General Electric Washer Gasket & Seal

This flood hose gasket seals the joint where the washer's flood/overflow hose connects to the outer tub. A fresh seal helps stop seepage from the tub area, preventing drips or moisture around the top or rear of the washer.

• Creates a watertight seal at the flood/overflow hose connection to the outer tub
• Helps prevent leaks during fill, wash, and spin
• Typical failure signs: drips from the top/back of the tub, visible cracks or deformation, or a loose hose connection

• Disconnect power and turn off water supply before servicing
• Access the flood hose connection at the tub; remove the hose and old gasket
• Seat the new gasket fully and reconnect the hose securely
• Run a short cycle to check for leaks

This inside gasket clamp secures the appliance's inner door gasket, helping maintain a tight seal and reduce leaks. It's a small but important retaining clip used where the gasket meets the door or opening. What it does:

• Holds the inner edge of the door or tub gasket in place to keep the seal seated
• Helps prevent water or air from leaking around the door during operation
• Restores proper gasket alignment when a worn or broken clamp allows the gasket to shift
• Works as a replacement for damaged or missing gasket retaining clamps

• One gasket inside clamp (single clamp as shipped)

• Recommended to inspect the gasket and surrounding trim for wear before installing the clamp
• Remove power and water (if applicable) to the appliance before servicing
• May require basic hand tools and careful prying to remove the old clamp and seat the new one
• If gasket is damaged or torn, replace the gasket as well for a reliable seal

This door gasket seals the refrigerator door to keep cold air in and warm air out, helping maintain proper temperatures and reduce energy use. It replaces a worn, torn, or deformed seal to restore a tight door closure. What it does:

• Creates an airtight seal around the refrigerator door edge to preserve internal temperature.
• Helps prevent frost buildup and condensation by stopping warm, moist air from entering.
• Reduces compressor run time and energy waste caused by a leaking door.
• Restores proper door alignment and magnetic closure when the original gasket is damaged.

• One replacement refrigerator door gasket

• Disconnect power to the appliance before starting any work.
• Clean and dry the door flange thoroughly before fitting the new gasket.
• Start at one corner, press gasket firmly into the channel, and ensure magnetic/retention edges seat evenly around the door.
• If gasket wrinkles or does not seat, warm it slightly or allow time for it to relax; avoid sharp tools that can damage the new seal.

This ring drain hose is the replacement drain tube that routes and removes water from the appliance, restoring proper drainage and preventing leaks or standing water in the wash area. Designed to match the original fit and function. What it does:

• Channels wastewater from the tub/pump to the household drain to maintain normal drain cycles
• Restores proper drainage when the original hose is cracked, kinked, or leaking
• Helps prevent leaks and water damage caused by failed or deteriorated hoses
• Compatible with compatible stock mounting points for a like-for-like replacement

• One ring drain hose (1 piece) as pictured

• Disconnect power and water supply before servicing to avoid shock or flooding
• Inspect adjoining clamps and fittings; replace clamps if corroded or damaged for a secure seal
• Ensure hose routing is free of sharp bends or kinks and is secured per the appliance's service instructions

This gasket nozzle washer is a small rubber seal that fits at a spray/nozzle connection to help prevent leaks and ensure proper water flow. Replacing a worn gasket restores a secure seal and reduces dripping or pooling. What it does:

• Seals the connection at a spray nozzle or outlet to help stop leaks
• Maintains correct water flow through the nozzle for effective spraying
• Commonly replaces hardened, cracked, or flattened gaskets that allow dripping
• Helps eliminate minor water pooling or visible leaks near the nozzle area

• Turn off power and water supply to the appliance before servicing
• Remove the nozzle or fitting per the manufacturer's instructions; replace the old gasket with the new washer, ensuring it seats evenly
• Inspect mating surfaces for debris or damage before reinstalling

This oven door gasket provides a replacement seal that helps keep heat and cooking odors inside the oven for consistent cooking and improved efficiency. It restores a tight seal where the door meets the oven cavity. What it does:

• Replaces a worn, torn, or brittle door gasket to reduce heat loss and hot spots
• Helps the oven reach and maintain set temperatures more consistently
• Minimizes smoke, burning smells, and excess energy use caused by leaks
• Improves cooking performance by restoring a proper seal around the door

• One oven door gasket

• Disconnect power to the range/oven before beginning any repair
• Allow the oven to cool completely; remove the oven door per the manufacturer's instructions if required
• Gasket typically attaches by pushing into a channel around the door or oven frame; use a non-marring tool if needed
• Follow OEM instructions for reinstallation and torque recommendations