Husqvarna Lawn Mower Parts

Can't see while mowing at dusk or dawn? This riding mower headlight switch controls your tractor's illumination system. Direct-fit replacement.

This replacement deflector shield is a genuine OEM part intended for use on lawn mowers and tractors. It attaches to the side of the mower and directs grass clippings away from the blade as it mows. This serves to keep grass from bunching up in the blade, which could cause it to stall out. The direction of the deflector shield also blows grass clippings behind the mower to keep any potentially hazardous debris from flying up at the mower. Deflector shields can become dried out and brittle over time and can snap off if the mower drives too close to a wall, tree, or other hard object. Deflector shields usually only need replacing if they break. This would cause grass clippings and debris to fly in all directions, which could be dangerous for the user. Replacing the deflector shield is an easy repair and only requires a socket wrench set. This part is compatible with a wide variety of Husqvarna and Craftsman lawn mowers and tractors and is sourced from the original manufacturer. This product ships individually.

Ground drive v-belt transmits power from engine to wheels on riding mowers. Replace if slipping, worn, or cracked. Verify fit with your model number.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.

Brake linkage assembly for riding mowers and lawn tractors. Replaces worn, bent, or broken brake linkage brackets. Essential for proper brake operation.

This pinion gear is an essential part of the steering assembly as it translates the rotation of the steering shaft into vertical motion. The pinion gear travels along the drivetrain, which pushes the wheels either forward or backward, causing the mower to turn. Without a functioning pinion gear, the mower will no longer steer. A pinion gear's teeth can slowly wear away through repeated use, causing it to begin slipping. When this happens, the operator will no longer be able to turn their mower as effectively or possibly not at all. This can be dangerous for the operator and they should stop mowing immediately. With most push lawn mowers, the pinion gear is located inside the wheel well. To replace it, simply remove the wheel and mounting washer, pop off the retaining ring, and remove the pinion. Reassemble and test the forward motion of the wheel. This genuine replacement OEM part is compatible with a number of lawn mowers from Poulan, Jonsered, Husqvarna, and Weed Eater. It comes sourced from the original manufacturer and does not include any additional hardware.

This pawl drive is a genuine Husqvarna part, sold individually. This pawl drive can be used as a replacement part in lawn mowers and chainsaws. This pawl drive is made out of durable metal. A pawl drive might have to be replaced within the standard lifespan of a lawn mower or a chainsaw. A pawl drive could suffer damage as a result of general long-term usage or from a direct collision with a falling object or a hard surface; this damage could come in the form of puncturing, erosion to the metal material, or warping the part beyond repair. If this is the case, the pawl drive should be immediately removed and replaced with this genuine OEM replacement part. Remember to wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This Pawl drive is compatible with the following outdoor appliance brands: Husqvarna, Poulan, Craftsman, Weed Eater, and Ariens.

Brake linkage for riding mowers and lawn tractors. Connects between the idler arm and brake arm assembly. Replace if bent, broken, or missing.

Lower drawbar assembly for front-engine lawn tractors. Replaces damaged, bent, or broken drawbar components. Two-piece design mounts to chassis frame.

Replace a cracked, broken, or missing side hood vent grille on your lawn tractor. Installs on the hood to allow proper airflow and ventilation.

This idler arm is a genuine Husqvarna part, sold individually. This idler arm can be used as a replacement part in a lawnmower. This part secures the steering linkage while allowing it free range of motion. If the idler arm is punctured, dented, cracked, chipped, scraped, warped, or eroded, it should be removed and replaced by this genuine OEM replacement part as soon as possible in order to ensure safe continued use.This is a genuine OEM replacement directly from the manufacturer. It is sold individually. This idler arm is compatible with the following outdoor appliance brands: Husqvarna.

This 16.25 inch-long blade is manufactured for use with lawn mowers, lawn tractors, zero-turn mowers, and riding mowers. It is a genuine Husqvarna part. The blade is a crucial component of the mower. It is the part that actually cuts grass. It is normal for the blade to become dull over time. They can be sharpened, but replacing will yield better results.Before replacing the blade on a mower, allow the engine to cool, empty the fuel tank, and disconnect the spark plug for safety. Wear work gloves to protect the hands. Tip the lawnmower onto its handle assembly or side. Use a socket to remove the nuts or bolts that attach the blade to the mower. Replace with the new blade and torque the nuts and bolts.This blade is a genuine OEM part sourced directly from the manufacturer. It is sold individually, and most mowers have only one cutting blade. It is manufactured to be compatible with several models made by Dixon, Husqvarna, and Jonsered.

V-belt pulley for riding mowers with 1.125-inch bore. Replace this drive pulley if the original is cracked, worn, or damaged to restore proper operation.