General Electric Wall Oven Latch, Catch, Lock Parts

This oven door latch assembly secures the door during the self-clean cycle and reports lock status to the control. Replace a worn or failed latch to restore safe locking and reliable self-clean operation.

• Locks the oven door during self-clean to prevent opening at high temperatures
• Signals the control when the door is locked or unlocked
• Helps the oven start and complete a self-clean cycle safely
• Typical symptoms: self-clean won't start or finish, door won't lock/unlock, lock motor runs continuously or is noisy, lock indicator stays on

• Disconnect power at the breaker and allow the oven to cool completely before servicing
• Access is typically from the top or behind the control panel; remove panels as required and note linkage/switch orientation
• Transfer any linkages or mounting hardware from the original latch in the same orientation
• Manually cycle the latch to verify smooth operation before restoring power and testing self-clean

This latch and tape assembly restores proper door engagement on compatible ovens/ranges so the door closes and locks as designed. It helps ensure safe operation and consistent temperatures by keeping the door secured during cooking and, on applicable models, self-clean cycles.

• Provides the mechanical catch that engages the door strike
• Helps keep the door closed; supports door-lock function on models equipped with a lock
• A worn or bent latch can cause the door not to close fully or pop open

• Disconnect power; for gas ranges also shut off gas supply
• Access location varies by model; expect to remove panels/trim to reach the latch area
• Transfer/reuse mounting hardware; align latch to ensure smooth door engagement
• After installation, verify door closes and locks properly before restoring power

This oven door latch assembly secures the door and communicates lock status to the control. Replacing a worn or jammed latch restores safe door locking so bake and self-clean cycles can start and finish correctly.

• Locks and unlocks the oven door when engaged or commanded by the control
• Secures the door during the self-clean cycle for safety
• Helps resolve issues such as a door that won't lock or unlock, self-clean that won't start/finish, or a persistent "door locked" indicator
• Wear, binding, or internal failure can prevent proper latching

• Disconnect power at the breaker before servicing
• Access location varies by model; typically serviced from the top, rear, or control/console area—follow your model's service procedures
• Transfer any mounting hardware and reconnect wire harnesses one at a time
• After installation, verify smooth latch movement and door locking before running a cycle

This latch and harness assembly secures the appliance door and sends the closure signal to the control, restoring proper door operation and allowing the unit to start or run normally. What it does:

• Replaces a worn or broken door latch and its wiring harness so the door closes and stays latched.
• Restores the electrical connection that detects door-closed status so the appliance can begin its cycle.
• Commonly used when the door will not latch, the appliance won't start, or the door switch isn't being engaged.
• Fits the original mounting and wiring locations for a direct-replacement installation.

• One latch and harness assembly.

• Disconnect power (unplug or switch off breaker) before starting any repairs.
• Basic hand tools are typically required; handle metal edges and sharp tabs with care.
• Verify correct alignment of the latch and secure all fasteners; test door closure and operation before full reassembly.

This oven door latch is the replacement latch assembly that secures the oven door closed so the appliance can maintain temperature and operate safely. It restores a positive door catch for proper cooking performance and safety. What it does:

• Locks and holds the oven door closed during operation to help maintain oven temperature
• Provides the mechanical catch for the door to engage and stay shut
• Common symptom: door won't stay closed or latch properly
• Common symptom: oven won't complete certain cycles or reach temperature because the door won't latch

• One oven door latch assembly

• Disconnect power to the appliance before beginning work to avoid electrical shock
• Access may require removing the oven door or inner door panel; follow the oven manufacturer's service instructions
• Handle glass and sharp edges carefully and keep screws/fasteners organized

This oven door latch assembly secures the oven door and enables proper latching during oven operation, restoring safe door closure and allowing functions that require a locked door such as self-clean cycles. What it does:

• Replaces a worn or broken door latch so the oven door closes and stays latched
• Allows the oven to detect a closed/latched door for safe operation and self-clean cycles
• Helps stop heat loss from the oven cavity due to a door that won't fully close
• Common symptoms include a door that won't latch, a door that won't stay closed, or an oven that will not start self-clean

• One oven door latch assembly

• Disconnect power to the appliance before starting any repair
• Access may require removing the oven door or inner door panel—follow the oven's service manual
• Handle parts and glass panels carefully; wear gloves and eye protection