Ikea Parts

Replaced the water tube that went from the plastic tubing to the ice cube tray. Found that even though it was the same exact length as the original, there was only an extremely small gap from the end of the tube to a splash board. This may have been the root cause of my problems. Read more

Used the vinyl touch up paint on the tops of posts and slid vinyl tips over 130 posts. The paint acts as an adhesive to keep the tips secure. Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more

I ordered the replacement parts, removed broken parts and replaced them with the new parts and all problems resolved. Read more

I looked up why the door was not staying shut. I watched a Youtube video and found it was an easy repair and a few dollars in parts from AppliancePartsPros.com. I had previously bought parts from here, are reasonably priced, and they come in quick. I changed the door parts in 1/2 an hour and it was working great. Saved me from buying a new refrigerator. Go for the express shipping. For my purchase it was a dollar cheaper than standard. Read more

I immediately turned to Appliance Parts Pros and got the best price for 4 new burners and finding parts for my stove top model is a challenge due to its age. My stove top looks new again! Plus, they were delivered ahead of schedule! Thank you!!! Read more

• Won't start

Of course, before disassembling anything, I unplugged and turned off the gas supply. To replace the spark electrode, I removed the drip pan/surface to gain access to the burner assemblies. Next, I unscrewed (with a 1/2" open-end wrench, I think) and disconnected the gas supply tubing from the burner assembly with the cracked electrode, and then unscrewed the assembly itself from the base surface. With the assembly detached, I flipped it over and removed the screw that secured the cracked... Read more

I ordered the burner cap set. Read more

Replaced the water inlet valve. Read more

Simple fix. YouTube was my teacher. Remove 4 screws, replaced failed interface assembly and replaced 4 screws. Second part purchased from Appliance Parts Pros and very satisfied with process. First was a washing machine timer control. Thanks. Read more

I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again. Read more

Looked at web site, but I was not sure I was ordering the correct parts. I did an on line chat . It was great only 3 minutes and I had the parts on the way . Super easy . Needed door hinge. Read more

Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on... Read more

• Door won't open after self cleaning cycle

I knew the door latch was suppose to lock for self clean and it wasn't, so I took the back off and after tracing out wires and the linkage to the door latch, determined that it was a faulty motor on the latch lock. I got on line and Appliance Parts Pros was the first place that I found the part. I was surprised that it wasn't real expensive, but I kept looking for a cheaper price only to come back to order it from APP. I order it around 9:00 on a Thursday night and it was on my front porch... Read more

In an attempt to clean the range from the grease-gunk build-up, I had to remove the burner heads. Unfortunately, the 2 most used burner heads had immovable screws that locked them into the orifices underneath. After numerous hours in attempts to salvage the old burner heads and orifices attempting to remove the immovable screws, I gave up. Checked Maytag's website for parts and found nothing. Turned to AppliancePartsPros.com and found the correct parts for reasonable price in a matter of... Read more