Husqvarna Lawn Mower Parts

Replacement grass catcher bag for walk-behind lawn mowers. Attaches to collect clippings during mowing. Replace if torn, worn, or missing parts.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

Replacement fuel tank for front-engine lawn tractors and riding mowers. Installs to store fuel. Replace if cracked, damaged, or leaking.

Secures the mower blade to the motor shaft. Replace if adapter is worn, stripped, cracked, or no longer holds the blade firmly in place during use.

Blade spindle assembly mounts to the mower deck and houses the shaft where blades attach. Replace if spindle is worn, cracked, or damaged.

Replace a riding mower clutch when blades won't engage or disengage properly. This clutch transfers engine power to the mower deck for cutting control.

Steering shaft connects the steering wheel to the gearbox on riding mowers and lawn tractors. Replace if bent, cracked, or worn for proper steering control.

This part is a clutch that is used on lawn tractors and riding lawnmowers. A clutch transfers the power from the unit's engine to the drivetrain and is responsible for engaging the blade.A new clutch may be needed if the lawn tractor or riding lawn mower will start but then stalls. If the clutch is sticky or if it operates hard, it may be time to replace the clutch. If the engine is revving higher than usual or if there are strange noises coming from the clutch, it is likely that the clutch could be going bad. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This clutch is a genuine Husqvarna part. It is sold individually. This particular clutch is compatible with lawn tractors and riding lawnmowers that are manufactured by Husqvarna and Poulan.

Plastic choke lever for gas line trimmers and edgers. Actuates the choke valve to limit airflow during cold starts. Replace if cracked, broken, or damaged.

Blocks dirt and debris from entering your trimmer engine. Replace when clogged or worn to restore proper airflow and prevent rough running or starting issues.

Flange bearing for riding mower tractors. Replace if you notice vibration or wobbling during operation. Verify fit using your model number.

Protects wheel hub and lug nuts from dirt and grime on riding mowers and tractors. Simple snap-on installation takes minutes with basic tools.

Can't see while mowing at dusk or dawn? This riding mower headlight switch controls your tractor's illumination system. Direct-fit replacement.

This replacement deflector shield is a genuine OEM part intended for use on lawn mowers and tractors. It attaches to the side of the mower and directs grass clippings away from the blade as it mows. This serves to keep grass from bunching up in the blade, which could cause it to stall out. The direction of the deflector shield also blows grass clippings behind the mower to keep any potentially hazardous debris from flying up at the mower. Deflector shields can become dried out and brittle over time and can snap off if the mower drives too close to a wall, tree, or other hard object. Deflector shields usually only need replacing if they break. This would cause grass clippings and debris to fly in all directions, which could be dangerous for the user. Replacing the deflector shield is an easy repair and only requires a socket wrench set. This part is compatible with a wide variety of Husqvarna and Craftsman lawn mowers and tractors and is sourced from the original manufacturer. This product ships individually.

Ground drive v-belt transmits power from engine to wheels on riding mowers. Replace if slipping, worn, or cracked. Verify fit with your model number.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.