General Electric Washer Clip Or Clamp

The Timer Knob Clip is an OEM part for GE washing machines. It secures the timer knob to the timer shaft, allowing users to set and adjust the washing cycle duration accurately.

You should replace the timer knob clip if it becomes worn out, broken, or lost. Common causes of a bad timer knob clip include regular use leading to wear and tear, physical damage from excessive force, or accidental breakage during maintenance or operation.

Symptoms of a bad timer knob clip include:

• The timer knob spinning freely without engaging
• Difficulty in setting or adjusting the timer
• The timer knob falling off or feeling loose
• The washing machine not starting or stopping cycles correctly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Drain Hose Clip is an OEM part for GE washing machines. It secures the drain hose to the back of the washer, preventing it from becoming dislodged during operation. This ensures that water is properly directed out of the washer and into the household drain system, preventing leaks and water damage.

Causes of a bad drain hose clip can include wear and tear from regular use, damage from improper handling during installation or maintenance, or breakage due to repeated stress and movement of the washer.

Symptoms of a bad drain hose clip include:

• Water leaking from the back of the washer
• Drain hose detaching or becoming loose during operation
• Difficulty securing the drain hose in place
• Visible damage or cracking on the clip

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For the entire drain hose, use part number WH41X10096.

The Compression Ring is an OEM part for GE washing machines. This ring is essential for securing the tub within the washing machine, ensuring it remains in place during the wash and spin cycles. It helps maintain the stability and proper function of the washing machine.

You should replace the compression ring if it becomes worn, cracked, or damaged. Causes of a bad compression ring can include frequent use, high-stress loads during wash cycles, or physical damage, which can lead to instability and poor washing performance.

Symptoms of a bad compression ring include:

• Excessive shaking or movement of the washing machine during cycles
• Unusual noises during operation
• The washing machine tub appearing misaligned or loose
• Ineffective washing due to instability

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Outer Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp ensures that the seal is tightly held in place, preventing water from leaking out of the front load washer during operation.  

Causes of a bad Outer Door Boot Seal Clamp can range from corrosion due to exposure to moisture and detergents, to physical damage from improper installation or removal of the door seal.  

Symptoms of a malfunctioning Outer Door Boot Seal Clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or detaching from the front panel
• Visible damage or corrosion on the clamp, compromising its integrity

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The anti-siphon clip secures the washer's drain hose to a standpipe or laundry tub, maintaining the proper air gap to prevent siphoning and backflow. It keeps the hose stable so the washer fills and drains as intended.

• Maintains an air break at the drain to help stop unintended siphoning
• Holds the drain hose securely to a standpipe or sink/tub
• Helps prevent "filling and draining at the same time" or low water levels
• Helps keep the hose from vibrating loose or popping out during cycles

• Unplug the appliance and shut off water before starting
• Route the drain hose per the installation manual; avoid kinks or submerging the hose end
• Snap the clip onto the hose and fasten it to the standpipe or tub edge
• Run a quick test to verify no leaks and correct hose position

The Inner Door Boot Seal Clamp is an OEM part for GE washing machines. This clamp secures the door boot seal, ensuring it stays in place and forms a watertight barrier between the washer door and drum.  

Causes of a bad clamp can include regular wear and tear, corrosion from detergent and water exposure, or physical damage from rough handling. 

Symptoms of a bad inner door boot seal clamp include:

• Water leaking from the front of the washing machine
• The door boot seal coming loose or not staying in place
• The washing machine door not closing properly
• Visible rust or damage on the clamp

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This hose clamp kit secures the washer's hoses at the pump, tub, or valve connections, helping stop leaks and hose blow-offs. Replace worn or missing clamps to restore a tight, reliable seal during fill, wash, and drain.

• Secures drain, pump, and fill hoses to fittings to maintain a watertight seal
• Helps prevent drips, leaks, and hoses slipping off during vibration
• Replaces clamps that are rusted, stripped, deformed, or missing
• Common symptoms: water leaking at hose joints, loose hose connections, clamp won't tighten
• Useful when installing a new hose, pump, or valve

• Unplug the washer and turn off water supplies; have towels or a pan ready for residual water
• Release and remove old clamps; seat the hose fully over the fitting before installing new clamps
• Tighten evenly and do not overtighten to avoid hose or fitting damage
• Restore power and water, then run a short cycle to check for leaks at each connection

This locking clip secures a mating part—often a control knob—onto its shaft on select laundry appliances. Replacing a worn or missing clip restores a tight fit so controls stay in place and operate as intended during use.

• Locks a knob, lever, or similar component onto its shaft/post to prevent it from slipping off
• Maintains a firm fit to reduce wobble and intermittent control engagement
• Replace if the clip is bent, fatigued, corroded, or missing
• Typical symptoms include a knob that falls off, feels loose, or spins without engaging

• Disconnect power to the appliance; turn off water supply for washers
• Pull the affected component straight off to access the clip
• Use needle-nose pliers to remove/install the clip; avoid deforming it
• Ensure the clip is fully seated; test for a snug fit before reassembly

This outer door gasket clamp secures the washer's door boot to the front panel, keeping the seal tight around the door opening to help prevent leaks and keep the gasket seated during operation.

• Holds the outer lip of the door gasket (boot) against the front panel
• Helps maintain a watertight seal at the door opening
• Replace if the clamp is bent, stretched, broken, or missing
• Symptoms include the boot slipping off, water leaking at the front, or a loose gasket

• Disconnect power and wear cut-resistant gloves for safety.
• Open the door, gently pull back the gasket, and remove the old outer clamp.
• Ensure the gasket is fully seated on the front panel lip, then install the new clamp evenly around the opening.
• After installation, run a short cycle and check for leaks around the door.

This clip cover is a small snap-in plastic trim piece that protects and secures appliance panels or trim, giving a finished look and hiding fasteners. Replaces broken or missing covers to restore appearance and retention. What it does:

• Snaps into place to conceal screws or clip anchors on trim and panels
• Helps hold lightweight trim pieces securely to the cabinet or frame
• Prevents exposed fasteners and reduces snagging or sharp edges
• Useful when cracked, worn or lost covers cause loose or rattling trim

• One clip cover

• Disconnect power or unplug the appliance before accessing panels or trim
• Push the clip cover onto the mating clip or anchor until it snaps fully into place
• Use a small flat tool only to remove; avoid prying on surrounding trim to prevent damage
• Replace any damaged mounting clips before installing the cover for a secure fit

A spring-style drain hose clamp that secures flexible drain tubing to fittings to prevent leaks and hose separation. Durable metal construction keeps drain connections tight for reliable wastewater flow and trouble-free operation. What it does:

• Holds drain hose firmly to pump, elbow or spud to reduce leaks and disconnections
• Applies even compressive force around flexible tubing for a secure seal
• Helps stop water spraying or pooling caused by a loose hose connection
• Commonly used on appliance drain and discharge lines where a snug clamp is required

• One spring-style drain hose clamp

• Use pliers to expand the clamp, fit over the hose, then release to engage; avoid twisting the hose while seating
• Replace any cracked or brittle hose before clamping to ensure a leak-free repair
• Disconnect power and water if required by your appliance before accessing the drain connection

This pressure hose clamp secures the small vacuum/pressure hose to its fitting, keeping the hose in place so the appliance can accurately sense water level and cycle pressure. Simple, direct replacement for a worn or loose clamp. What it does:

• Holds the pressure/vacuum hose snugly to prevent leaks or hose detachment
• Helps maintain proper pressure signal for correct cycle and fill operation
• Commonly used when a loose or damaged clamp causes intermittent pressure-related symptoms
• Small replacement part that restores a firm hose connection

• Disconnect power (and water, if applicable) before servicing the appliance
• Use a small screwdriver or pliers to remove the old clamp and secure the new clamp in place
• Ensure the hose is fully seated on the fitting before tightening the clamp

This inlet pipe clamp secures the refrigerator water inlet line to the cabinet or valve, preventing movement and wear. Replaces a worn or broken clamp to help stop chafing and reduce the chance of leaks. What it does:

• Holds the water inlet pipe or tube firmly in place to prevent rubbing and stress at connections
• Helps maintain a steady water line position for proper water/ice dispensing
• Prevents pipe vibration or movement that can lead to leaks or line damage
• Commonly replaced when the original clamp is cracked, loose, or missing

• One inlet pipe clamp

• Turn off water supply and unplug the appliance before starting work
• Access may require removing a small panel or the toe grille depending on model
• Remove the old clamp and snap or fasten the new clamp in the same location; use appropriate fastener if required
• Inspect tubing and connections for damage while replacing the clamp

To use with BOOT #wh8x246