General Electric Range Switch

This plunger switch is the push-style electrical switch that completes a circuit when an actuator is depressed, restoring reliable on/off signaling. Use it to replace a worn or broken plunger switch that causes intermittent or non-responsive operation. What it does:

• Closes an electrical circuit when the plunger is pushed, sending a signal to the appliance control.
• Commonly used where a door, lever or dispenser actuator must register a position or user input.
• Can correct symptoms like intermittent operation, a dispenser or mechanism that won't activate, or a stuck/unresponsive actuator.
• Acts as a direct mechanical-to-electrical interface—no electronics required.

• Disconnect power (unplug or turn off breaker) before servicing to avoid shock.
• Remove the access panel or housing to reach the switch; note actuator orientation before removal.
• Disconnect terminals or harness, then swap the old switch for the new one; reconnect terminals securely.
• Test the plunger action and appliance function before reinstalling panels.

Burner stuck on high or won't adjust temperature? This infinite switch restores adjustable heat control to your surface burner. 10-minute repair.

Burner won't heat or stay at the right temperature? This range infinite switch controls surface element heat levels. Direct replacement part.

Burner won't spark or ignite? This ignition switch controls the spark module for gas range surface burners. Mounts on the valve assembly behind knobs.

Oven light switch.

Burner won't turn on or heat settings won't change? This control switch sail assembly restores the actuator that engages your range's control switch.

This control switch activates the surface-burner spark ignition when you turn the knob to Lite. Replacing a worn switch restores consistent lighting and can stop unwanted, continuous clicking caused by a stuck switch. What it does:

• Closes the ignition circuit to the spark module to light a surface burner when the knob is turned
• Typical symptoms: no spark from a specific knob, intermittent ignition, or continuous clicking with knobs in the Off position
• Heat, spills, and moisture intrusion can damage the switch over time

• 1 control switch

• Disconnect power and shut off gas; allow the appliance to cool before servicing
• Remove the knob and front/top panel as needed to access the switch on the burner valve
• Transfer wires one at a time to the new switch; mount in the same orientation and secure
• Restore power and gas; test for proper spark at each burner before reassembly

Range burner not heating or stuck on high? This infinite switch controls power flow to surface elements. Direct replacement restores proper heat control.

This rotary switch replaces a worn or failed control selector to restore reliable function selection. It provides a direct, mechanical interface for choosing settings so controls respond properly when the knob is turned. What it does:

• Routes user input from the control knob to the appliance's control circuits
• Restores reliable selection when a knob won't change settings or clicks without engaging
• Stops intermittent or no-response behavior caused by worn switch contacts
• Supports normal operation of the affected control bank or function

• Disconnect power (unplug or switch off breaker) before starting any work
• Label or photograph wiring before removal to ensure correct reconnection
• Access may require removing a control panel or trim; keep fasteners and small parts organized
• After installation, restore power and verify all functions operate as expected

Oven won't start or displays error messages? A faulty door latch switch prevents operation when the door signal fails. Direct replacement restores safety.

This is a black rocker switch used to control a function on compatible ranges/cooktops. Replacing a worn or inoperative switch restores positive on/off control and reliable operation of the connected feature.

• Controls an appliance function (such as a light or igniter circuit) with a single on/off action
• Common failure signs: switch won't stay on, no response when toggled, intermittent operation, or physical damage/discoloration
• Direct-fit replacement designed for the original switch location
• Helps restore safe, predictable control to the appliance

• Disconnect power and, if applicable, shut off gas before servicing
• Access is typically from the control panel; retain orientation of wires and note terminal positions
• Transfer wires one at a time to the new switch to avoid miswiring
• Inspect connectors for heat damage; replace damaged terminals before reassembly

Burner won't change heat settings or stays on one temperature? This infinite switch restores adjustable control to your range's surface elements.

Replace a faulty range igniter switch when burners won't light or spark inconsistently. This switch controls the spark ignition system for gas burners.

Replacement switch harness that connects a cooktop or range surface element switch to the appliance wiring, restoring secure electrical connections so burners heat reliably and reduce intermittent or unsafe operation. What it does:

• Carries power between the surface element (infinite) switch and the cooktop element or terminal block.
• Restores reliable heating when a damaged harness causes intermittent or no heat.
• Replaces frayed, burned, or corroded wiring that can cause arcing, sparking, or a burning smell.
• Keeps connector terminals secure to prevent loose connections and erratic element behavior.

• Disconnect all power (unplug range or shut off circuit breaker) before starting any work.
• Make secure, fully seated connections; avoid pinched or kinked wires and route harness clear of heat sources.