel per your model's service instructions to access the harness
• Match connectors and routing to the original harness; avoid stretching or pinching wires when reinstalling
• Test dispenser functions after installation and reassemble panels securely

This replacement electrical wire restores a single conductor connection used in your appliance's wiring system, helping re-establish power or signal continuity where the original lead is damaged. What it does

• Replaces a single appliance electrical lead to restore lost connection or repair damaged insulation.
• Used to carry power or control signals between components.
• Common symptom: intermittent or no power to a component, visible frayed or broken wire.
• Matches original part function and routing; intended for direct replacement.

• One replacement electrical wire (single lead).

• Disconnect power to the appliance before starting any repairs to avoid shock.
• Verify wire routing and secure connections match the original; use proper wire connectors and insulation.
• If soldering or crimping is required, follow manufacturer guidelines and use proper tools.