General Electric Dishwasher Parts

This vent flapper is the exterior exhaust flap that opens to let dryer air and lint exit and closes to keep weather, pests and drafts out when the dryer is off. It restores proper airflow at the outside vent hood. What it does:

• Opens with dryer airflow to allow exhaust to escape and closes when idle to block outside air.
• Helps prevent backdrafts, pests and rain from entering the vent system.
• Can restore normal drying performance when a stuck or broken flap was restricting airflow.
• Commonly replaced when the flap is cracked, warped, jammed or does not seal.

• One vent flapper/exterior exhaust flap.

• Disconnect power to the dryer (and gas supply if applicable) and work from the outside hood when possible.
• Remove the exterior vent hood or access cover to inspect and replace the flap; basic hand tools required.
• Check that the flap moves freely after installation and seats against its seal to prevent air leaks.
• Clean or repair the ductwork to avoid repeat failures.

Replacement finger indexer for dishwasher dishrack. Installs on the right side to secure and guide dish rack movement. Order if broken or missing.

Right-side dishwasher door hinge assembly with mounting screws. Replaces cracked, broken, or worn hinges to restore door support and alignment.

This right switch breakwater helps position and protect the dryer control switch assembly, keeping the switch secure and preventing rubbing or shorting. It restores stable switch alignment for reliable control operation. What it does:

• Holds the right control switch in place to prevent movement and wear
• Protects the switch from contact with adjacent components that can cause sticking or intermittent operation
• Helps stop rattling or vibration-related noise from the control area
• Supports proper button/knob actuation for consistent user input

• One right switch breakwater

• Intended for use in the dryer control area; inspect surrounding parts for related damage
• Disconnect power before servicing to avoid shock or accidental startup
• Use basic hand tools; do not overtighten fasteners to avoid cracking the plastic
• Replace damaged switches or mounting hardware together for best results

This switch sensor is a direct-replacement sensing device that detects the position/state of a moving component and sends that signal to the appliance control for reliable operation. It restores correct sensing when the original fails. What it does:

• Detects and reports a component's open/closed or engaged/disengaged position to the control
• Helps the appliance start and change cycles only when the mechanism is in the correct position
• Can resolve symptoms such as no response from the control, intermittent operation, or cycles that won't advance
• Provides a direct electrical/mechanical interface between the moving part and the control system

• One switch sensor

• Disconnect power to the appliance before starting any repair
• Match this part number to the failed sensor before installing
• Handle wiring and connectors carefully; avoid forcing tabs or pins
• Test operation after installation and restore power only when all connections are secure

This is a glass multi-purpose shelf designed to sit inside the dishwasher dishrack, providing an additional flat surface for cups, small bowls, and other lightweight items. It helps maximize loading capacity by creating a second tier within the rack. Replace this shelf if it is cracked, chipped, or broken, which can cause items to fall through or not wash properly.

This shelf cup is a small replacement cup that secures a refrigerator door shelf in place, restoring shelf stability and preventing items from slipping or the shelf from sagging. It's a direct-fit replacement designed to match the original mounting. What it does:

• Supports and anchors a door shelf or shelf bin to the refrigerator door
• Keeps the shelf level so stored items don't slide or tip
• Replaces cracked, broken, or worn shelf cups that allow shelf movement
• Restores proper alignment and secure seating of the shelf/bin

• Disconnect power only if you must move or tilt the appliance; otherwise remove items from the door and work with the fridge closed
• Remove the affected shelf/bin and detach the old cup
• Press the new shelf cup into place until it seats fully; re-install the shelf/bin and check for secure fit

Replace your cracked, rusted, or deteriorating dishwasher upper rack. Includes tiered rack shelf and rollers for secure placement of cups and small plates.

Secures and positions the heating element in your dishwasher. Replace if cracked, bent, or broken to restore proper element alignment and stability.

Secure wire harnesses in your dishwasher with this harness clip. Replace if wires are loose or clip is broken. Verify fit with your model number.

Sump plate that mounts at the bottom of the dishwasher tub assembly. Replace if cracked, warped, or damaged to restore proper structural support.

This lever assembly allows the upper dish rack to be adjusted for height, located on the right side of the dishwasher rack. Replace when the rack won't adjust properly, feels loose, or the lever mechanism is broken or missing.

Secures the spray arm manifold assembly in your dishwasher. Replace if the ring nut is cracked, stripped, or missing to properly mount the manifold.