Frigidaire Wall Oven Parts

The Switch Rocker is an OEM part for Frigidaire ranges. This switch is used to control various functions of the range, such as turning on heating elements or activating specific cooking modes. It provides a reliable and straightforward interface for managing the range's features.

You should replace the range switch rocker if it becomes faulty. Causes of a bad switch rocker can include wear and tear from frequent use, exposure to high temperatures, electrical malfunctions, or physical damage from impacts or mishandling. A defective switch rocker can result in unresponsive controls, making it challenging to operate the range effectively.

Symptoms of a bad Range Switch Rocker include:

• The switch not responding when pressed
• Inconsistent or flickering performance of the heating elements
• Physical damage or looseness in the switch
• Intermittent operation or complete failure to activate the desired function

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Microwave won't start or light stays on when door closes? A faulty door latch prevents proper switch engagement. DIY repair typically takes 15-20 minutes.

This replacement radiant surface element restores consistent burner heating under the glass cooktop on compatible electric ranges. It helps your cooking zone reach and maintain temperature so pots and pans heat evenly.

• Converts electrical energy into radiant heat beneath the glass surface
• Maintains set temperature by cycling on and off during operation
• Common symptoms: burner won't heat, heats weakly or unevenly, or only part of the ring glows
• May show visible scorching or breaks when inspected after access

• Disconnect power at the breaker before servicing and allow the cooktop to cool completely
• Lift/prop the glass top or remove the burner pan as your model requires to access the element
• Label and transfer wires one at a time; ensure all terminals are firmly seated
• Handle the element carefully to avoid bending or stressing the coil and supports

Microwave door won't open when you press the button? This door release lever connects the button to the latch mechanism. DIY fix in 30 minutes.

This electric heating element restores consistent, reliable heat in your appliance, so cooking or warming functions work as intended. Replace a failed element to eliminate slow heat-up, uneven temperatures, or no-heat conditions.

• Converts electrical power into heat for the appliance's designated cavity or surface
• Common failure symptoms: no heat, uneven heating, very slow preheat/warm-up
• Visual clues: breaks, blisters, or hot spots on the coil
• May cause the unit to cycle erratically or trip a breaker if shorted

• Disconnect power at the breaker or unplug before servicing; allow all components to cool
• Wear cut-resistant gloves; avoid bending or kinking the element
• Photograph wiring and transfer connectors one-for-one; ensure tight, clean terminal fits
• Inspect wires/terminals for heat damage and replace any compromised connectors

Replace your range oven door gasket to prevent heat escape and maintain proper temperature. Snaps into place with embedded clips. Confirm fit by model.

Protective overlay cover for range control panel. Replace if cracked, scratched, worn, or labels are fading. Installs over the control board buttons.

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Burner not heating or stuck on? This surface element switch controls power to individual cooking elements. Moderate DIY repair requires lifting cooktop.

Burner cap sits on top of the gas burner assembly to distribute flame evenly. Replace if cracked, chipped, discolored, or missing for proper cooking.

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

Fix F90 errors, unresponsive controls, or oven temperature issues with this electric range control board. Manages cooking modes and timer functions.

Oven not heating or broil element staying on constantly? The relay control board regulates temperature by receiving signals from the main control board.

Fix unresponsive buttons and display lights on your electric range with this control board. Controls oven and cooktop functions. 15-minute DIY repair.

Dishwasher door seal prevents leaks by creating a watertight barrier around the door. Replace if you notice water pooling or leaking. Verify fit with your model.