General Electric Dishwasher Panel Parts

This outer door is the replacement exterior panel that restores the oven's appearance and protects internal components from heat and debris. It fits where the original outer door panel is mounted and helps maintain proper oven operation. What it does

• Replaces a damaged or dented outer oven door panel to improve appearance and protection
• Helps contain oven heat and protect internal door components
• Addresses issues like visible door damage, rattling or loose outer panel
• Works with existing inner door, glass, and hardware when compatible

• Disconnect power to the appliance before starting any repair
• Removal typically requires taking off the oven door and separating the outer panel from the door assembly; keep small parts organized
• Handle glass and sharp edges carefully; wear gloves and eye protection

This toe kick assembly replaces the lower front grille that covers and protects the appliance base, restoring a finished look and preventing debris from entering the cabinet area. Durable trim piece designed to clip or screw into place. What it does:

• Covers the appliance toe space to improve appearance and hide components
• Helps keep dust, lint and small objects out of the base cavity
• Restores proper fit where a cracked, broken or missing grille leaves a gap
• Provides a stable mounting surface for kickplate hardware on compatible units

• Disconnect power to the appliance before servicing to reduce shock risk
• Typically attaches with clips or screws—have a screwdriver or nut driver ready
• Align tabs and press or fasten securely; do not force broken clips—replace hardware if needed

This access panel covers the range's control console and protects internal components while allowing service access. It restores a finished appearance and keeps wiring and electronic parts shielded from debris. What it does:

• Covers and secures the control console area to protect switches, wiring and electronic modules
• Provides an access point for technicians to reach console components during repair
• Helps prevent debris and spills from reaching internal electronics
• Commonly replaced when the console cover is cracked, warped, dented or missing

• Disconnect power to the appliance before attempting removal or installation
• Remove console knobs and screws as needed; handle edges carefully to avoid cuts
• Reuse existing mounting hardware unless damaged; verify panel seats flush before restoring power

This toe kick bracket secures the refrigerator's lower front panel for a snug, finished fit and helps keep the base assembly aligned. It restores proper panel support and prevents rubbing or gaps along the cabinet front. What it does

• Anchors the toe kick/panel to the refrigerator cabinet so the lower front stays flush and stable
• Restores proper alignment when the panel is loose, sagging, or vibrating
• Helps reduce noise caused by a loose lower panel
• Designed to match OEM fit and mounting locations for a reliable repair

• One toe kick bracket/support

• Basic hand tools required; access the lower front panel by removing the toe kick or front access panel first
• Keep screws and fasteners from the original assembly; replace only if worn or damaged
• Turn off power to the appliance if service requires removal of electrical panels or working near wiring

This finished outer door panel restores the appliance's exterior appearance and protects internal door components from damage. It replaces a dinged, cracked, or faded outer panel to refresh the look of the appliance. What it does:

• Replaces a damaged or cosmetically worn outer door surface
• Protects inner door components and wiring from impact and dirt
• Restores a uniform, finished exterior appearance
• Helps the door align and close properly when the outer panel is intact

• Disconnect power to the appliance before beginning any repair
• Removal/installation typically requires removing the door from hinges and transferring handle/trim pieces
• Keep all fasteners and brackets; they may be reused unless damaged

This is a stainless-steel outer door panel that restores the appliance's exterior appearance and provides the finished surface for the door assembly. It replaces a damaged, dented, or scratched outer door skin to improve looks and protect internal components. What it does:

• Serves as the outer skin for the refrigerator/freezer door, forming the visible exterior surface.
• Protects inner door components, insulation, and wiring from damage and moisture.
• Restores a flush, uniform appearance when the original panel is dented, scratched, or corroded.
• Compatible with factory mounting points to mate with the existing inner door and trim.

• One stainless-steel outer door panel.

• Handle, trim, insulation, and hardware are only included if explicitly listed.
• Disconnect power and remove stored items from the door area before beginning work to prevent injury or damage.
• Use caution with sharp edges and support the door to avoid dropping or bending the panel during installation.