Frigidaire Washer Parts

This door switch senses whether the appliance door is closed and signals the controls to run only when it's safe. Replacing a worn or intermittent switch restores dependable starts and proper shutoff when the door opens. What it does:

• Detects door position and allows operation only when the door is fully closed
• Interrupts operation when the door opens for safety
• Common symptoms include: won't start, stops when the door is moved, or "door open" message/error
• Intermittent starts due to worn actuator or internal switch contacts

• 1 door switch

• Disconnect power before servicing
• Access the switch from the front or top panel; release mounting screws or tabs
• Move wires to the new switch one at a time to maintain correct positions, then secure the switch
• Test operation before reassembly

The Lid Lock Switch is an OEM part for Frigidaire washing machines. This switch is responsible for ensuring the lid is securely locked during the wash and spin cycles, preventing the lid from being opened and ensuring safe operation of the machine.

Causes of a bad lid lock switch can include electrical failures, wear and tear from frequent use, or damage due to impact or mishandling.  

Symptoms of a bad lid lock switch include:

• The washing machine not starting or stopping mid-cycle
• The lid not locking or unlocking as expected
• Error codes related to the lid lock mechanism
• Unusual noises during the wash or spin cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This door strike mounts on the appliance door and engages the latch/lock to keep the door securely closed so the cycle can start. Replace a worn or broken strike to restore reliable door closure and operation.

• Engages the door latch/lock assembly to secure the door during use
• Enables the control to recognize a closed door so the unit can run
• Wear or damage can cause a door that won't close, "door open" errors, or a unit that won't start
• Commonly damaged by slamming or misalignment; restores proper latching

• Disconnect power before servicing; also shut off the gas supply if working on a gas dryer
• Open the door, remove fasteners, and note the original strike orientation
• Install the new strike and tighten screws without overtightening
• Close the door to confirm a positive latch; adjust hinge/latch alignment if needed

The Door Boot Kit is an OEM part for Frigidaire washing machines. Also known as the door gasket or door seal, is located around the opening of the washing machine. It prevents water from leaking out during the wash cycle and maintains a secure seal when the door is closed.

Causes of a faulty door boot can include regular wear and tear, physical damage, or mold and mildew buildup. These factors can result in issues such as water leakage from the door, visible tears or cracks in the boot, or unpleasant odors from mold growth.

Symptoms of a bad door boot may include:

• Water leaking from the door during the wash cycle
• Visible tears, cracks, or deformations on the boot
• Foul odors emanating from the washing machine

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Leveling Leg is an OEM part for Frigidaire washers. It is designed to provide stability and level the appliance properly on the floor during installation and operation.

Common causes for needing to replace the leveling leg include damage or wear over time, which can lead to unevenness and excessive vibration during wash cycles.

Symptoms that may indicate the need for a replacement leveling leg:

• Uneven or unstable washing machine
• Excessive shaking or vibration during spin cycles
• Difficulty in leveling the washer during installation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Frame is an OEM part for Frigidaire washing machines. This part provides support and structure for the inner door components, ensuring a secure and tight seal during washing cycles to prevent leaks and maintain efficient operation.

Causes of a bad inner door frame can include wear and tear from regular use, physical damage from accidental impacts, or warping from exposure to high temperatures or moisture. 

Symptoms of a bad washer inner door frame include:

• Leaking water during wash cycles
• Difficulty closing or latching the door
• Visible cracks or warping on the frame
• Unusual noises during operation

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Suspension Rod is an OEM part for Frigidaire top load washers. This rod is designed to support the washer tub, helping to absorb vibrations and maintain stability during the washing and spinning cycles.  

Causes of a bad suspension rod can include wear and tear over time, heavy or unbalanced loads that strain the rod, or physical damage from impacts or mishandling.

Symptoms of a bad suspension rod include:

• Excessive shaking or vibrating during the wash cycle
• The washer moving or "walking" during operation
• Unusual banging or knocking noises
• The washer tub being off-center or not balanced

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Suspension is an OEM part for Frigidaire washing machines. It absorbs shocks and reduces vibration during the spin cycle. The suspension system minimizes noise and prevents the washer from walking or moving excessively during operation.  

Causes of worn suspension parts are typically due to normal wear and tear over time under heavy loads or unbalanced loads. 

Symptoms of a bad suspension include:

• Loud banging or knocking noises during spin cycles
• Excessive shaking or vibration
• The washer inching or walking across the floor
• Damage or cracks in the internal suspension components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Capacitor is an OEM part for Frigidaire washing machines. This part stores and releases electrical energy to start and maintain the operation of the washer's motor, ensuring it runs smoothly during wash and spin cycles.

Causes of a bad capacitor can include electrical surges, general wear and tear over time, or exposure to high temperatures and moisture.  

Symptoms of a bad capacitor include:

• The washer not starting or having difficulty starting
• The motor running intermittently or not running at all
• Unusual humming or buzzing noises from the washer
• The washer stopping mid-cycle or not completing cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

The Sump Hose is an OEM part for Frigidaire washing machines. This hose carries water from the tub to the pump, ensuring proper drainage during the wash and spin cycles.  

Causes of a bad sump hose can include regular wear and tear, cracks or holes from aging, and clogs from debris buildup. 

Symptoms of a bad sump hose include:

• Water leaking from the bottom of the washing machine
• Slow or incomplete drainage
• Visible cracks or holes in the hose
• The washing machine stopping mid-cycle due to drainage issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Cover is an OEM part for Frigidaire washing machines. This cover marks the location and type of detergent, bleach, or fabric softener to be used, ensuring proper distribution during the wash cycle. It provides clear guidance for correct detergent placement, contributing to optimal washing performance.

Causes of a bad cover can include wear and tear over time, damage from harsh cleaning agents, or physical impact resulting in cracks or faded markings.

Symptoms of a bad dispenser drawer compartment cover include:

• Faded or illegible markings
• Detergent not dispensing correctly
• Leaks or spills around the dispenser area
• Visible cracks or damage to the cover

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks

Color: white. Measures about 1-1/2 inches in diameter.

This inner door frame forms the interior half of the appliance door. It holds the window and mounting points so the door aligns and latches correctly, replacing cracked or warped plastic that can affect closing performance.

• Forms the interior structure of the door and supports the window
• Provides mounting locations for hinge, strike/catch, screws, and trim
• Helps maintain proper door alignment and seal contact when closed
• Damage can cause misalignment, difficulty latching, rattling/loose window, or a door that won't stay shut

• Disconnect power; if servicing a washer, also turn off the water supply
• Remove the door, place it on a padded surface, and transfer the window and any door hardware to the new frame
• Reuse existing fasteners; tighten evenly and avoid overtightening into plastic
• Verify the door closes and latches smoothly before returning the appliance to service

The Drive Motor is an OEM part for Frigidaire washing machines. This motor powers the drum's rotation during both the wash and spin cycles. It ensures that the drum agitates and spins correctly, allowing for effective cleaning and rinsing of laundry.

Over time, the drive motor can fail due to regular wear and tear, electrical issues, or overloading the washing machine.  

Symptoms of a bad drive motor include:

• The drum not spinning or agitating
• Unusual noises or humming sounds during operation
• The washing machine stopping mid-cycle
• Burning smells coming from the motor area

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.