General Electric Dispenser Parts

• Will not dispense detergent

Bought the replacement dispenser from APPros.com (of course). The video shows a front control panel, and our dishwasher has the 'hidden' control panel on the top of the door. So here's the difference: 1) You need to take out all the screws, except the two near the latch at the top. The other video shows only taking out the bottom six screws because the remainder of the screws hold the front control panel. I used a couple paint cans with rags on top to hold the corners of the door when... Read more

This was very simple. Thgey just popped back into place asnd the cap screws in. Read more

First replaced the latch, spring, and lever, but no improvement. Then I saw the lever arm on the other half of the door, which by position had to be the way that the timer interacts with the soap dispenser. After turning off the power to the dishwasher, I removed the switch cover (not obvious how -- a video would help: on the left, I slid the narrow rectangular plastic wire cover a little to one side and gently opened it on its little hinge, which is near the left side of the door, and then... Read more

• Will not dispense detergent

Using your program, I loaded the info re my trusty old dishwasher (not ready to abandon over a cap) and you located the proper cap to replace my old one that has been lost for years. [don't ask how that happened in the first place!] I really didn't think you would have a part for an 18-20 year old dishwasher. After ordering the replacement cap, it arrived within a few days. I was so excited that I could fix this problem myself without calling an expensive repairman! I simply removed the part... Read more

Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more

I did not see the old ones fall out, so I was not sure the exact product placement within the rail, which was frustrating, to say the least. For the next person's benefit....these slide into the MIDDLE of the rail that is attached to both sides of the dishwasher. Not the front, not the back, but the middle! Steps to fix: 1) Order 2 of these Roller Bearing Cage. 2) Order 4 of WD12X10304 (AP4484666) end caps!! Unless you have brand new ones already, you will need them for sure and they are... Read more

Replaced the stripper and fill cup - turns out that the fill cup came with the locking tab broken off. The stripper had a missing paddle, and ice cubes would jam and shut down the ice maker periodically. Let the ice maker warm up after you remove it so the plastic is not so brittle. You have to pry the old stripper out. Make sure the new one locks all across the front. My refrigerator has the ice maker mount toe the side instead of from the hangers in back. I wasn't sure how to remove it,... Read more

Repair parts arrived super fast. Installed the new parts according to the supplied instructions. All went well. It took over 2 hours because the unit had to be removed after the water and power were disconnected and then the initial problem diagnosed (motor brushes worn beyond service limits). The removal of the spray bar tower assembly was a challenge until it was discovered that the tower unscrews in a CW direction from the bar that then allowed access to the attachment screw that holds that... Read more

This part came next day. super fast. open door . remove screws on inside facing edge of door. this seperates door front and back halves. unplug electric from dispenser then remove 6 screws holding it to the inside of door. remove dispenser and install new one in reverse order. took 20 to 30 minutes on a small economy size GE dishwasher Read more

Ordered a new detergent dispenser. Worked like a charm. Read more

1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve. Parts $220 for Dishwasher Estimated Labor $400.00 Labor $0.00 Parts $100.00 for Pullout Faucet Estimated Labor $175.00 Labor $0.00 Read more

• Will not dispense detergent

The timer was replaced. It took about 35 minutes. The most difficult thing was holding the door down. Read more

Went online to appliance pro, found my model and the ice maker part number. The process was very easily. The order process was also very simple and the part was delivered promptly with installation instructions. Read more

Ordered new parts and put them in! Read more

Viewed you video on Youtube.com and saw how easy it was to change out the triple water valve. Job completed and working like a charm now. Read more