General Electric Dishwasher Dispenser Parts

This cap tower upper is the replacement cover piece for the top of the dispenser/tower assembly. It restores the finished fit and alignment of the tower so the dispenser components sit correctly and look complete. What it does

• Covers and protects the top section of the tower/dispenser assembly to keep internal components shielded.
• Restores the correct appearance and alignment of the dispenser area after damage or wear.
• Helps prevent debris from entering the tower opening and interfering with nearby parts.
• Commonly replaced when cracked, broken, chipped, or missing, or when the tower no longer seats properly.

• One cap tower upper.

• Disconnect power to the appliance before beginning any repair.
• This part typically snaps or fits into the tower; inspect surrounding clips or tabs for damage before installing.
• Handle plastic tabs carefully to avoid further breakage; replace any damaged mounting clips.

Color: blue-gray. It measures about 1-1/2 inches in diameter.

This dishwasher detergent dispenser assembly stores detergent and releases it at the correct time in the wash cycle to ensure consistent cleaning results. Replacing a worn dispenser restores reliable soap release and helps improve wash performance.

• Holds detergent and opens when signaled by the control
• Common symptoms: detergent cup won't open, soap left in the cup after cycle, broken dispenser door/latch

• Disconnect power to the dishwasher before servicing
• Open the door and remove inner-door screws to access the dispenser
• Release locking tabs, remove the old dispenser, and clean the sealing surface
• Seat the new dispenser evenly, reinstall screws, restore power, and run a test cycle

This dishwasher vent cover mounts on the inner door and shields the exhaust opening. It directs moist air out during drying while helping keep spray and debris out of the vent path to protect internal components. What it does:

• Covers the door vent opening and helps guide exhaust airflow during the dry cycle
• Helps keep water spray and debris from entering the vent assembly
• Supports proper moisture management around the top of the door/control area
• Replace if the cover is cracked, warped, loose, or missing, or if steam/water escapes from the vent area

• 1 vent cover

• Disconnect power at the breaker and turn off the water supply; wear cut-resistant gloves
• Access is through the door; on many models the inner door panel must be removed to reach the vent area
• Ensure any gasket/seal is properly seated and secure the cover evenly—do not overtighten
• Run a short cycle and inspect the vent area for leaks

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

• Supports and stabilizes the middle spray arm beneath the upper rack
• Maintains proper clearance for smooth rotation and spray pattern
• Replace if cracked, warped, or worn
• Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

• Disconnect power to the dishwasher before servicing
• Slide out the upper rack; release tabs or fasteners to remove the old bracket
• Transfer the spray arm to the new bracket and snap or secure it in place
• Spin the arm by hand to ensure free rotation before running a cycle

This harness plug connects the dishwasher's wiring to the water inlet valve. Replacing a burnt, brittle, or loose connector restores a solid electrical connection so the valve energizes correctly and the tub fills when the cycle begins.

• Provides a secure, keyed connection between the harness and water inlet valve terminals
• Helps resolve no-fill or intermittent fill caused by heat damage, corrosion, or loose contacts at the connector
• Supports proper valve operation to reduce humming-without-fill complaints
• Useful when replacing a damaged plug during valve or harness service

• Disconnect power at the breaker and shut off water supply before servicing
• Note wire orientation; transfer or splice leads per appliance wiring and connector design
• Seat the plug fully on the valve and ensure tight, insulated connections
• Restore power and run a fill test; check for leaks at the valve and hose connections

This upper dispenser trim—commonly called the top tower—replaces the visible upper cover at the refrigerator dispenser area to restore appearance and proper fit. It protects internal dispenser components and keeps the dispenser edges clean and aligned. What it does

• Covers and protects the upper portion of the dispenser tower and its internal components
• Helps maintain a consistent, finished look at the dispenser opening
• Prevents dirt and moisture from reaching internal dispenser parts
• Can reduce rubbing or misalignment of the dispenser fixture that can cause noise or wear

• One upper dispenser trim (top tower) as shown

• Remove power to the appliance before starting work to avoid electrical hazards
• Typically secures with clips or a few screws—gentle prying with a trim tool may be required
• Inspect adjacent trim and fasteners for wear and replace as needed for a proper fit

This water inlet cover replaces a cracked or missing inlet-valve trim to protect and conceal the appliance's water inlet area. It restores a finished look while keeping hoses and valve components shielded from debris. What it does:

• Covers and protects the water inlet valve and hose connections from dust and impact
• Conceals exposed hoses and wiring for a cleaner rear-cabinet appearance
• Helps prevent snagging or accidental contact with the inlet valve assembly
• Reduces debris buildup around the inlet area that can affect connections

• Disconnect power to the appliance and shut off the water supply before starting.
• Usually fastens with a few screws or clips—have a screwdriver or nut driver ready.
• Align cover over the inlet valve area, then secure with the original fasteners.
• After installation, turn water and power back on and inspect connections for leaks.

This rinse aid cap fits the dishwasher rinse aid dispenser and seals the reservoir to keep liquid in the dispenser until released during the wash cycle. Replacing a cracked or missing cap prevents leaks and improves rinse aid dispensing. What it does:

• Seals the rinse aid reservoir so the dispenser releases product only during the rinse cycle
• Prevents leaks or drips from the dispenser fill opening
• Helps maintain proper rinse aid levels for better drying and spotting control
• Fits the dispenser housing and snaps or screws into place per original design

• One rinse aid dispenser cap

• Turn off and disconnect power to the appliance before servicing
• Remove any remaining rinse aid from the dispenser before replacing the cap
• Install by aligning and seating the cap securely; do not force if it does not fit smoothly