Ikea Range Parts

• Little to no heat when broiling

Removed old element , found the part on exploded view diagram of th oven. Got on appliance parts pro web site put in model number , made sure picture on line looked the same and ordered. While I was at it ordered a bottom pan for the oven that needed replacing. Received both parts 3 or 4 days later regular shipping. Installed both parts no problem . Thanks appliance parts pros. Read more

Replaced the blown heating element. I also only to be on the safe side, replaced the over temp sensor. I checked it with the meter when I pulled it out and it was ok. Tested ok. Thank you very much for the less than 2 day delivery on the part. Read more

First, don't self clean your oven before the holidays. In fact, read up on what damage the self cleaning feature can do to your oven. How did I fix it, I went on line and saw the comments of appliancepartspros.com. I figured out that it was the thermal fuse that probably went wrong since my oven just went lights out after the cleaning. My oven is a Kitchenaid model # KEBS179BSSOO. The part for this model is AP6022801 or WPW10545255. I spoke with technical support but I still had questions. I... Read more

• Little to no heat when broiling
• Element will not heat

Found a real cool Youtube video by AppliancePartsPro.com. I watched it and learned how easy it was to unhook and replace the part with proper care and precautions. It even included tips on critical steps so the wires won't slip back inside the hole and save you from hours of possible mistake. Then I ordered the part. It came the day after, then I replaced the part, meaning, I DID THE WORK! (My wife was so impressed- lol) Easy as pie... but we made and had a much nicer roast the day after.... Read more

Replaced the switches. Read more

I found the gasket on your website. I watched the installation video provided. I purchased the gasket and installed it. It was inexpensive and painless. I will order from you again. Thanks Roger Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Replaced bottom panel Read more

Online chat here said that the oven sensor should be replaced. I got the feeling that was a bit off, so I went with my gut and ordered the thermostat as well. Replaced the sensor and that didn't fix it. Replaced the thermostat and it worked like a charm! Disappointed that they were overconfident in their answer and it would have taken me more days to fix - but, the products came in quickly (basically, next day) and were correct. Online video for my particular oven was incorrect - but it's... Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

Ordered replacement parts Read more

Ordered replacement parts Read more

Ordered the replacement Bake Element and installed it. Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

After doing some research the problem appeared to be the door safety switches. I ordered 3 new ones to replace all the original ones. Some minor disassembly of the microwave front was required to reach the fuse and switches. To reach the switches the control panel wires needed to be unplugged and the panel removed. After doing that replacing the switches was pretty strait forward. As of this comment the microwave has worked for 5 days without blowing the fuse so far. This has probably fixed the... Read more