Jenn-Air Dishrack

This dishrack replaces a damaged or rusted rack in your dishwasher. Restoring a true-to-spec rack keeps plates, bowls, and cookware secure and properly spaced so the machine can clean effectively and the rack moves smoothly on its tracks. What it does:

• Organizes and supports dishes and cookware during wash and dry cycles
• Maintains proper spacing for spray coverage and drainage
• Interfaces with the rail system to slide in and out when paired with the correct rollers/stops for your model
• Common symptoms: rusted or broken tines, deteriorated rack coating, misshapen frame, rack falling off tracks or not sliding properly

• 1 dishrack

• Disconnect power to the dishwasher before servicing
• Open the door; pull the existing rack out. For upper racks, release/remove rack stops or end caps; for lower racks, lift straight out
• Transfer any reusable components (rollers, clips, fold-down tines, silverware basket) from the old rack
• Slide the new rack onto the rails and reinstall stops; verify smooth travel before running a cycle

Color: light gray. Measures about a 1/2 inch high by 4 inches deep.

The Rack Support (RH) is an OEM part for Whirlpool dishwashers. It is the plastic right-hand side bracket that secures the upper rack assembly inside the washer cavity. 

Causes of a damaged rack support include cracks or breaks from normal wear over extended use. Repeated impact from dishes loading/unloading can cause small stress fractures.

Symptoms of a faulty support include:  

• Loose or rattling upper dish rack during operation
• Difficulty sliding racks in/out smoothly
• Visible cracks or missing pieces on the support

This Whirlpool OEM part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

Color: White. This basket measures about 9 inches wide by 7 inches high by 6 inches deep. The cover and handle are not included. The cover is no longer available. For the handle order W11033847.

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

The Track Stop is an OEM part for Whirlpool dishwashers. It is a component located on the tracks inside the dishwasher that holds and guides rack movement during operation. 

Symptoms of a bad track stop include:

• Racks or dishes sliding uncontrollably during the cycle  
• Difficulty fully extending or retracting racks
• Noise or grinding sounds noticed from rack movement
• Damage or wear visible on the rack tracks

Causes of a bad track stop can be a failure due to normal wear and tear over repeated use. Opening and closing the dishwasher door thousands of times can degrade track stops.

This OEM Whirlpool replacement track stop ensures proper rack guiding, securing its position to deliver dependable performance cycle after cycle. This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

This pivot is a small rotating support used as the hinge/axle point for a moving component in the appliance. Replacing a worn or broken pivot restores smooth movement and proper alignment of the attached part.

• Provides the rotation point for a lever, flap, cover, or door
• Helps maintain alignment and reduce wobble or play
• Restores smooth opening/closing motion
• Common signs of failure: binding, sagging, squeaking, looseness, or visible damage

• Disconnect power; shut off gas/water before service
• Support the assembly to remove load from the pivot
• Remove retaining fastener/clip and note the original orientation
• Transfer any spacers/washers and reinstall; free movement before reassembly

Small clip that secures panels, trim or small components to keep parts properly seated and reduce rattling. Replacing a worn or broken clip helps restore fit and stops noise from loose assemblies. What it does:

• Secures trim, panels or small assemblies so parts stay aligned and stable
• Prevents vibration and rattling caused by loose or damaged fasteners
• Helps hold seals or wiring in place where used as a retainer
• Restores proper fit of the affected panel or component after failure

• Disconnect power to the appliance before servicing and work with dry hands
• Remove or loosen adjacent trim or panels as needed to access the clip location
• Note clip orientation, then press or snap the replacement clip into place until fully seated
• Reassemble panels and test appliance operation to confirm the repair

This genuine OEM adjuster helps set and fine-tune an appliance's alignment so doors close correctly and the cabinet sits level. It restores stable operation and reduces rocking or vibration caused by an uneven appliance surface. What it does:

• Provides a threaded adjustment point to raise, lower, or support an appliance corner or panel
• Helps correct uneven cabinets, tilted doors, or appliances that rock or vibrate during use
• Restores proper door alignment and sealing when misalignment is caused by height/level issues
• Works as the appliance's mechanical support where an adjustable foot or bracket is used

• Always disconnect power (and water, if applicable) before servicing the appliance
• Support the appliance securely before making height adjustments or removing/installing the adjuster
• Use appropriate hand tools; avoid excessive force that could damage threads or mounting points

The fold-away tine latch secures the flip-down tines on your dishwasher rack. It locks tines upright to support dishes and releases to fold them flat, restoring rack flexibility and preventing tines from collapsing during cycles.

• Locks fold-away tines in the up position to support dishes and glassware
• Releases to allow tines to fold flat for larger items
• Helps maintain stable, organized loading during wash cycles
• Common symptoms: tines won't stay upright, latch won't click/hold, missing or broken latch

• Open the dishwasher door and remove the affected rack for access
• Note the latch orientation; release the old latch from the tine assembly
• Snap the new latch into place until it engages
• A small flat-blade screwdriver can help release locking tabs

This positioner aligns and secures its mating component in the correct location inside your appliance. Replacing a cracked, worn, or missing positioner restores proper fit so the assembly stays put and operates as designed.

• Holds the related part in the proper position and orientation
• Prevents shifting, sagging, or rattling during use
• Supports smooth adjustment or movement where applicable
• Common symptoms: loose or misaligned component, difficulty adjusting or seating the piece, visible cracks, or a missing clip

• Disconnect power; also shut off gas or water if your appliance uses these utilities
• Note the original orientation and take photos before removal
• Transfer any reused hardware and fully seat tabs/slots to avoid damage
• Wear cut-resistant gloves and check alignment after reassembly

Color: Dark Gray

The Dishrack Stop Clip is an OEM component specifically designed for Whirlpool brand dishwashers. This clip functions to hold the upper dish rack in place during washing cycles.

Symptoms of a bad dishrack stop clip can include:

• Movement or vibration of the upper dish rack during washing
• Visible damage, bending or broken tabs on the mounting clip itself  
• Inability to smoothly slide or remove the upper dish rack

Causes of a bad dishrack stop clip usually stem from normal wear and tear over extended use. Overtight loading of dishes could also put excessive stress on the clip.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.