Need Help?
Call or text
Washer won't agitate or makes clunking noise? This thrust washer reduces friction in the transmission system. Easy DIY repair with video guide.
Pulled the washer apart (using your videos as a refresher) and found that the plastic coupling between the motor and the transmission had failed. Searched for parts vendors and found your site. Ordered the coupling on-line and went back down to clean up the machine. In the cleaning process I found a damaged thrust washer for the upper agitator and broken drive dogs for that same agitator. I went to the website to see if I could augment my initial order. I did not want to pay shipping costs... Read more
Four-rod suspension kit that supports the washer tub and absorbs vibrations. Replace when rods are bent, broken, or when the tub sags or moves excessively.
Replaced suspension rods. Read more
Fix a washer that won't fill, fills slowly, or won't stop filling. This water inlet valve controls water flow during wash cycles. 30-minute repair.
Ordered the valve body from Appliance Parts Pro. It was very easy to find the part on their website. Ordering was simple. The part actually got here the next day. I received an email about 2 hours after I received the part that contained the tracking number. That is what is known as quick and reliable service. Part was a little hard to replace since I have big hands. There are 2 metal screws that hold the valve body to the washer that are in a small confined area. Unless you want to dismantle... Read more
Transmits power from motor to tub for spinning and agitation. Replace if squealing, squeaking, or washer won't spin. Confirm fit with your model number.
Replaced the Gearcase assembly which is a sealed unit that is not serviceable. Also replaced the clutch and belt because they were covered in gearcase oil. Read more
The Capacitor is an OEM part for Whirlpool washing machines. This part helps regulate power supply and voltage levels. It smooths out voltage fluctuations to ensure consistent operation of the motor and internal components. Causes of a bad
Bought one from you and replaced it. I friend did it for the family. Read more
Washer won't start because lid won't lock? This lid latch strike secures the washer lid during operation. Simple DIY fix in under 30 minutes.
Not wanting to spend hundreds of dollars on an appliance technician's service call, I searched online to troubleshoot the problems with my particular Maytag Washer Model Number MVWX500BW0. I stumbled across AppliancePartsPros.com and investigated there the most likely causes for my Maytag Washer's not agitating properly and not spinning at all. In order to acquire some additional information, I telephoned AppliancePartsPros.com and spoke with an extremely professional, knowledgeable and helpful... Read more
Fix a washer that won't fill, fills slowly, or drips when off with a new water inlet valve. Most DIYers complete this repair in 20-30 minutes.
Installed new Water Inlet Valve. Read more
The Idler Arm Spring is an OEM part for Whirlpool dryers, maintains tension in the dryer's belt system. This spring is crucial for the proper operation of the dryer, as it helps to keep the belt tight around the drum and motor pulley, enabling the
Replace the drum drive belt and tension pulley assy. Read more
Secures control knobs to the panel on washers and dryers. Replace if the clip is broken, missing, or worn, causing knobs to fall off or sit loose.
I purchased the lid latch assembly and the lid switch strike. Following the clear video instructions for each part, my handy teenage son was able to remove the lid latch assembly and replace it with the new part as well as the lid switch strike. The washer is back to working perfectly for under $100. Appliance Parts Pros carry the parts to repair and at a lower cost than other online retailers. I saved about $30 compared to the other online site and I saved a service call fee. I'm so glad I... Read more
Seals the agitator cap to prevent water leaks into the agitator assembly. Replace if you notice leaking during wash cycles. Verify fit with your model.
I had previously replaced the pump about 1 year ago. That was not the problem. Still leaked the same way - intermittently, but always in the center of the washer onto the floor. None of the hoses were leaking - no evidence of corrosion or water mineral residue at any of the hose fittings. So, it must have been something else. I studied the parts diagram for the washer tub assembly and concluded the source of the leak almost had to be the outer tub's Centerpost Gasket. It was really the... Read more
Filters debris from water entering your washer and seals the hose connection. Replace if water fills slowly or screens are clogged. Confirm fit by model.
As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more
Fix a washer that won't agitate or leaves lint on clothes. This agitator base supports movement during wash cycles. DIY-friendly repair part.
The ridges inside the agitator base were stripped. Installed a new base - after a good cleaning of build-up on the spindle. Works like new! Read more
Fix loud clicking or grinding noises during spin cycles with this washer transmission gear case. Moderately difficult repair takes 1-2 hours.
Bought new Transmission/gear box. Putting in the new one was easy. Taking the old one out was a nightmare. The corrosion on the spanner nut and drive block was awful. Ten years of VERY hard water and six kids made for a lot of corrosion and hard water crystallization. I do not own a spanner wrench. I am not sure having one would've helped. I tried pipe wrenches, needle nose vice-grips and many other ways. What eventually worked was taking a three inch ratchet extension, putting it... Read more
Fix a washer that won't fill, fills slowly, or leaks water into the tub when off. This water inlet valve replacement typically takes 10-15 minutes to install.
Replaced water inlet valve took all of 10 minutes and washer is filling great on hot and cold. Thanks to Appliance Parts Pros for getting me the part within 24 hours. I have a very happy customer. Read more
Washer tub seal prevents water leaks between outer tub and inner basket. Replace if you notice leaking from below. Confirm fit with your model number.
This repair was performed on a Whirlpool Cabrio clothes washer Model # WTW5640XW0 which has the digital electronic controls rather than the older style timer, electro/mechanical controls. This washer was made in 2010. Simply having the diagnostic programs on this machine is wonderful and they work remarkably well and led me to the shifter/rpm sensor component straight away. It was a simple replacement by tipping the washer onto its front and accessing through the bottom. The machine was put... Read more
Flexible tube that drains used water from your washer tub to the standpipe. Replace if cracked, leaking at connections, or torn along the length.
After not finding the needed parts to extend the hose at home depot, i turned to online help. I was able to find the right parts quickly on your site and was able to even watch a few videos on how to do the repair. I was beyond amazed that the parts arrived the next day, even though a Saturday and even with standard shipping. I was fortunate enough that my repair did not need any real explanation and the job was done in less than 10 minutes. Felt really good to be able to solve the problem,... Read more