General Electric Wall Oven Parts

This back insulation retainer secures the oven's rear insulation in place, keeping insulation from shifting and reducing rattling. It helps maintain proper oven cavity protection and a quieter operation. What it does:

• Holds the rear insulation securely against the oven back panel
• Prevents insulation from sagging or falling into the cavity
• Reduces rattling or vibration caused by loose insulation
• Helps the insulation stay in the correct position for safe operation

• One back insulation retainer

• Disconnect power (unplug or switch off breaker) and allow the appliance to cool before beginning.
• Access typically requires removing the oven's rear panel; keep fasteners organized for reassembly.
• Wear gloves and eye protection when handling insulation and sharp sheet metal edges.

The Oven Door Gasket is an OEM replacement part for GE ranges and wall ovens. It provides a secure seal around the oven door to contain heat within the cooking cavity. The gasket is essential for efficient operation as it helps maintain optimal cooking temperatures.

Causes of a bad door gasket can include heat damage over time, warping from repeated door openings and closings, or accidental tears and ruptures. 

Symptoms of a bad oven door gasket include: 

• Excessive heat loss around the door area 
• Inconsistent or inefficient cooking performance
• The door not sealing properly, allowing heat to escape
• Rust or corrosion on interior door parts

This OEM GE part is compatible with GE, Hotpoint, Monogram, and certain Kenmore wall oven models.

Replacement bake element for the lower oven. It supplies the primary heat during Bake cycles so your range can reach and hold the set temperature, restoring consistent, even baking performance when the original element fails.

• Generates the lower-oven heat during Bake cycles
• Helps the oven reach and maintain the set temperature
• Common symptoms: no heat in Bake, won't reach temperature, uneven baking, or a visibly cracked/blistered element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks, take out the element's mounting screws, and gently pull the element forward to access wires
• Transfer one wire at a time to the new element; prevent wires from slipping back into the oven wall
• Reinstall screws, ensure firm connections, restore power, and test Bake

This replacement control panel and mounting bracket assembly restores a secure, like-new stainless front to the appliance's control area, providing proper support for the user interface components and a clean, factory appearance after dents, cracks, or corrosion. What it does:

• Provides the structural fascia and support for the control area
• Restores proper alignment for buttons/knobs and display openings
• Replaces dented, cracked, or bent panel/bracket components
• Helps eliminate flexing or wobble when using the controls

• One stainless steel control panel and mounting bracket assembly

• Disconnect power at the breaker before servicing
• Wear cut-resistant gloves; sheet metal edges can be sharp
• Transfer existing control components and hardware from the old assembly to the new one
• Photograph fastener locations and wiring before removal; align panel before final tightening

Button board housing that holds the control buttons and secures the control board, restoring stable button alignment and protecting electronics for reliable operation and improved appearance. What it does:

• Secures and positions the button board and PCB so button presses register consistently.
• Protects control electronics from exposure, flexing, or damage caused by a cracked or warped panel.
• Replaces a broken, loose, or cosmetically damaged control panel housing.
• Can help resolve symptoms such as unresponsive, sticking, or intermittently working buttons.

• Disconnect power to the appliance before starting any repair.
• Removal of the control panel and careful handling of ribbon cables/connectors is required; keep track of fasteners and orientation.
• Avoid touching circuit contacts and handle the PCB and flex cables by their edges.

This oven rack is the removable wire shelf that supports pans and dishes inside your oven. Replace a bent, worn, or missing rack to restore safe, level support and proper positioning for consistent baking, roasting, and broiling.

• Provides a stable, level surface for cookware in the oven cavity
• Slides on the side rails to let you set the desired cooking height
• Helps position food at the correct distance from heating elements
• Replace if the old rack is bent, warped, corroded, missing stops, or no longer slides smoothly

What's included: 1 oven rack Installation notes:

• Allow the oven to cool completely; disconnect power or shut off gas before servicing
• Pull the old rack forward to the stops, lift the front edge, and remove
• Insert the new rack with the stop end toward the back; seat it on both side supports
• Verify the rack is level and slides securely before use

Temperature sensor assembly that reads oven temperature and sends signals to the control board for accurate heat regulation, helping restore consistent cooking and dependable preheat performance. What it does:

• Measures the oven's internal temperature and reports readings to the control module.
• Enables correct cycling of the heating elements so the oven stays near the set temperature.
• Common replacement for symptoms like incorrect temperature, long or failed preheat, or uneven baking.
• Works as the oven's temperature-sensing component to help the range maintain consistent results.

• Disconnect power at the breaker before starting any repair.
• Handle the sensor and wiring gently; avoid kinking or damaging the sensing tip or harness.
• Reconnect the electrical connector securely and verify oven operation and temperature accuracy after installation.

This inner oven door glass seal cushions and seals the inner glass pane inside the door, helping contain heat and keep the glass stable and quiet. Replace a cracked or flattened seal to maintain safe, consistent oven performance.

• Seats and cushions the inner door glass panel
• Seals the perimeter of the pane to limit heat and air leaks
• Helps prevent debris and moisture between glass layers
• Can reduce rattling or shifting of the inner glass
• When worn, contribute to longer preheat times or temperature inconsistency

• Disconnect power; for gas ranges, also shut off the gas supply. Allow the oven to cool completely.
• Remove the door and separate the inner panel per your service instructions.
• Note the seal's routing and orientation; install the new seal without stretching or twisting.
• Wear cut-resistant gloves and handle glass carefully during reassembly.

This oven lamp lens is the clear glass cover that protects and focuses the interior lamp, helping keep the bulb safe from food, steam and debris while improving oven interior lighting for safer cooking and better visibility. What it does:

• Protects the oven light bulb from direct contact with spills, splatters and high heat.
• Helps diffuse and direct light for clearer visibility inside the oven cavity.
• Replaces cracked, chipped or missing lens that can rattle or allow debris to hit the bulb.
• Restores proper lamp function when the lens is damaged, reducing glare and hotspots.

• One oven lamp lens (glass).

• Disconnect power and allow the oven and bulb to cool completely before starting.
• Remove mounting screw(s) or lens holder clips, replace lens, and secure hardware snugly—do not overtighten.
• Use appropriate replacement bulb type and handle glass with care to avoid breakage and cuts.

This replacement crystal lamp provides the interior lighting for refrigerators, improving visibility so food and shelves are easier to see. Designed as a direct-fit replacement to restore a clear interior light. What it does:

• Illuminates the refrigerator interior to help you find items more easily.
• Replaces a cracked, broken, dim, or missing lamp assembly.
• Fits into the existing lamp housing and works with the original socket.

• Disconnect power to the appliance before starting any work to avoid electrical shock.
• Handle the lamp carefully—wear gloves or use a cloth to avoid cuts from glass.
• Remove old lamp assembly per the owner's manual; align and seat the new lamp securely in the housing.