Frigidaire Wall Oven Parts

Small crown-style burner cap for gas cooktops. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or missing.

This electric heating element restores consistent, reliable heat in your appliance, so cooking or warming functions work as intended. Replace a failed element to eliminate slow heat-up, uneven temperatures, or no-heat conditions.

• Converts electrical power into heat for the appliance's designated cavity or surface
• Common failure symptoms: no heat, uneven heating, very slow preheat/warm-up
• Visual clues: breaks, blisters, or hot spots on the coil
• May cause the unit to cycle erratically or trip a breaker if shorted

• Disconnect power at the breaker or unplug before servicing; allow all components to cool
• Wear cut-resistant gloves; avoid bending or kinking the element
• Photograph wiring and transfer connectors one-for-one; ensure tight, clean terminal fits
• Inspect wires/terminals for heat damage and replace any compromised connectors

Fix F90 errors, unresponsive controls, or oven temperature issues with this electric range control board. Manages cooking modes and timer functions.

Fix F10 error codes, blank displays, or temperature fluctuations. This oven control board restores bake/broil cycles and keypad response in your range.

This is an oven bake igniter that mounts inside the oven compartment near the bake burner. It draws electrical current to heat up and open the gas valve, allowing the bake burner to light. Replace this part if your oven takes a long time to heat up, doesn't reach the set temperature, or fails to ignite at all.

The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt

Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.

Symptoms of a bad Surface Element include:

• Not heating up, indicating it may be burnt out or disconnected.
• Heating irregularly or only partially, suggesting there might be damage to the element.
• Taking longer than usual to heat up, which could point to electrical issues or reduced efficiency due to wear and tear.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Range clock display blank or buttons not responding? This control board regulates oven temperature, burners, and display. Common fix for F10 error codes.

Broiler not heating or element burned out? Replace this top broil element to restore radiant heat. Easy DIY fix with basic tools in 30 minutes or less.

Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.

This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.

• Routes gas from the valve through the orifice to the burner head
• Positions the ignitor for reliable sparking and quick ignition
• Helps maintain correct flame size and pattern on that burner
• Common symptoms: burner won't light, clicks without flame, delayed ignition, weak or uneven flame

• Disconnect power and shut off the gas supply before servicing
• Remove grates, caps, and burner heads; lift the cooktop to access the assemblies
• Note wire routing and original orifice location; transfer any reusable hardware from the old part
• After installation, restore gas and check connections for leaks, then test spark and flame

The Knob is an OEM part for Frigidaire ranges and ovens. It is used to control the temperature and settings for the stove's burners or oven functions, providing an interface for selecting heat levels and cooking modes.

You should replace this knob if it becomes damaged or worn out. Common causes of a bad knob include physical damage from impact, wear and tear from frequent use, or melting due to exposure to high temperatures.

Symptoms of a bad knob include:

• Difficulty turning the knob
• Knob slipping or not staying in place
• Cracks or breaks in the knob
• Inaccurate temperature or setting adjustments

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Microwave won't start or light stays on when door closes? A faulty door latch prevents proper switch engagement. DIY repair typically takes 15-20 minutes.

Replace your broken, cracked, or missing gas range burner control knob. This knob mounts on the control panel to adjust flame settings. Easy DIY fix.

Replaces the burner igniter electrode and orifice holder assembly on gas range cooktops. Needed when the original is cracked, corroded, or broken.

Transparent glass panel for your range oven door. Replace when cracked, broken, or clouded to restore clear viewing and proper heat insulation.

 The Dual Element Surface Switch is an OEM part for Frigidaire electric ranges and cooktops. It governs power distribution to the dual element.

Causes may be loose electrical terminals within the switch, defects from past power surges, or general wear over extended use.

Symptoms of a bad surface switch include:

• Inability to toggle one or both elements independently
• Elements activating intermittently or staying stuck on
• Overheating, sparks or strange sounds from faulty connections
• Repeated burning or singeing of cookware bottoms

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.