Frigidaire Wall Oven Heating Element

The Broil Heating Element is an OEM part for Frigidaire ranges. Located inside the oven compartment, it provides heat energy for the broil cooking function. 

Causes of a bad broil element can include mineral buildup over time, surface corrosion or internal wire fatigue from ongoing temperature cycling.

Symptoms of a bad broil element include:

• Inadequate or uneven broiling temperatures
• Element failing to glow red or turn on fully
• Burning or charring of foods below the element
• Oven display showing error code related to element failure

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This electric heating element restores consistent, reliable heat in your appliance, so cooking or warming functions work as intended. Replace a failed element to eliminate slow heat-up, uneven temperatures, or no-heat conditions.

• Converts electrical power into heat for the appliance's designated cavity or surface
• Common failure symptoms: no heat, uneven heating, very slow preheat/warm-up
• Visual clues: breaks, blisters, or hot spots on the coil
• May cause the unit to cycle erratically or trip a breaker if shorted

• Disconnect power at the breaker or unplug before servicing; allow all components to cool
• Wear cut-resistant gloves; avoid bending or kinking the element
• Photograph wiring and transfer connectors one-for-one; ensure tight, clean terminal fits
• Inspect wires/terminals for heat damage and replace any compromised connectors

This broil element mounts at the top of the oven cavity and delivers radiant heat for broiling and top-browning. Replace a broken or burned-out element to restore consistent broil performance.

• Emits high, radiant heat from the top of the oven during the broil cycle
• Used to sear and top-brown foods
• Replaces the original broil element on compatible units
• Common symptoms: No heat in broil, element won't glow, uneven top browning, visible cracks/blistering on the element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; support the element while removing mounting screws
• Carefully pull the element forward and disconnect the wire terminals; avoid bending the element
• Attach the new element, secure with screws, ensure it is clear of the oven liner, then restore power and test

The Surface Element is an OEM part for Frigidaire electric ranges. As the key heating component on the cooktop, the surface element produces heat through resistance when electrical current flows through it.

Causes can be normal wear over time exposed to heat cycles, damaged or degraded internal components, corrosion of terminals or wires, or surface damage from improper cleaning.

Symptoms of a bad surface element include:

• Slow or uneven heating
• Burning or scorching of cookware easily
• Element that will not heat at all or only reaches low temperatures
• Frayed, cracked, or broken wiring at the element terminal

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Broil Element is an OEM replacement part for  Frigidaire electric ranges. It is an electric heating component located at the top of the oven used for broiling food. The broil element generates intense radiant heat from above, allowing food to brown and crisp up while also cooking from direct heat exposure. It is crucial for the broil cooking function. 

Symptoms of a bad broil element include:

• The broil feature failing to get the oven hot enough or working inconsistently
• Discoloration, rusting, or other signs of deterioration on the element  
• Tripping of the circuit breaker or thermostat when using broil
• Food not browning or crisping up as expected under the broiler

Causes can be standard wear and tear over many heating and cooling cycles or damage from cleaning products or spatters inside the oven.

This OEM Frigidaire replacement part is also compatible with some Electrolux, Westinghouse, and Kenmore electric ranges.

This oven bake element supplies the lower-oven heat for Bake cycles. Replacing a failed element restores proper preheating and consistent temperatures so your electric range or wall oven bakes reliably again. What it does:

• Provides radiant heat from the bottom of the oven during Bake
• Helps the oven reach and maintain the set temperature
• Failure symptoms can include: no heat in Bake, very slow preheating, uneven baking, or the element not glowing
• Visible damage such as breaks, blisters, or burned spots indicates replacement is needed

• One bake element

• Disconnect power at the breaker before servicing
• Remove oven racks; unfasten the element's mounting screws, then gently pull the element forward and transfer the wires one at a time
• Reuse existing mounting hardware; ensure terminals are fully seated and not contacting the oven cavity
• Restore power and test Bake; the element should heat evenly

This bake element supplies the primary heat from the bottom of the oven cavity during Bake mode, delivering even, reliable cooking. Replacing a failed element restores proper preheat and consistent temperatures. What it does:

• Provides bottom-oven heat in Bake to reach and maintain the set temperature
• Helps ensure even baking and roasting across racks
• Typical failure symptoms: no heat in Bake, very slow preheat, uneven or undercooked results
• Visual clues: blistering, cracks, or a burned-through spot on the element

• One bake element

• Disconnect power at the breaker and allow the oven to cool completely
• Remove racks; take out the element's mounting screws and gently pull the element forward
• Transfer the two wires to the new element one at a time; do not let wires slip back into the insulation
• Reinstall the element and screws, restore power, and test for proper heating

This broil element mounts at the top of the oven cavity and provides high, radiant heat for broiling and top-browning. Replace it if the broiler won't heat, heats unevenly, or the element shows visible damage.

• Delivers intense, top-down radiant heat for broiling and finishing dishes
• Restores broil performance when the original element is open, shorted, or weak
• Common symptoms: no broil heat, only part of the element glows, uneven browning, visible blisters/cracks, tripping the breaker
• Direct replacement designed to fit and connect to existing terminals

• Disconnect power at the breaker or unplug the range before servicing; high-voltage hazard
• Remove oven racks; take out element mounting screws and carefully pull the element forward to access terminals
• Transfer wires one at a time and support them to prevent retracting into the insulation; ensure tight, clean connections
• Reinstall screws, restore power, and test broil for an even, consistent glow

This dual surface element restores steady, selectable heat to a cooking zone on your electric range or cooktop. It provides two heating areas in one burner position so you can match heat output to small or larger cookware.

• Heats cookware by energizing the inner ring alone or both inner and outer rings together
• Helps resolve issues such as a surface burner not heating, only one ring heating, or intermittent/uneven heat
• Replaces a cracked, blistered, or visibly damaged element to restore reliable performance

• Disconnect power at the breaker and allow the cooktop to cool completely before servicing
• Access the element from beneath the cooktop; photograph wire locations for reference
• Carefully transfer any brackets, clips, or attached limiter from the original element if required
• Avoid touching the element surface; secure all connections and test both inner and dual settings after reassembly

This replacement heating element restores the heat your appliance needs to cook reliably. Swap in a fresh element to bring back consistent temperatures and dependable performance when the original has failed or become damaged.

• Converts electrical energy into heat for the appliance's cooking system
• Typical symptoms of a failed element: no heat, slow or uneven heating, visible blistering/cracks, or tripping the circuit breaker
• An open (no continuity) element will prevent the affected oven or surface zone from reaching set temperature
• Designed to fit specific models; match by model/part number for proper application

• Disconnect power at the breaker before servicing; elements run on high voltage
• Take a photo and move wires one at a time to the new element; ensure terminals are fully seated
• Handle the element carefully—do not bend, kink, or stress terminals
• Reuse existing mounting screws/brackets as applicable; verify no wires contact metal before restoring power

This is the radiant surface heating element that powers one burner on a glass-ceramic cooktop. Replacing a failed element restores fast, even heat and reliable temperature control for everyday cooking.

• Converts electrical energy into heat for a single cooktop zone
• Works with the burner control to cycle on/off and maintain temperature
• Common symptoms include no heat, intermittent heat, or very slow heating
• Visible hot spots, blisters, or cracks on the element indicate failure

• Disconnect power to the range/cooktop before servicing; high voltage is present
• Allow the glass top to cool; lift or remove it to access the element as your model requires
• Transfer wires one at a time to the new element; secure using existing brackets/mounts
• Ensure the element is centered under the glass and test operation before reassembly

This is the large surface heating unit for an electric range or cooktop. Replacing a failing unit restores consistent stovetop heat so cookware warms predictably and meals cook evenly.

• Provides the heat source for the large burner position on an electric cooktop
• Converts electrical energy into controlled cooking heat
• Replace if the burner won't heat, heats intermittently or unevenly, or shows visible breaks, blistering, or burn spots
• Loose, pitted, or discolored terminals can also indicate the unit is failing

• Disconnect power to the appliance before servicing and allow all components to cool completely
• If your model uses plug-in coils: lift slightly and pull the old unit straight out of the receptacle; align and push the new unit straight in until fully seated
• Inspect the burner receptacle for heat damage before reassembly
• Restore power and test operation on low and high settings

Bake element restores oven heat by producing the radiant heat needed for baking and roasting. Replacing a worn or damaged bake element helps the oven reach and maintain set temperatures for more consistent cooking results. What it does:

• Heats the oven cavity to provide direct radiant heat for baking and roasting.
• Use when the element shows visible breaks, blistering, or does not glow when the oven is set to high.
• Common symptom indicators: oven won't reach set temperature, uneven baking, or longer-than-normal cook times.
• Works as a direct replacement for the oven's lower/bake heating element.

• Disconnect power at the breaker or unplug the appliance before starting any repair.
• Allow the oven to cool completely and wear gloves to avoid sharp edges.
• Match the part to your model and terminal layout before installing; tighten connections securely.

This part is a replacement surface element designed for use with various different models of ranges and electric cooktops.This part supplies the heat to the cooktop and thus is critical for proper appliance functionality. If the current surface element is worn, malfunctioning, or in any way rendered ineffective, it will need to be immediately replaced. Ensure the range is entirely disconnected from the power source before attempting to replace this part. Work gloves should be worn whenever attempting appliance repairs.This is a genuine OEM part made by Frigidaire and has been sourced directly from the manufacturer. This surface element is suitable for use on a variety of range models manufactured by Frigidaire, Electrolux, Gibson, Kelvinator, and some other brands. It is a genuine OEM part and thus is manufactured from high-quality, durable materials. This part is sold individually.

This radiant surface element restores heat to a glass-ceramic cooktop burner. Replace a failed element to bring back even, reliable heating and responsive temperature control for everyday boiling, simmering, and cooking. What it does:

• Provides radiant heat to a designated cooking zone beneath the glass cooktop
• Common symptoms: surface burner won't heat, heats unevenly, or cuts out intermittently
• Visible signs can include burned or cracked element traces or damaged terminals

• 1 radiant surface element

• Disconnect power at the breaker before servicing; allow the cooktop to cool completely
• Lift or remove the glass top to access the element
• Photograph wiring and transfer leads one at a time to the new element to maintain correct connections
• Support the element and brackets during reassembly and avoid touching the element surface with bare hands

Restore reliable top heat for broiling and browning. This replacement broil heating element brings your oven's broil function back to full strength so foods brown evenly and the broiler heats when selected.

• Provides high, direct heat from the top of the oven during the broil cycle
• Helps with top-browning in some baking/roasting modes
• Common failure signs: broiler won't heat or glow, uneven browning, visible breaks or blistering on the element
• Often tests "open" (no continuity) when failed

• Disconnect power at the breaker before servicing; allow the oven to cool completely
• Remove mounting screws, then gently pull the element forward and support the wires
• Label and transfer wires to the new element one at a time; do not allow wires to slip back into the rear cavity
• Reinstall screws, ensure secure connections, restore power, and test the broil function