Frigidaire Wall Oven Parts

The Handle is an OEM replacement part for Frigidaire ranges. It is the component located on the front of the oven that allows for opening and closing the oven door.

Causes of a bad handle stem primarily from wear and tear due to frequent use over many years. Exposure to heat cycling may also degrade adhesives or secondary components that secure the handle.

Symptoms of a faulty handle include:

• Difficulty opening or closing the oven door
• The handle detaching from the door
• Sharp edges or broken pieces that compromise safety
• Loss of grip or stability while moving the door

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Spark Module is an OEM part for Frigidaire gas ranges. It allows precise flame control for cooking. This module sends the necessary electrical currents to the igniters at each burner, which then spark to ignite the gas. 

Causes of a bad spark module can include electrical failures, corrosion, or moisture damage, as well as wear and tear from normal use. 

Symptoms of a bad Spark Module include:

• Burners failing to ignite despite being turned on
• Intermittent ignition or weak spark generation
• Continuous clicking sounds from the burner area even after ignition
• Unlit burners leading to gas smell, indicating incomplete combustion

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Burner Knob is an OEM part for Frigidaire ranges. It is designed to control the burner settings on your range, allowing you to adjust the flame intensity for precise cooking. The knob is easy to grip and turn, providing a user-friendly interface for managing your cooking tasks.

Over time, burner knobs can become damaged due to frequent use, exposure to heat, or accidental impact. These issues can lead to a malfunctioning knob that affects your ability to control the burners accurately.

Symptoms of a bad Burner Knob include:

• Difficulty turning the knob
• The knob not staying in place
• Incorrect flame intensity settings
• The knob becoming loose or falling off

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This surface element control board manages a dual radiant cooktop burner. It regulates power to the inner and outer coils so the element heats correctly, changes size as selected, and responds accurately to temperature settings.

• Controls power to a dual radiant surface element
• Directs inner/outer ring operation based on size selection
• Modulates heat output to match the set level
• Common failure symptoms: dual burner won't heat, only one ring heats, stuck on high, or erratic cycling

• Disconnect power at the breaker before servicing to avoid electrical shock
• Access is typically under the cooktop or rear top panel; refer to your model's service information
• Move wire connectors one at a time to the new board to maintain correct placement
• Handle the board by the edges and observe ESD precautions

The Overlay is an OEM part for Frigidaire ranges. It protects and covers the control board and features clear markings for settings and controls. This overlay ensures that users can easily read and operate the appliance, maintaining the aesthetic integrity of the kitchen unit while safeguarding the electronic components beneath from dust, splashes, and accidental touches.

Causes of a bad overlay can include peeling, fading of markings, cracks, or bubbling, often resulting from high heat exposure, frequent cleaning, or general wear and tear over time.

Symptoms of a bad Overlay include:

• Difficulty in reading control settings
• Unattractive appearance due to visual wear
• Misinterpretation of controls, leading to incorrect appliance use

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Spark Module is an OEM part for Frigidaire cooktops and ranges. It is responsible for generating the electrical spark that ignites the gas burners. This module sends a high-voltage signal to the igniters, ensuring the burners light up quickly and reliably when you turn the knobs.

Causes of a bad spark module can include electrical surges, wear and tear from regular use, or exposure to moisture, which can lead to corrosion or short-circuits. 

Symptoms of a bad spark module include:

• Burners not igniting
• Weak or intermittent spark
• Clicking sound without ignition
• Some burners working while others do not

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Overlay is an OEM replacement part for Frigidaire ranges. Its primary function is to cover and label the selection buttons on the control board, thus facilitating easier identification and use. This part does not include any additional components, as it is just the overlay.

Causes of failure relate to repeated exposure to heat and moisture around the range diminishing overlay adhesives over time. Burns or punctures are also possible from cooking mishaps.

Symptoms include:

• Detached or peeling sections exposing internal components
• Discoloration, melting or warping of printed graphics

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

The Leveling Leg Assembly is an OEM part for Frigidaire ranges. This part provides stability by allowing users to adjust the height of the range, ensuring it is level and balanced on the floor.  

Causes of a bad leveling leg assembly can include wear from frequent adjustments, damage due to heavy loads, or breakage from accidental impacts.  

Symptoms of a bad leveling leg assembly include:

• The range being uneven or wobbling
• Difficulty in leveling the range using the legs
• Noise or movement when the range is in use
• Doors not aligning properly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Radiant Surface Element is an OEM part for Frigidaire ranges and cooktops. This part generates heat for cooking and boiling on the cooktop surface.

Causes of a bad Radiant Surface Element can range from electrical issues or loose connections to physical damage from impact or spillovers.  

Symptoms of a faulty Radiant Surface Element include:

• Element not heating up or providing insufficient heat
• Element glowing unevenly or only partially heating
• Cracks or damage visible on the element surface
• Burning smells or discoloration on the cooktop

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This valve controls gas flow to a range/cooktop surface burner for smooth ignition and precise flame adjustment. Replacing a worn valve helps restore reliable burner lighting, accurate heat control, and safer shutoff.

• Regulates gas to a surface burner for ignition and flame size control
• Sticking or worn internal seals can cause hard-to-turn operation or gas odor
• Failure may prevent the burner from lighting or shutting off completely
• Inconsistent or unresponsive flame adjustment can indicate a failing valve

• Disconnect power and shut off the gas supply before servicing
• Allow the appliance to cool; access the valve/manifold per your model's instructions
• Mark and disconnect tubing and any wires; transfer fittings or a separate spark switch from the old valve if applicable
• After installation, restore gas and check all joints with an approved leak-detection solution; verify proper burner operation

The Rack is an OEM replacement part for Frigidaire wall ovens. It is designed to provide a stable and secure surface for placing cookware and bakeware inside the oven.

Causes of a bad rack can include warping or bending from exposure to high oven heat over extended use. Heavy pots or pans dragged across rack surfaces may puncture or dent racks over time.

Symptoms of a bad rack include:

• Difficulty smoothly sliding racks in or removing them from the oven
• Sagging or unstable surfaces that may compromise food placement
• Rust or corrosion on the rack

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models

This ignitor/orifice assembly combines the surface burner spark electrode with the orifice holder that meters gas to the burner. Replacing a worn assembly restores reliable ignition and proper gas flow for steady, even flame performance.

• Provides the spark to ignite surface-burner gas
• Houses the orifice that controls gas flow into the burner head
• Helps resolve burners that won't light or only light with a match
• Can improve weak, uneven, or delayed ignition
• Replaces cracked or carbon-tracked electrodes and corroded orifice holders

• Disconnect power and shut off the gas supply before servicing
• Let the cooktop cool; remove grates, caps, and burner heads to access the assembly
• Disconnect the spark lead and gas connection, install the new assembly, and secure fittings per OEM guidance
• After reassembly, restore gas and check connections for leaks with an approved leak-detection solution; verify ignition and flame

The Knob is an OEM part for Frigidaire ranges and ovens. It is used to control the temperature and settings for the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.

You should replace this knob if it becomes damaged or worn out. Common causes of a bad knob include physical damage from impact, wear and tear from frequent use, or melting due to exposure to high temperatures.

Symptoms of a bad knob include:

• Difficulty turning the knob
• Knob slipping or not staying in place
• Cracks or breaks in the knob
• Inaccurate temperature or setting adjustments

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This part is a replacement control kit. It is made to replace a broken or ineffective part in some models of ovens and ranges.In order to monitor the temperature and control the oven settings, the control kit needs to be in proper working order. In cases where this part is warped, corroded, worn, broken, or in any way ineffective, the control kit will need to be immediately replaced. Prior to undergoing repairs, it's critical that the oven is entirely disconnected from the power source. Always wear work gloves when attempting an appliance repair.This is a genuine OEM part that has been manufactured by Frigidaire and has been sourced directly from the manufacturer to ensure high quality. This control kit can be used with various different models of ovens and ranges that have been manufactured by brands that include Frigidaire, Electrolux, Gibson, Westinghouse, and others. This is a genuine OEM part and thus is made of high-quality, durable materials and is sold individually.

The Top Burner is an OEM part for Frigidaire ranges. This burner is designed to provide a reliable flame for cooking on the stovetop. It ensures consistent heating and efficient cooking performance, fitting seamlessly into the design of your range.

Common causes of a bad burner include clogging from food spills, corrosion due to exposure to moisture, or physical damage from heavy cookware.

Symptoms of a bad top burner include:

• Uneven heating or inconsistent flame
• The burner not igniting properly
• Visible damage or corrosion on the burner
• A weak or flickering flame

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This bake element is the primary heat source for the bake cycle in your range or wall oven. Replacing a failed element helps restore proper preheating and more even results when using the bake setting.

• Provides direct heat during the bake cycle
• Works with the control/thermostat to reach and maintain set temperature
• Common failure symptoms: no heat in bake, very long preheat, won't reach temperature, uneven baking
• Visual clues: blistering, cracking, breaks, or burnt spots on the element sheath

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the element from the oven cavity; remove mounting screws/bracket
• Pull the element forward carefully and move wires one at a time to the new element; do not let wires slip back into the insulation
• Ensure terminals are fully seated and the mounting plate is secure before restoring power