General Electric Microwave Parts

This replacement blower fan mounts on the blower motor to move air through the appliance's ventilation path and cool internal components. It restores proper airflow to help clear steam/smoke and reduce noise from a cracked or warped wheel. What it does:

• Couples to the blower motor to push/pull air through the exhaust or recirculation ducts
• Helps cool internal parts while venting cooking steam and odors
• Typical failure signs: scraping/rattling noises, reduced or no airflow, poor venting performance, or intermittent overheating shutdown

• 1 blower fan wheel

• Disconnect power at the breaker or unplug before servicing
• If over-the-range or built-in, support the unit and follow manufacturer procedures to access the blower housing
• Match the original wheel orientation and seat fully onto the motor shaft
• Spin by hand to ensure free rotation and clearance; reassemble and test all fan speeds

This Miraclon heater is a direct-replacement heating element assembly that restores proper heat generation in compatible appliances. It provides reliable, OEM-matching heating performance to help your appliance reach and maintain operating temperatures. What it does

• Replaces the appliance's failed internal heater assembly to restore heat production.
• Heats quickly and evenly to support cooking, drying, or defrosting cycles (depending on appliance).
• Common symptom: no heat or weak heat during normal operation.
• Common symptom: appliance runs but items fail to warm or dry as expected.

• Disconnect power and gas before starting any repair.
• Handle the heater carefully; avoid bending or damaging terminals and mounting tabs.
• Follow the appliance service manual for access, mounting, and wiring instructions.

This TCO cavity is a thermal cutoff assembly that helps prevent oven overheating by interrupting power if temperatures get too high. It replaces a failed cutoff to restore proper temperature safety control. What it does:

• Acts as a temperature safety device that opens the circuit when excessive heat is detected
• Helps prevent overheating-related damage or fire risk when operating the oven
• Common symptom: oven or burner stops heating or cycles off unexpectedly
• Common symptom: oven will not maintain set temperature or complete heating cycles

• Disconnect power to the appliance before servicing to avoid electrical shock
• Replace with the exact part number; follow OEM wiring and mounting orientation
• Inspect surrounding wiring and insulation for heat damage; replace if frayed

This metal tray sits inside the oven cavity to support food or cookware during cooking cycles. Replacing a warped, damaged, or missing tray restores a stable surface and helps maintain consistent, reliable cooking performance.

• Provides a flat, durable platform for placing food or cookware
• Seats on the designed supports/locator features inside the cavity for proper fit
• Replace if bent, warped, rusted, or otherwise damaged
• Common symptoms: missing tray, items wobble or sit unevenly, poor fit, visible damage

• Disconnect power and allow the appliance to cool completely before replacing internal accessories
• Remove the old tray and clean the support area; align and seat the new tray per your owner's manual
• Use only in the modes and configurations specified for your model
• Do not force the tray; ensure it is fully and evenly seated before use

This resin canopy is the interior ceiling cover inside the microwave cavity. It shields the stirrer area from grease and splatter to help maintain even heating and protect internal components for safer, more reliable cooking. What it does:

• Covers and protects the stirrer/waveguide opening at the top of the cavity
• Helps promote even microwave energy distribution for consistent cooking
• Shields internal parts from grease, steam, and food debris
• Replace if warped, cracked, burned, discolored, loose, or if you notice arcing/sparking inside the cavity

• 1 resin canopy

• Disconnect power before servicing; microwave components can carry high voltage
• Remove the old canopy by releasing tabs or fasteners from inside the cavity
• Clean the cavity roof and seating surfaces before installation
• Ensure the canopy is fully seated and do not operate the microwave without it installed

This rotating ring assembly sits beneath the microwave glass tray and lets it glide smoothly for even heating. Replacing a worn ring restores stable turntable rotation and helps reduce wobbling or scraping noises during cooking.

• Supports the glass tray and allows it to rotate on low-friction rollers
• Promotes more even heating by enabling consistent turntable motion
• Addresses issues such as a cracked/warped ring or seized/missing rollers
• Typical symptoms include: tray not turning, binding, wobbling, or grinding/clicking sounds

• Disconnect power to the microwave before servicing
• Remove the glass tray, lift out the old ring, and wipe the turntable track
• Position the new ring on the track; reseat the tray on the center coupler and rollers
• Test with a microwave-safe cup of water to ensure smooth rotation; never operate empty

This micro switch is a small electromechanical door/control switch that restores reliable on/off signaling for your appliance. Replacing a failed switch helps restore normal operation and safety interlocks. What it does:

• Opens or closes an electrical circuit when actuated, enabling controls or motors to run
• Commonly used in door and safety interlock applications to prevent operation when open
• Can stop intermittent power or control-response problems caused by a worn switch
• Helps resolve symptoms like appliance not starting, controls not responding, or cycling unexpectedly

• One micro switch

• Disconnect power (unplug appliance or flip the breaker) before servicing
• Observe sharp edges and wear protective gloves; remove access panels as needed
• Verify correct switch orientation and actuator engagement before reassembly
• Test continuity with a multimeter after installation to ensure proper operation

The Tray Motor is an OEM part for GE microwaves. It is the component responsible for smoothly rotating the turntable tray during operation. A functioning tray motor ensures even heat distribution for consistent cooking results. 

Causes of a bad tray motor can include wearing of internal bushings or bearings, defects in the windings, or damage from liquid intrusion over time.

Symptoms of a bad tray motor include: 

• Turntable tray not spinning or rotating unevenly
• "Turntable On" indicator blinking or remaining constantly lit  
• Burnt or cold spots on cooked food items
• Loud grinding or clicking noises coming from inside

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore microwave models. 

The High Voltage Diode is an OEM replacement part for GE microwaves. It converts the high voltage of the microwave's power supply into a lower voltage suitable for the magnetron. It acts as a one-way valve for electrical current, allowing it to flow in one direction while preventing it from flowing back in the opposite direction.

Symptoms of a faulty high voltage diode include:

• No power or complete loss of power to the microwave
• Inconsistent or inadequate heating performance
• Unusual electrical smells during operation

A bad high voltage diode can occur due to electrical malfunctions, power surges, or excessive heat exposure. If you notice issues such as no power, uneven heating, or unusual electrical smells coming from the microwave, it may be time to replace the old or damaged high voltage diode with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This high-voltage diode assembly converts the microwave's high-voltage AC to DC for the magnetron so the oven can heat food. Durable replacement for failed or damaged HV diodes to restore heating performance. What it does

• Converts high-voltage AC to DC for the magnetron to enable proper microwave heating
• Commonly replaced when the oven stops heating or has intermittent heating
• Can fail shorted or open, cause blown high-voltage fuse, or contribute to arcing/noisy operation
• Works with the high-voltage circuit components (magnetron, capacitor, transformer)

• One high-voltage diode assembly

• Disconnect power and allow the appliance to sit before servicing
• The high-voltage capacitor can hold a lethal charge — discharge safely before touching components
• Use insulated tools and follow OEM safety procedures

Color: Bisque

Package of 12

This optional charcoal replacement filter helps reduce lingering food odors and improves interior air freshness in compatible refrigerators. Easy to swap in refrigerators that use an activated carbon air filtration cartridge. What it does:

• Adsorbs and helps reduce common refrigerator odors for a fresher-smelling interior
• Restores air freshness when stale or musty smells develop
• Works with refrigerators equipped with an activated carbon air filter system
• Serves as a direct replacement cartridge when the original filter is worn or saturated

• Remove packaging and slide or snap the new cartridge into the filter housing; secure per the manufacturer's instructions.
• Do not wash or soak the charcoal cartridge—replace when performance declines.
• Dispose of the used filter cartridge according to local regulations.

Replacement thermostat that senses and controls the appliance heating system to restore accurate heating and stable temperature cycles, helping the appliance reach and maintain the set temperature. What it does:

• Senses temperature and signals the heating element or valve to turn on/off to maintain set temperature.
• Commonly linked to symptoms such as failure to reach set temperature, temperature fluctuating or cycling erratically, or continuous heating.
• Works as the temperature-regulation component in the appliance's control pathway to stabilize performance.
• Matches the OEM function for temperature control; use when thermostat diagnostics indicate a failed or inaccurate sensor.

• Disconnect power to the appliance before attempting removal or installation to avoid shock or ignition hazards.
• Handle the sensing element and terminals carefully to avoid damage; ensure secure electrical connections and proper routing of any capillary or sensor lead.
• After installation, test the appliance through a full heat cycle to confirm correct operation.

This microwave high-voltage transformer steps household AC up to the high voltage required by the magnetron to generate microwave energy. Replacing a failed transformer restores heat when the oven runs but food remains cold.

• Steps up line voltage to supply the magnetron during cooking
• Common symptom of failure: microwave runs but does not heat
• May also cause loud humming, a burning odor, or tripped breaker/fuse when energized
• Visual signs can include scorching or discoloration on the windings or terminals

• Disconnect power; the high-voltage capacitor can retain a dangerous charge—discharge it before servicing
• High-voltage microwave repairs are hazardous
• Note wire positions and mounting orientation before removal; transfer any brackets or insulators as configured
• Secure with original hardware and verify all connections are tight and routed clear of heat or moving parts