Parts for Electrolux SEQ7000FS0: 05 - Front Panel / Lint Filter Parts

The Dryer Seal is an OEM replacment part for Frigidaire dryers. It is located at the doorway opening where the drum rotates and helps prevent lint, moisture, and heat from escaping. The seal is a crucial component that ensures efficient drying and heat retention within the dryer drum. 

Causes of a bad seal can include wear and tear over time from continuous use or damage due to mishandling. The nylon seal experiences a lot of friction and heat stress with each drying cycle.

Symptoms of a bad seal include: 

• Increased drying time as heat escapes 
• Excess lint and moisture accumulation inside dryer components
• Visibly worn or cracked seal edges
• Cool air leakage noticed around the door when the dryer is running

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

White plastic plug insert that covers unused openings on your dryer. Keeps out dust and debris while restoring a clean finish. Replace if cracked or missing.

Upper felt seal creates a tight barrier between drum and cabinet to prevent clothes from catching in gaps. Replace if fabric snags or grinding noises occur.

Seals the gap between drum and front panel to prevent air leakage and clothes snagging. Replace if worn, torn, or causing thumping noise. Verify fit.

Dryer won't start or stops mid-cycle? A broken door catch prevents secure closure, triggering safety shutoffs. Simple snap-in replacement, 1 minute.

The Door Switch is an OEM part for Frigidaire dryers. This part ensures that the dryer operates safely by only allowing the machine to run when the door is completely closed. Positioned typically at the door frame, the switch activates when the door is shut, signaling the control system that it's safe to begin the cycle.

Over time, door switches can wear out or become damaged, which can interfere with the normal operation of the dryer. 

Symptoms of a faulty Door Switch include:

• The dryer not starting when the door is closed.
• The dryer stopping unexpectedly, which might be due to a loose or faulty switch.
• A lack of the usual "click" sound that indicates the door has latched properly, suggesting the switch isn’t engaging.
• The dryer continuing to run when the door is opened, which poses a significant safety risk.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Captures lint and debris during drying to prevent vent clogs. Replace if damaged, warped, or worn. Confirm fit with your dryer model number.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement door hinge for dryers. Installs on the door opening to enable proper opening and closing. Needed when hinge is cracked, broken, or worn.

Replace your dryer door gasket to restore an airtight seal and prevent heat loss. Installs in minutes—just pull out the old, snap in the new. Confirm fit.

This genuine replacement door gasket seals the refrigerator door to keep cold air in and reduce energy loss. It helps maintain consistent temperatures and prevents drafts and moisture buildup around the door. What it does:

• Creates an airtight seal between the door and cabinet to preserve internal temperature
• Helps prevent frost and condensation by stopping warm, humid air from entering
• Reduces compressor run time by minimizing cold-air leakage
• Commonly replaced when the seal is torn, compressed, warped, or no longer seals fully

• One door gasket

• Clean mating surfaces and remove old gasket adhesive before installing the new gasket
• Gasket may need to be warmed and flexed for proper seating; follow OEM fitting guidance
• Check for even compression around the door; do not overtighten or force the gasket
• Disconnect power or follow safety guidelines per appliance before performing service

Replacement door panel for dryers and laundry centers. Restores exterior appearance when the original panel is cracked, dented, or damaged.

Dryer door won't stay closed? The door strike secures the door latch during operation. Quick DIY fix—installs from the front in minutes.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Plastic door cover

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

Fastens panels, brackets, and internal components in your dryer. Replace stripped, rusted, or missing screws to restore secure mounting and alignment.

Replace your dryer's heater plug insert if it's cracked, broken, or missing. This small component fits into the heater housing to secure connections.

T-plug electrical connector for dryer wiring harnesses. Replaces damaged, corroded, or broken plugs to restore secure connections between components.

Sound dampening pad for dryers. Installs inside the cabinet to reduce vibration and noise. Replace if worn, torn, or missing for quieter operation.

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.