Frigidaire Washer Parts

The Frigidaire Touch-Up Paint is white in color in a .6 fl oz bottle. For almond order 5303321320. For black order 5303321321.

The Touch Up Paint is an OEM part for Frigidaire appliances. Whether you're dealing with scratches, chips, or other minor cosmetic damage, this touch-up paint provides an easy and effective solution for maintaining the appearance of your appliance. It's designed to adhere well to metal surfaces, offering durability and resistance to further wear and tear.

Over time, appliances can accumulate minor surface damage from regular use, cleaning, and accidental impacts. Using the Touch Up Paint not only improves the aesthetic appeal of your appliance but also helps protect exposed areas from rust and corrosion, which can extend the life of the appliance.

Symptoms of needing Touch Up Paint include:

• Visible scratches or chips on the appliance's surface.
• Areas of rust or corrosion that need to be covered after treating the rust.
• The desire to maintain or improve the appliance's appearance for aesthetic reasons or to maintain its value.

By Frigidaire. 27 inch models, 1990 and up.

The Drive Motor is an OEM part for Frigidaire washing machines. This component is essential for powering the washing machine's drum, enabling it to agitate and spin during the wash and rinse cycles. It ensures that clothes are thoroughly cleaned and properly spun dry.

Common causes of a bad drive motor include wear and tear from frequent use, overheating due to heavy loads, electrical issues such as power surges, and physical damage from impact or mishandling.

Symptoms of a bad drive motor include:

• The washing machine not spinning or agitating
• Loud, unusual noises during operation
• The washer not starting or stopping mid-cycle
• Burning smell or visible signs of motor overheating

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This is a dispenser inlet gasket intended for use on washing machines. This part ensures that the hot and cold water lines do not leak at the point where they are connected to the appliance. If the washing machine is leaking, the gasket may need to be replaced.Replacing a dispenser inlet gasket in a washing machine can be done easily. Screwdrivers and pliers are required. Disconnect the appliance before starting the repair. Wear work gloves for safety. The hot and cold water lines should both be turned off and removed to prevent flooding.This dispenser inlet gasket is an authentic OEM replacement part. It is sourced from the manufacturer. The replacement component is made of high-quality materials. It can be installed in several different models of washing machines. The dispenser inlet gasket is compatible with appliances produced by Frigidaire, Gibson, Electrolux, Westinghouse, and Kelvinator brands.

This replacement washer door window restores a clear view into the tub on compatible front-load models and helps the door seal correctly. Replace a cracked or cloudy pane to reduce leaks and keep operation safe. What it does:

• Provides the transparent viewing window in the washer door
• Works with the door boot/gasket to help form a watertight seal when closed
• Replace if the glass is cracked, chipped, shattered, or excessively scratched/cloudy
• Common symptoms include water leaking from the door area, poor sealing/door won't close, or visible damage to the window

• One door window glass

• Disconnect power and turn off water supply before servicing
• Wear cut-resistant gloves and eye protection; handle broken glass carefully
• Support or remove the door to a flat surface; separate door halves and transfer the window, noting orientation
• Clean the door boot sealing surface; seat the new glass evenly and reassemble without pinching the gasket; test for leaks

This is the water inlet valve that controls the flow of household water into your washer during fill and rinse. Replacing a failing valve restores proper filling performance and helps stop unintended water entry when the machine is idle.

• Opens and closes to allow the correct amount of water into the washer as commanded by the control
• Failure can cause no fill, slow/long fill, or continuous filling/fill when off
• Leaks from the valve body or hose connections indicate the valve should be replaced
• Electrical coil failure may lead to intermittent or no operation

• Disconnect power and shut off the water supply before servicing
• Place a towel or pan to catch residual water; label and disconnect hoses and wiring
• Install the new valve; transfer any brackets or clips from the old part if needed
• Restore water and power, then check all connections for leaks and run a test fill

This triple-solenoid washer water inlet valve regulates and routes hot and cold water into the tub and dispenser as the control commands. Replacing a weak, stuck, or leaking valve restores proper fill, temperature mix, and cycle performance. What it does:

• Opens and closes to allow water into the washer based on cycle and temperature selections
• Three solenoids manage hot/cold mix and direct water to the tub and dispenser compartments
• Typical symptoms: won't fill, slow fill, fills when powered off, incorrect temperature, or leaks from the valve
• May trigger fill-related error codes or cause extended/paused cycles due to fill timeout

• One water inlet valve assembly with three solenoids

• Disconnect power and turn off both hot and cold water supplies before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Label and transfer each wire connector and hose to the matching port on the new valve
• After installation, open supply valves and run a test fill; inspect all connections for leaks

This replacement water inlet valve regulates water flow from the household supply into the washer. It restores proper filling and rinsing when the original valve leaks, sticks, or fails to open.

• Opens and closes to control water entering the dispenser/tub as directed by the control
• Helps maintain correct fill levels and flow during wash and rinse cycles
• Typical symptoms: no fill, slow fill, leaking at the valve, or water continuing to fill when off
• Often required when valve coils test open/short or mineral buildup causes the valve to stick

• Disconnect power and turn off both water supplies before servicing
• Place towels to catch water; relieve line pressure and label hoses/connectors for reassembly
• Transfer any mounting hardware from the old valve if needed; do not overtighten fittings
• Restore water and power, then run a fill cycle and check all connections for leaks

This drain pump assembly actively removes water from the washer tub during drain and spin cycles, helping prevent standing water and cycle interruptions. Replacing a worn pump restores proper draining and reliable cycle completion.

• Pumps water from the tub through the drain hose to the household drain
• Common symptoms: no drain or slow draining, water left in tub, cycle stops due to drainage issues
• May present with unusual pump noises (buzzing/grinding) or leaks at the pump housing
• Restores proper water evacuation to allow cycles to finish

• Unplug the appliance and turn off water supply before servicing
• Expect residual water—use towels or a shallow pan when removing hoses
• Access the pump (front lower or rear panel varies by model); disconnect wiring and hoses, and transfer any brackets/grommets from the old pump if needed
• Clear the drain filter, sump, and hose of debris; then test for leaks after installation

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This trunnion plate secures the washer's inner basket to the drive hub/trunnion, keeping the tub centered and stable during spin. Replace it if the basket feels loose, wobbles, or makes scraping/knocking noises from the hub area. What it does:

• Couples the inner basket to the trunnion/drive hub so the basket spins true
• Helps maintain alignment to reduce vibration and tub-to-basket contact
• Wear can allow play or slippage at the hub connection
• Common symptoms: wobble, scraping/grinding, excessive vibration, poor spin results

• One trunnion plate

• Disconnect power and wear cut-resistant gloves before servicing
• Access typically requires removing the agitator/wash plate and lifting out the inner basket
• Clean and inspect mating surfaces; align the plate correctly and tighten fasteners evenly
• Check related parts for wear and replace if needed

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This tub cover seal fits between the outer tub and the tub cover/splash guard on compatible washers. It keeps wash water and suds contained, helping prevent leaks from the top of the cabinet during agitation and spin.

• Forms a watertight barrier between the outer tub and the tub cover/splash guard
• Helps prevent splash-over and top-rim leaks during wash and spin
• Maintains proper containment of water and suds inside the tub assembly
• Common failure signs: water leaking from the top area, wet streaks down the outer tub, visible cracks, hardening, or flattening of the seal

• Disconnect power and shut off water supply before servicing; wear gloves and eye protection.
• Access the tub cover per service instructions; release the retainer ring/clips to remove the cover and old seal.
• Clean and dry all mating surfaces; remove residue so the new seal seats evenly.
• Lightly moisten the new seal, install uniformly around the rim, reinstall the cover/retainer, and run a short test with water to check for leaks.

This replacement timer is made by Frigidaire and is compatible with commercial washers.This timer controls the internal components that monitor the duration of the cycles. If the user notices that the laundry center cycles are not running for the correct amount of time or do not start at all, the timer may need to be tested for continuity and then replaced. Make sure to entirely disconnect the appliance from the power and water sources and wear work gloves before attempting any repairs or replacements. This is an authentic OEM part made of high-quality, durable, non-corrosive materials and is only sold individually. This timer can be used with washers that have been manufactured by Frigidaire, Kenmore, Electrolux, Gibson, Kelvinator, Westinghouse, and some other brands.

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.