General Electric Dishwasher Parts

This mounting nut secures the tower heater assembly in the appliance, keeping the heater stable and properly positioned for safe, efficient operation. Replacing a damaged nut restores secure attachment and reduces rattling or loose components. What it does

• Secures the tower heater assembly to the appliance chassis or mounting bracket
• Helps maintain proper heater alignment for reliable heating performance
• Prevents movement that can cause noise, intermittent contacts, or wear on connections
• Used when the original nut is stripped, corroded, or missing

• One tower heater assembly mounting nut

• Disconnect power to the appliance before attempting any repair
• Use appropriate hand tools; avoid over-tightening which can strip threads or damage the heater assembly

Replacement mounting screw for dishwasher internal and external components. Secures panels, brackets, and parts when original is missing, stripped, or damaged.

This silicon controlled rectifier (SCR) is the control device that regulates high-current power to heating and motor circuits, helping restore proper operation when the original SCR fails. A direct-fit replacement part for the listed appliance control. What it does:

• Regulates and switches high-current power to heating elements or motor circuits as commanded by the appliance control board.
• Stops or reduces power flow when the SCR fails, which can cause no-heat or intermittent heating.
• Can cause symptoms such as no heating, intermittent operation, or incorrect cycle heating when faulty.
• Works with the main control to protect and time the appliance's heating cycles.

• SCR control

• Disconnect power before servicing to avoid electrical shock.
• Handle the part and wiring carefully; match terminals and mounting to the original unit.
• Follow the appliance service manual or wiring schematic for correct installation and testing.

Replace a missing, damaged, or worn spring washer in your dishwasher. Provides tension to keep fasteners secure during vibration and movement.

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Replacement finger indexer for dishwasher dishrack. Installs on the right side to secure and guide dish rack movement. Order if broken or missing.

Right-side dishwasher door hinge assembly with mounting screws. Replaces cracked, broken, or worn hinges to restore door support and alignment.

This right switch breakwater helps position and protect the dryer control switch assembly, keeping the switch secure and preventing rubbing or shorting. It restores stable switch alignment for reliable control operation. What it does:

• Holds the right control switch in place to prevent movement and wear
• Protects the switch from contact with adjacent components that can cause sticking or intermittent operation
• Helps stop rattling or vibration-related noise from the control area
• Supports proper button/knob actuation for consistent user input

• One right switch breakwater

• Intended for use in the dryer control area; inspect surrounding parts for related damage
• Disconnect power before servicing to avoid shock or accidental startup
• Use basic hand tools; do not overtighten fasteners to avoid cracking the plastic
• Replace damaged switches or mounting hardware together for best results

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

Covers the gap beneath your dishwasher front. Installs at floor level. Replace if missing, cracked, rusted, or damaged for a complete look.

This replacement multi-purpose glass shelf provides a sturdy, easy-to-clean surface for organizing food and containers in your refrigerator. Restores usable shelving space after a chip, crack, or missing shelf. What it does:

• Supports refrigerated items and helps keep food organized and visible
• Replaces a cracked, chipped, broken, or missing refrigerator shelf
• Fits into existing shelf tracks or ledges to restore proper shelf spacing
• Tempered glass construction resists everyday cold-area wear (handle with care)

• Remove food and containers from the area before installing
• Handle the shelf carefully; wear cut-resistant gloves if replacing a broken shelf
• Slide shelf into the existing tracks/ledges until fully seated; do not force
• If glass is damaged on arrival, stop installation and contact the seller for a replacement

This shelf cup is a small replacement cup that secures a refrigerator door shelf in place, restoring shelf stability and preventing items from slipping or the shelf from sagging. It's a direct-fit replacement designed to match the original mounting. What it does:

• Supports and anchors a door shelf or shelf bin to the refrigerator door
• Keeps the shelf level so stored items don't slide or tip
• Replaces cracked, broken, or worn shelf cups that allow shelf movement
• Restores proper alignment and secure seating of the shelf/bin

• Disconnect power only if you must move or tilt the appliance; otherwise remove items from the door and work with the fridge closed
• Remove the affected shelf/bin and detach the old cup
• Press the new shelf cup into place until it seats fully; re-install the shelf/bin and check for secure fit

Replace your cracked, rusted, or deteriorating dishwasher upper rack. Includes tiered rack shelf and rollers for secure placement of cups and small plates.

This 10-foot drain hose kit connects your dishwasher to the household drainage system with a smaller drain port connection. It allows proper drainage of wash water and prevents backflow into the dishwasher. Replace this part if you notice water backing up into your dishwasher, poor drainage during cycles, or if the existing hose is damaged or too short.